Control of shock-induced vortex breakdown on a delta-wing-body configuration in the transonic regime

2021 ◽  
pp. 1-25
Author(s):  
Rajan B. Kurade ◽  
L. Venkatakrishnan ◽  
G. Jagadeesh
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Pressure Fluctuations ◽  
Angle Of Attack ◽  
Aerodynamic Coefficients ◽  
Delta Wings ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sudden Jump ◽  
Modest Level

Abstract Shock-induced vortex breakdown, which occurs on the delta wings at transonic speed, causes a sudden and significant change in the aerodynamic coefficients at a moderate angle-of-attack. Wind-tunnel tests show a sudden jump in the aerodynamic coefficients such as lift force, pitching moment and centre of pressure which affect the longitudinal stability and controllability of the vehicle. A pneumatic jet operated at sonic condition blown spanwise and along the vortex core over a 60° swept delta-wing-body configuration is found to be effective in postponing this phenomenon by energising the vortical structure, pushing the vortex breakdown location downstream. The study reports that a modest level of spanwise blowing enhances the lift by about 6 to 9% and lift-to-drag ratio by about 4 to 9%, depending on the free-stream transonic Mach number, and extends the usable angle-of-attack range by 2°. The blowing is found to reduce the magnitude of unsteady pressure fluctuations by 8% to 20% in the aft portion of the wing, depending upon the method of blowing. Detailed investigations carried out on the location of blowing reveal that the blowing close to the apex of the wing maximises the benefits.

Effect of anhedral on a reverse delta wing

2017 ◽  
Vol 232 (12) ◽  
pp. 2317-2325 ◽  
Author(s):  
T Lee ◽  
LS Ko ◽  
V Tremblay-Dionne
Keyword(s):  
Lift Force ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Tangential Velocity ◽  
Bottom Surface ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The effect of anhedral on the vorticity flowfield and aerodynamic loadings of a slender reverse delta wing was studied experimentally. The addition of anhedral always led to a reduced lift and lift-to-drag ratio in comparison with their clean-wing counterparts. The drag was increased with increasing anhedral compared to the clean wing at the same lift condition. The reverse delta wing vortex retained its regularity to a higher angle of attack as the anhedral was increased. The persistent outboard location of the reverse delta wing vortex suggests that the lift force was mainly produced by the pressure exerted on the bottom surface of the wing. The anhedral also led to an increased vorticity level and tangential velocity.

Some Effects of Thickness on the Longitudinal Characteristics of Sharp-Edged Delta Wings at Low Speeds

1968 ◽  
Vol 72 (686) ◽  
pp. 151-155 ◽  
Author(s):  
L. C. Squire
Keyword(s):  
Aspect Ratio ◽  
Delta Wing ◽  
Leading Edge ◽  
Air Transport ◽  
Wing Area ◽  
Delta Wings ◽  
Amount Of Information ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Passenger Cabin

Recently there has been renewed interest in the concept of an all-wing aircraft as a means of producing cheap air transport over relatively short distances. It is natural that with the large amount of information on slender wings now available an all-wing aircraft based on a sharp-edged slender planform should be considered for this role. One of the difficulties immediately faced in developing this concept is that since the aircraft must carry a large number of passengers it is necessary that as much of the wing area as possible should be deep enough to provide for a large passenger cabin. Thus the wing will be very thick over a large part of its area. If this condition is not met, then the aircraft has too much wing area and hence too high a structure weight. Typically one may think of an aircraft with a delta wing of aspect ratio 2 and with a wing thickness of from 15% to 20% of the root chord over as much of the wing area as possible. At first sight thickness of this order eliminates the main advantage of slender wings since the effect of thickness is usually to reduce the strength of the leading-edge vortices and hence the non-linear lift. Thus the incidence for a given lift is increased above that for a thin wing. This in turn means that the lift-to-drag ratio may be smaller.

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

scholarly journals Study of board bending degree on hydrodynamic performances of a single-layer cambered otter-board

2019 ◽  
Vol 131 ◽  
pp. 01120
Author(s):  
Lei Wang ◽  
Lu Min Wang ◽  
Yong Li Liu ◽  
Wen Wen Yu ◽  
Guang Rui Qi ◽  
...  
Keyword(s):  
Center Of Pressure ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Angle Of Attack ◽  
Single Layer ◽  
Moment Coefficient ◽  
Pitch Moment ◽  
Engineering Models ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The effect of board bending degree on hydrodynamic performances of a single-layer cambered otter-board was investigated using engineering models in a wind tunnel. Three different bending degree boards were evaluated at a wind speed of 28 m/s. Parameters measured included: drag coefficient Cx, lift coefficient Cy, pitch moment coefficient Cm, center of pressure coefficient Cp , over a range of angle of attack (0° to 70°). These coefficients were used in analyzing the differences in the performance among the three otter-board models. Results showed that the bending of the board(No. 2, No. 3) increased the water resistance of the otter-board, and improved the lift coefficient of the otter-board in the small angle of attack (0°<α≤20 °) ; the maximum lift coefficients Cy of otter-board model (No. 1) was higher (1.680, α = 25°). the maximum lift–drag ratios of models (No. 1, No. 2 and No. 3) are 6.822 (α = 7.5 °), 6.533 (α = 2.5 °) and 6.384 (α = 5.0°), which showed that the board bending reduces the lift-to-drag ratio of the otter-board.The stability of the No. 3 model was better than those two models (No. 1, No. 2) in most range of attack angle, but No. 1 otter-board model had a better stability in roll of otter-board. The findings of this study can offer useful reference data for the structural optimization of otter-boards for trawling.

Effects of leading-edge bevel angle on the aerodynamic forces of a non-slender 50° delta wing

2005 ◽  
Vol 109 (1098) ◽  
pp. 403-407 ◽  
Author(s):  
J. J. Wang ◽  
S. F. Lu
Keyword(s):  
Delta Wing ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Relative Thickness ◽  
Aerodynamic Performances ◽  
Stall Angle ◽  
Drag Ratio ◽  
Low Speed Wind Tunnel ◽  
Lift To Drag Ratio ◽  
Blunt Leading Edge

Abstract The aerodynamic performances of a non-slender 50° delta wing with various leading-edge bevels were measured in a low speed wind tunnel. It is found that the delta wing with leading-edge bevelled leeward can improve the maximum lift coefficient and maximum lift to drag ratio, and the stall angle of the wing is also delayed. In comparison with the blunt leading-edge wing, the increment of maximum lift to drag ratio is 200%, 98% and 100% for the wings with relative thickness t/c = 2%, t/c = 6.7% and t/c = 10%, respectively.

scholarly journals Effect of Blade Cambering on Dynamic Stall in View of Designing Vertical Axis Turbines

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Pablo Ouro ◽  
Thorsten Stoesser ◽  
Luis Ramírez
Keyword(s):  
Vertical Axis ◽  
Dynamic Stall ◽  
Hysteresis Cycle ◽  
Aerodynamic Coefficients ◽  
Pitching Motion ◽  
Large Eddy ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Good Agreement

This paper presents large eddy simulations (LESs) of symmetric and asymmetric (cambered) airfoils forced to undergo deep dynamic stall due to a prescribed pitching motion. Experimental data in terms of lift, drag, and moment coefficients are available for the symmetric NACA 0012 airfoil and these are used to validate the LESs. Good agreement between computed and experimentally observed coefficients is found confirming the accuracy of the method. The influence of foil asymmetry on the aerodynamic coefficients is analyzed by subjecting a NACA 4412 airfoil to the same flow and pitching motion conditions. Flow visualizations and analysis of aerodynamic forces allow an understanding and quantification of dynamic stall on both straight and cambered foils. The results confirm that cambered airfoils provide an increased lift-to-drag ratio and a decreased force hysteresis cycle in comparison to their symmetric counterparts. This may translate into increased performance and lower fatigue loads when using cambered airfoils in the design of vertical axis turbines (VATs) operating at low tip-speed ratios.

Wingtip Vortex Control Via Tip-Mounted Half-Delta Wings of Different Geometric Configurations

2015 ◽  
Vol 137 (12) ◽  
Author(s):  
T. Lee ◽  
S. Choi
Keyword(s):  
Tip Vortex ◽  
Delta Wings ◽  
Vortex Control ◽  
Vortex Pattern ◽  
Geometric Configurations ◽  
Wingtip Vortex ◽  
Wing Chord ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The control of the tip vortex, generated by a rectangular NACA 0012 wing, via tip-mounted half-delta wings (HDWs), of different slendernesses Λ, root chords cr, and deflections δ, was investigated experimentally at Re = 2.45 × 105. The results show that regardless of Λ, cr, and δ, the addition of HDWs consistently led to a diffused tip vortex. The degree of diffusion was, however, found to increase with decreasing Λ and cr. HDWs with cr ≤ 50% of the baseline-wing chord c caused a rapid diffusion of vorticity and rendered a weak circulation flowlike tip vortex, suggesting an enhanced wake-vortex decay and alleviation. The cr = 0.5c HDW also produced an improved lift-to-drag ratio. A unique double-vortex pattern also exhibited downstream of the cr ≤ 50%c HDW wings. The interaction and merging of the double vortex were expedited by upward HDW deflection.

Numerical exploration on drag and heat reduction mechanism of a spike-tipped supersonic blunt nose

2020 ◽  
Vol 34 (32) ◽  
pp. 2050370
Author(s):  
Yu-Shan Meng ◽  
Li Yan ◽  
Shi-Bin Li ◽  
Wei Huang
Keyword(s):  
Heat Flux ◽  
Drag Force ◽  
Stokes Equations ◽  
Angle Of Attack ◽  
Three Dimensional ◽  
Viscous Force ◽  
Reduction Mechanism ◽  
Complex Flow ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In this study, the drag force and heat flux reduction mechanism induced by the aerodisk (with disks on its nose) with the freestream Mach number being 4.937 has been numerically investigated, and the simulations have been carried out by the three-dimensional Reynolds-averaged Navier–Stokes equations coupled with the SST [Formula: see text] turbulence model. The influence of the angle of attack on the drag and heat flux reduction has been analyzed comprehensively. The obtained results show that the drag force of the spiked blunt body can be reduced by the aerodisk, and the drag force decreases by 24.63%. The flow mechanism of the complex flow is drastically modified by the angle of attack, and this results in a strong flow asymmetry. This asymmetry becomes more and more obvious as the angle of attack increases. Both the pressure force and viscous force increase with the increase of the angle of attack. Moreover, both the lift and drag coefficients increase as the angle of attack increases, and the lift-to-drag ratio increases first and then decreases with the increase of the angle of attack. When the angle of attack is [Formula: see text], the maximum lift-to-drag ratio is close to 0.36.

On the Vortex Breakdown Phenomenon in High Angle of Attack Flows Over Delta Wing Geometries

2014 ◽  
Author(s):  
Eric D. Robertson ◽  
Varun Chitta ◽  
D. Keith Walters ◽  
Shanti Bhushan
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
High Angle ◽  
High Angle Of Attack ◽  
Eddy Simulation ◽  
Wing Model

Using computational methods, an investigation was performed on the physical mechanisms leading to vortex breakdown in high angle of attack flows over delta wing geometries. For this purpose, the Second International Vortex Flow Experiment (VFE-2) 65° sweep delta wing model was studied at a root chord Reynolds number (Recr) of 6 × 106 at various angles of attack. The open-source computational fluid dynamics (CFD) solver OpenFOAM was used in parallel with the commercial CFD solver ANSYS® FLUENT. For breadth, a variety of classic closure models were applied, including unsteady Reynolds-averaged Navier-Stokes (URANS) and detached eddy simulation (DES). Results for all cases are analyzed and flow features are identified and discussed. The results show the inception of a pair of leading edge vortices originating at the apex for all models used, and a region of steady vortical structures downstream in the URANS results. However, DES results show regions of massively separated helical flow which manifests after vortex breakdown. Analysis of turbulence quantities in the breakdown region gives further insight into the mechanisms leading to such phenomena.

Sign in / Sign up

Export Citation Format

Share Document