Drag Characterization Study of Variable Camber Continuous Trailing Edge Flap

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Upender K. Kaul ◽  
Nhan T. Nguyen
Keyword(s):  
Transport Model ◽  
Computational Study ◽  
Lift Coefficient ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Characterization Study ◽  
Analysis Of Results ◽  
Trailing Edge Flap ◽  
Lift And Drag ◽  
Flap Region

A Reynolds-averaged Navier–Stokes (RANS) computational study was conducted to investigate the effect of various variable camber continuous trailing edge flap (VCCTEF) configurations on the lift and drag of a NASA generic transport model (GTM) wing section. Out of the five two-dimensional (2D) VCCTEF configurations considered with varying camber in the three-segment flap region, with a total deflection of 6 deg, the best stall performance was exhibited by the circular and parabolic arc camber flaps. Both circular and parabolic arc flaps give similar lift performance, with the circular arc yielding a higher lift coefficient and parabolic arc resulting in the lowest drag and hence the best L/D performance at design Cl. Analysis of results based on linear theory shows excellent agreement between computed and theoretical incremental lift.

scholarly journals Numerical Study of Variable Camber Continuous Trailing Edge Flap at Off-Design Conditions

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3185 ◽  
Author(s):  
Mohammed Abdul Raheem ◽  
Prasetyo Edi ◽  
Amjad A. Pasha ◽  
Mustafa M. Rahman ◽  
Khalid A. Juhany
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Computational Study ◽  
Advanced Technology ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Navier Stokes Equations ◽  
Parabolic Profile ◽  
Trailing Edge Flap ◽  
Laminar Flow Control

Numerical simulations are performed to study the outboard airfoil of advanced technology regional aircraft (ATRA) wings with five different variable camber continuous trailing edge flap (VCCTEF) configurations. The computational study aims to improve the aerodynamic efficiency of the airfoil under cruise conditions. The design of outboard airfoil complies with the hybrid laminar flow control design criteria. This work is unique in terms of analysis of the effects of VCCTEF on the ATRA wing’s outboard airfoil during the off-design condition. The Reynolds–Averaged Navier–Stokes equations coupled with the Spalart-Allmaras turbulence model are employed to perform the simulations for the baseline case and VCCTEF configurations. The current computational study is performed at an altitude of 10 km with a cruise Mach number of 0.77 and a Reynolds number of 2.16 × 107. Amongst all five configurations of VCCTEF airfoils studied, a flap having a parabolic profile (VCCTEF 123) configuration shows the maximum airfoil efficiency and resulted in an increase of 6.3% as compared to the baseline airfoil.

Aeroelastic Analysis of Membrane Microair Vehicles—Part II: Computational Study of a Plunging Membrane Airfoil

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Peter J. Attar ◽  
Raymond E. Gordnier ◽  
Jordan W. Johnston ◽  
William A. Romberg ◽  
Ramkumar N. Parthasarathy
Keyword(s):  
Strouhal Number ◽  
Stokes Equations ◽  
Computational Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Reduced Frequency ◽  
Lift And Drag ◽  
Intermediate Value

In the second paper of the two part study of membrane microair vehicles, computations are performed for a plunging membrane airfoil. The computational model uses a sixth-order finite difference solution of the Navier–Stokes equations coupled to a finite element solution of a set of nonlinear string equations. The effect, on the structural and fluid response, of plunging Strouhal number, reduced frequency, and static angle of attack is examined. Qualitatively, the flow field is found to be very complex with interactions of vortices shed from various locations along the chord of the airfoil. At a low angle of attack and a low Strouhal number, increasing reduced frequency results in a decrease and an increase in the mean sectional lift and drag coefficients, respectively. Also, at a low angle of attack, increasing the Strouhal number has minimal effect at high and low values of reduced frequencies, but a significant effect is found at an intermediate value of reduced frequency. When the effect of angle of attack is studied for fixed values of Strouhal number and reduced frequency, it is found that the act of plunging gives improved mean sectional lift when compared with the case of a fixed flexible airfoil. The improvement does not increase monotonically with the angle of attack but instead is maximum at an intermediate value. Finally, increasing the value of the membrane prestrain, which stiffens the airfoil, results in a reduced value of the sectional lift coefficient for a given Strouhal number, reduced frequency, and angle of attack.

Stability Analysis of a Light Aircraft Configuration Using Computational Fluid Dynamics

2012 ◽  
Vol 225 ◽  
pp. 391-396 ◽  
Author(s):  
Mohammed Mahdi ◽  
Yasser A. Elhassan
Keyword(s):  
Numerical Simulation ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Rate Of Change ◽  
Navier Stokes ◽  
Rolling Moment ◽  
Moment Coefficient ◽  
Stability Derivatives ◽  
Lift And Drag

This work aims to simulate and study the flow field around SAFAT-01 aircraft using numerical solution based on solving Reynolds Averaged Navier-Stokes equations coupled with K-ω SST turbulent model. The aerodynamics behavior of SAFAT-01 aircraft developed at SAFAT aviation complex were calculated at different angles of attack and side slip angles. The x,y and z forces and moments were calculated at flight speed 50m/s and at sea level condition. Lift and drag curves for different angles of attack were plotted. The maximum lift coefficient for SAFAT-01 was 1.67 which occurred at angle of attack 16° and Maximum lift to drag ratio (L/D) was 14 which occurred at α=3°, and the zero lift drag coefficient was 0.0342. Also the yawing moment coefficient was plotted for different side slip angles as well as rolling moment. The longitudinal stability derivatives with respect to angle of attack, speed variation (u), rate of pitch (q) and time rate of change of angle of attack were calculated using obtained CFD results. Concerning lateral stability only side slips derivatives were calculated. To validate this numerical simulation USAF Digital DATCOM is used to analyze this aircraft; a comparison between predicted results for this aircraft and Digital DATCOM indicated that this numerical simulation has high ability for predicting the aerodynamics characteristics.

scholarly journals Active Control of a Stalled Airfoil Through Steady or Unsteady Actuation Jets

2015 ◽  
Vol 137 (9) ◽  
Author(s):  
V. G. Chapin ◽  
E. Benard
Keyword(s):  
Active Control ◽  
Computational Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Position Angle ◽  
Navier Stokes ◽  
Suction Surface ◽  
Parametric Studies ◽  
Naca 0012

The active control of the leading-edge (LE) separation on the suction surface of a stalled airfoil (NACA 0012) at a Reynolds number of 106 based on the chord length is investigated through a computational study. The actuator is a steady or unsteady jet located on the suction surface of the airfoil. Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations are solved on hybrid meshes with the Spalart–Allmaras turbulence model. Simulations are used to characterize the effects of the steady and unsteady actuation on the separated flows for a large range of angle of attack (0 < α < 28 deg). Parametric studies are carried out in the actuator design-space to investigate the control effectiveness and robustness. An optimal actuator position, angle, and frequency for the stalled angle of attack α = 19 deg are found. A significant increase of the lift coefficient is obtained (+ 84% with respect to the uncontrolled reference flow), and the stall is delayed from angle of attack of 18 deg to more than 25 deg. The physical nonlinear coupling between the actuator position, velocity angle, and frequency is investigated. The critical influence of the actuator location relative to the separation location is emphasized.

scholarly journals Effect of Leading-Edge Bulges on Aerodynamic Characteristics of Bionic Wingsail

2021 ◽  
Author(s):  
Chen Li ◽  
Peiting Sun ◽  
Hongming Wang
Keyword(s):  
Stokes Equations ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Suction Surface ◽  
Ansys Fluent ◽  
Navier Stokes Equations ◽  
Extension Direction ◽  
Lift And Drag

The leading-edge bulges along the extension direction are designed on the marine wingsail. The height and the spanwise wavelength of the protuberances are 0.1c and 0.25c, respectively. At Reynolds number Re=5×105, the Reynolds Averaged Navier-Stokes equations are applied to the simulation of the wingsail with the bulges thanks to ANSYS Fluent finite-volume solver based on the SST K-ω models. The grid independence analysis is carried out with the lift and drag coefficients of the wingsail at AOA = 8° and AOA=20°. The results show that while the efficiency of the wingsail is reduced by devising the leading-edge bulges before stall, the bulges help to improve the lift coefficient of the wingsail when stalling. At AOA=22° under the action of the leading-edge tubercles, a convective vortex is formed on the suction surface of the modified wingsail, which reduces the flow loss. So the bulges of the wingsail can delay the stall.

Performance Studies on a Wind Turbine Blade Section for Low Wind Speeds With a Gurney Flap

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
M. Rafiuddin Ahmed ◽  
Epeli Nabolaniwaqa
Keyword(s):  
Wind Turbines ◽  
Lift Coefficient ◽  
Flow Characteristics ◽  
Trailing Edge ◽  
Wind Speeds ◽  
Gurney Flap ◽  
Trailing Edge Flaps ◽  
Blade Section ◽  
Low Wind Speeds ◽  
Lift And Drag

The flow characteristics and the lift and drag behavior of a thick trailing-edged airfoil that was provided with fixed trailing-edge flaps (Gurney flaps) of 1–5% height right at the back of the airfoil were studied both experimentally and numerically at different low Reynolds numbers (Re) and angles of attack for possible applications in wind turbines suitable for the wind speeds of 4–6 m/s. The flap considerably improves the suction on the upper surface of the airfoil resulting in a higher lift coefficient. The drag coefficient also increased; however, the increase was less compared with the increase in the lift coefficient, resulting in a higher lift-to-drag ratio in the angles of attack of interest. The results show that trailing-edge flaps can improve the performance of blades designed for low wind speeds and can be directly applied to small wind turbines that are increasingly being used in remote places or in smaller countries.

Aero-Thermal Investigation of a Rib-Roughened Trailing Edge Channel With Crossing-Jets: Part II—Heat Transfer Analysis

2008 ◽  
Author(s):  
Filippo Coletti ◽  
Alessandro Armellini ◽  
Tony Arts ◽  
Christophe Scholtes
Keyword(s):  
Heat Transfer ◽  
Computational Study ◽  
Heat Transfer Analysis ◽  
Navier Stokes ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Present Contribution ◽  
Heat Transfer Coefficients ◽  
Numerical Predictions ◽  
Rib Roughened

The present contribution addresses the aero-thermal experimental and computational study of a trapezoidal cross-section model simulating a trailing edge cooling cavity with one rib-roughened wall and slots along two opposite walls. Highly resolved heat transfer distributions for the geometry with and without ribs are achieved using a steady state liquid crystals method in part II of this paper. The reference Reynolds number, defined at the entrance of the test section, is set at 67500 for all the experiments. Comparisons are made with the flow field visualizations presented in part I of the paper. The results show the dramatic impact of the flow structures on the local and global heat transfer coefficients along the cavity walls. Of particular importance is the jet deflected by the rib-roughened wall and impinging on the opposite smooth wall. The experimental results are compared with the numerical predictions obtained using the finite volume, Reynolds-Averaged Navier-Stokes solver CEDRE.

Spectral Difference Solution of Incompressible Flow Over an Inline Tube Bundle With Oscillating Cylinder

2012 ◽  
Author(s):  
Christopher Cox ◽  
Chunlei Liang ◽  
Michael Plesniak
Keyword(s):  
Forced Oscillation ◽  
Stokes Equations ◽  
Tube Bundle ◽  
Lift Coefficient ◽  
Flow Simulation ◽  
Navier Stokes ◽  
Spectral Difference ◽  
Navier Stokes Equations ◽  
Incompressible Viscous Flow ◽  
Lift And Drag

A high-order spectral difference (SD) method for solving the Navier-Stokes equations on moving, deformable unstructured grids has been developed [1]. In this paper, the SD method and the artificial compressibility method (ACM) are integrated with a dual time-stepping scheme to model unsteady incompressible viscous flow past an inline tube bundle of cylinders equally sized (diameter = d) and spaced (spacing = 2.1*d) over an unstructured grid. Flow simulation results are obtained using a fourth-order space accurate SD method. Two forced oscillation cases are considered; (1) 1st cylinder oscillation and (2) 2nd cylinder oscillation. The Reynolds number used for both cases is 100 and the flow is laminar. Forced oscillation is performed in the tranverse direction, and the subsequent altering of the flow physics of the system is studied. The frequency of vortex shedding behind each cylinder is the same. Root mean square results show that the lift coefficient is greatest for the 4th inline cylinder in both cases. Furthermore, a reduction in both lift and drag coefficients is seen from case (1) to case (2).

A Computational Study of the Flow Around an Isolated Wheel in Contact With the Ground

2005 ◽  
Vol 128 (3) ◽  
pp. 520-530 ◽  
Author(s):  
James McManus ◽  
Xin Zhang
Keyword(s):  
Computational Study ◽  
Experimental Results ◽  
Navier Stokes ◽  
Flow Structures ◽  
Road Vehicles ◽  
Accurate Representation ◽  
Drag Forces ◽  
Mechanisms Of Formation ◽  
Lift And Drag ◽  
Good Agreement

The flow around an isolated wheel in contact with the ground is computed by the Unsteady Reynolds-Averaged Navier-Stokes (URANS) method. Two cases are considered, a stationary wheel on a stationary ground and a rotating wheel on a moving ground. The computed wheel geometry is a detailed and accurate representation of the geometry used in the experiments of Fackrell and Harvey. The time-averaged computed flow is examined to reveal both new flow structures and new details of flow structures known from previous experiments. The mechanisms of formation of the flow structures are explained. A general schematic picture of the flow is presented. Surface pressures and pressure lift and drag forces are computed and compared to experimental results and show good agreement. The grid sensitivity of the computations is examined and shown to be small. The results have application to the design of road vehicles.

scholarly journals Effects of Micro-Tab on the Lift Enhancement of Airfoil S-809 with Trailing-Edge Flap

Processes ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 547
Author(s):  
Jianjun Ye ◽  
Shehab Salem ◽  
Juan Wang ◽  
Yiwen Wang ◽  
Zonggang Du ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Flow Behavior ◽  
Air Flow ◽  
Lift Coefficient ◽  
Pressure Coefficient ◽  
Turbine Blades ◽  
Lower Surface ◽  
Wind Turbine Blades ◽  
Trailing Edge ◽  
Trailing Edge Flap

Recently, the Trailing-Edge Flap with Micro-Tab (TEF with Micro-Tab) has been exploited to enhance the performance of wind turbine blades. Moreover, it can also be used to generate more lift and delay the onset of stall. This study focused mostly on the use of TEF with Micro-Tab in wind turbine blades using NREL’s S-809 as a model airfoil. In particular, the benefits generated by TEF with Micro-Tab may be of great interest in the design of wind turbine blades. In this paper, an attempt was made to evaluate the influence of TEF with Micro-Tab on the performance of NREL’s S-809 airfoils. Firstly, a computational fluid dynamics (CFD) model for the airfoil NREL’s S-809 was established, and validated by comparison with previous studies and wind tunnel experimental data. Secondly, the effects of the flap position (H) and deflection angle (αF) on the flow behaviors were investigated. As a result, the effect of TEF on air-flow behavior was demonstrated by augmenting the pressure coefficient at the lower surface of the airfoil at flap position 80% chord length (C) and αF = 7.5°. Thirdly, the influence of TEF with Micro-Tab on the flow behaviors of the airfoil NREL’s S-809 was studied and discussed. Different Micro-Tab positions and constant TEF were examined. Finally, the effects of TEF with Micro-Tab on the aerodynamic characteristics of the S-809 with TEF were compared. The results showed that an increase in the maximum lift coefficient by 25% and a delay in the air-flow stall were accomplished due to opposite sign vortices, which was better than the standard airfoil and S-809 with TEF. Therefore, it was deduced that the benefits of TEF with Micro-Tab were apparent, especially at the lower surface of the airfoil. This particularly suggests that the developed model could be used as a new trend to modify the designs of wind turbine blades.

Sign in / Sign up

Export Citation Format

Share Document