On the Applicability of Cavitation Erosion Risk Models With a URANS Solver

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Themistoklis Melissaris ◽  
Norbert Bulten ◽  
Tom J. C. van Terwisga
Keyword(s):  
Cavitation Erosion ◽  
Navier Stokes ◽  
Maritime Industry ◽  
Risk Models ◽  
Erosion Risk ◽  
Erosion Prediction ◽  
Computational Fluid Dynamics Cfd ◽  
Propeller Blades ◽  
Energy Balance Approach ◽  
Scale Data

In the maritime industry, cavitation erosion prediction becomes more and more critical, as the requirements for more efficient propellers increase. Model testing is yet the most typical way a propeller designer can, nowadays, get an estimation of the erosion risk on the propeller blades. However, cavitation erosion prediction using computational fluid dynamics (CFD) can possibly provide more information than a model test. In the present work, we review erosion risk models that can be used in conjunction with a multiphase unsteady Reynolds‐averaged Navier–Stokes (URANS) solver. Three different approaches have been evaluated, and we conclude that the energy balance approach, where it is assumed that the potential energy contained in a vapor structure is proportional to the volume of the structure, and the pressure difference between the surrounding pressure and the pressure within the structure, provides the best framework for erosion risk assessment. Based on this framework, the model used in this study is tested on the Delft Twist 11 hydrofoil, using a URANS method, and is validated against experimental observations. The predicted impact distribution agrees well with the damage pattern obtained from paint test. The model shows great potential for future use. Nevertheless, it should further be validated against full scale data, followed by an extended investigation on the effect of the driving pressure that leads to the collapse.

Assessment of Cavitation Erosion With a URANS Method

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Zi-ru Li ◽  
Mathieu Pourquie ◽  
Tom van Terwisga
Keyword(s):  
Large Scale ◽  
Cavitation Erosion ◽  
Time Derivative ◽  
Mean Value ◽  
Navier Stokes ◽  
Local Pressure ◽  
Erosion Risk ◽  
Damage Area ◽  
Large Scale Structures ◽  
Unsteady Rans

An assessment of the cavitation erosion risk by using a contemporary unsteady Reynolds-averaged Navier–Stokes (URANS) method in conjunction with a newly developed postprocessing procedure is made for an NACA0015 hydrofoil and an NACA0018-45 hydrofoil, without the necessity to compute the details of the actual collapses. This procedure is developed from detailed investigations on the flow over a hydrofoil. It is observed that the large-scale structures and typical unsteady dynamics predicted by the URANS method with the modified shear stress transport (SST) k-ω turbulence model are in fair agreement with the experimental observations. An erosion intensity function for the assessment of the risk of cavitation erosion on the surface of hydrofoils by using unsteady RANS simulations as input is proposed, based on the mean value of the time derivative of the local pressure that exceeds a certain threshold. A good correlation is found between the locations with a computed high erosion risk and the damage area observed from paint tests.

Computational Fluid Dynamic Using Parallel Loop of Multi-Cores Processor

2014 ◽  
Vol 493 ◽  
pp. 80-85 ◽  
Author(s):  
C.L Siow ◽  
Jaswar ◽  
Efi Afrizal
Keyword(s):  
Fluid Flow ◽  
Early Stage ◽  
Fluid Dynamic ◽  
Visual Basic ◽  
Computer Hardware ◽  
Navier Stokes ◽  
Computer Memory ◽  
Large Size ◽  
Computational Fluid Dynamics Cfd ◽  
Reynolds Average

Computational Fluid Dynamics (CFD) software is often used to study fluid flow and structures motion in fluids. The CFD normally requires large size of arrays and computer memory and then caused long execution time. However, Innovation of computer hardware such as multi-cores processor provides an alternative solution to improve this programming performance. This paper discussed loop parallelize multi-cores processor for optimization of sequential looping CFD code. This loop parallelize CFD was achieved by applying multi-tasking or multi-threading code into the original CFD code which was developed by one of the authors. The CFD code was developed based on Reynolds Average Navier-Stokes (RANS) method. The new CFD code program was developed using Microsoft Visual Basic (VB) programming language. In the early stage, the whole CFD code was constructed in a sequential flow before it is modified to parallel flow by using VBs multi-threading library. In the comparison, fluid flow around the hull of round-shaped FPSO was selected to compare the performance of both the programming codes. Besides, executed results of this self-developed code such as pressure distribution around the hull were also presented in this paper.

Analysis of Hydrodynamic Characteristics in the Process of Autonomous Underwater Vehicle Docking

2015 ◽  
Author(s):  
Xiaoxu Du ◽  
Huan Wang
Keyword(s):  
Drag Coefficient ◽  
Autonomous Underwater Vehicle ◽  
Simple Algorithm ◽  
Underwater Vehicle ◽  
Navier Stokes ◽  
Hydrodynamic Characteristics ◽  
Successful Operation ◽  
Underwater Docking ◽  
Computational Fluid Dynamics Cfd ◽  
Volume Method

The successful operation of an Autonomous Underwater Vehicle (AUV) requires the capability to return to a dock. A number of underwater docking technologies have been proposed and tested in the past. The docking allows the AUV to recharge its batteries, download data and upload new instructions, which is helpful to improve the working time and efficiency. During the underwater docking process, unsteady hydrodynamic interference occurs between the docking device and an AUV. To ensure a successful docking, it is very important that the underwater docking hydrodynamics of AUV is understood. In this paper, numerical simulations based on the computational fluid dynamics (CFD) solutions were carried out for a 1.85m long AUV with maximum 0.2 m in diameter during the docking process. The two-dimensional AUV model without fin and rudder was used in the simulation. The mathematical model based on the Reynolds-averaged Navier-Stokes (RANS) equations was established. The finite volume method (FVM) and the dynamic structured mesh technique were used. SIMPLE algorithm and the k-ε turbulence model in the Descartes coordinates were also adopted. The hydrodynamics characteristics of different docking states were analyzed, such as the different docking velocity, the docking device including baffle or not. The drag coefficients of AUV in the process of docking were computed for various docking conditions, i.e., the AUV moving into the docking in the speed of 1m/s, 2m/s, 5m/s. The results indicate that the drag coefficient increases slowly in the process of AUV getting close to the docking device. When the AUV moves into the docking device, the drag coefficient increases rapidly. Then the drag coefficient decreases rapidly. The drag coefficient decreases with the increase of velocity when AUV enters the docking device. It was also found that the drag coefficient can be effectively reduced by dislodging the baffle of docking device.

Modeling of Compressor Drum Cavities With Radial Inflow

2016 ◽  
Author(s):  
D. Amirante ◽  
Z. Sun ◽  
J. W. Chew ◽  
N. J. Hills ◽  
N. R. Atkins
Keyword(s):  
Thermal Stratification ◽  
Turbulence Modeling ◽  
Navier Stokes ◽  
Inflow Rate ◽  
Cfd Models ◽  
Flow And Heat Transfer ◽  
Rotating Discs ◽  
Computational Fluid Dynamics Cfd ◽  
Inlet Conditions ◽  
Cooling Air

Reynolds-Averaged Navier-Stokes (RANS) computations have been conducted to investigate the flow and heat transfer between two co-rotating discs with an axial throughflow of cooling air and a radial bleed introduced from the shroud. The computational fluid dynamics (CFD) models have been coupled with a thermal model of the test rig, and the predicted metal temperature compared with the thermocouple data. CFD solutions are shown to vary from a buoyancy driven regime to a forced convection regime, depending on the radial inflow rate prescribed at the shroud. At a high radial inflow rate, the computations show an excellent agreement with the measured temperatures through a transient rig condition. At a low radial inflow rate, the cavity flow is destabilized by the thermal stratification. Good qualitative agreement with the measurements is shown, although a significant over-prediction of disc temperatures is observed. This is associated with under prediction of the penetration of the axial throughflow into the cavity. The mismatch could be the result of strong sensitivity to the prescribed inlet conditions, in addition to possible shortcomings in the turbulence modeling.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

The Effect of Turbulence and Real Gas Models on the Two Phase Spontaneously Condensing Flows in Nozzle

2013 ◽  
Author(s):  
Yogini Patel ◽  
Giteshkumar Patel ◽  
Teemu Turunen-Saaresti
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Nucleation Theory ◽  
Classical Nucleation Theory ◽  
Navier Stokes ◽  
Two Phase ◽  
Real Gas ◽  
Spontaneous Condensation ◽  
Condensing Flows ◽  
Computational Fluid Dynamics Cfd

The aim of the paper is to analyse the effect of turbulence and real gas models on the process of spontaneous condensation in converging diverging (CD) nozzle by using commercial Computational Fluid Dynamics (CFD) code. The calculations were based on the 2-D compressible Navier-Stokes (NS) equations coupled with two-equation turbulence model, and the non-equilibrium spontaneous condensing steam flow was solved on the basis of the classical nucleation theory. The results were validated to the available experimental data.

scholarly journals Three-Dimensional Navier–Stokes Analysis and Redesign of an Imbedded Bellmouth Nozzle in a Turbine Cascade Inlet Section

1996 ◽  
Vol 118 (3) ◽  
pp. 529-535 ◽  
Author(s):  
P. W. Giel ◽  
J. R. Sirbaugh ◽  
I. Lopez ◽  
G. J. Van Fossen
Keyword(s):  
Three Dimensional ◽  
Navier Stokes ◽  
Experimental Measurements ◽  
Inlet Section ◽  
Turbine Cascade ◽  
Blade Cascade ◽  
Inlet Geometry ◽  
Computational Fluid Dynamics Cfd ◽  
Transonic Turbine ◽  
Flow Nonuniformity

Experimental measurements in the inlet of a transonic turbine blade cascade showed unacceptable pitchwise flow nonuniformity. A three-dimensional, Navier–Stokes computational fluid dynamics (CFD) analysis of the imbedded bellmouth inlet in the facility was performed to identify and eliminate the source of the flow nonuniformity. The blockage and acceleration effects of the blades were accounted for by specifying a periodic static pressure exit condition interpolated from a separate three-dimensional Navier–Stokes CFD solution of flow around a single blade in an infinite cascade. Calculations of the original inlet geometry showed total pressure loss regions consistent in strength and location to experimental measurements. The results indicate that the distortions were caused by a pair of streamwise vortices that originated as a result of the interaction of the flow with the imbedded bellmouth. Computations were performed for an inlet geometry that eliminated the imbedded bellmouth by bridging the region between it and the upstream wall. This analysis indicated that eliminating the imbedded bellmouth nozzle also eliminates the pair of vortices, resulting in a flow with much greater pitchwise uniformity. Measurements taken with an installed redesigned inlet verify that the flow nonuniformity has indeed been eliminated.

A Verification and Validation Study of CFD Simulation of Wind-Induced Ventilation on Building with Single-Sided Opening

2014 ◽  
Vol 554 ◽  
pp. 696-700 ◽  
Author(s):  
Nur Farhana Mohamad Kasim ◽  
Sheikh Ahmad Zaki ◽  
Mohamed Sukri Mat Ali ◽  
Ahmad Faiz Mohammad ◽  
Azli Abd Razak
Keyword(s):  
Open Source Software ◽  
Natural Ventilation ◽  
Cfd Simulation ◽  
Previous Experiment ◽  
Experimental Methods ◽  
Verification And Validation ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Computational Fluid Dynamics Cfd ◽  
Model Approach

Wind-induced ventilation is widely acknowledged as one of the best approaches for inducing natural ventilation. Computational fluid dynamics (CFD) technique is gaining popularity among researchers as an alternative for experimental methods to investigate the behavior of wind-driven ventilation in building. In this present paper, Reynolds averaged Navier-Stokes equation (RANS) k-ε model approach is considered to simulate the airflow on a simplified cubic building with an opening on a single façade. Preliminary simulation using models from previous experiment indicates the reliability of OpenFOAM, the open source software that will be used in this study. The results obtained in this study will better define options for our future study which aims to explore how different buildings arrays modify the airflow inside and around a naturally ventilated building.

scholarly journals Experimental Validation Data for Computational Fluid Dynamics of Forced Convection on a Vertical Flat Plate

2015 ◽  
Vol 138 (1) ◽  
Author(s):  
Jeff R. Harris ◽  
Blake W. Lance ◽  
Barton L. Smith
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Forced Convection ◽  
Vertical Plate ◽  
Navier Stokes ◽  
Validation Dataset ◽  
System Response ◽  
Cfd Validation ◽  
Validation Data ◽  
Computational Fluid Dynamics Cfd

A computational fluid dynamics (CFD) validation dataset for turbulent forced convection on a vertical plate is presented. The design of the apparatus is based on recent validation literature and provides a means to simultaneously measure boundary conditions (BCs) and system response quantities (SRQs). All important inflow quantities for Reynolds-Averaged Navier-Stokes (RANS). CFD are also measured. Data are acquired at two heating conditions and cover the range 40,000 < Rex < 300,000, 357 <  Reδ2 < 813, and 0.02 < Gr/Re2 < 0.232.

Sign in / Sign up

Export Citation Format

Share Document