Numerical Investigation on the Effect of Rotation and Holes Arrangement in Cold Bridge-Type Impingement Cooling Systems

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Simone Paccati ◽  
Lorenzo Cocchi ◽  
Lorenzo Mazzei ◽  
Antonio Andreini
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Mutual Influence ◽  
Cooling System ◽  
Leading Edge ◽  
Lateral Spreading ◽  
Test Point ◽  
Navier Stokes ◽  
Specific Flow ◽  
Bridge Type

Abstract This work presents the results of a numerical analysis performed on a gas turbine leading edge cooling system. The investigation was carried out in order to provide a detailed interpretation of the outcomes of a parallel experimental campaign. The cooling geometry consists of a cold bridge-type impingement system: a radial channel feeds an array of holes, which in turn generate impingement jets cooling down the inner side of the leading edge surface. Coolant is extracted by five rows of holes, replicating film cooling and showerhead systems. Two impingement geometries were considered, presenting different holes arrangements and diameters but sharing the same overall passage area, in order to highlight the effect of different coolant distributions inside the leading edge cavity. For both geometries, a single test point was investigated in static and rotating conditions, with an equivalent slot Reynolds number of around 8200 and feeding conditions corresponding to the midspan radial section of the blade. Both steady Reynolds averaged Navier Stokes (RANS) approach and scale adaptive simulation (SAS) were tested. Due to the strong unsteadiness of the flow field, the latter proved to be superior: as a consequence, the SAS approach was adopted to study every case. A fairly good agreement was observed between the measured and computed heat transfer distributions, which allowed to exploit the numerical results to get a detailed description of the phenomena associated with the different cases. Results reveal that the two holes arrangements lead to strongly different heat transfer patterns, related to the specific flow phenomena occurring inside the leading edge cavity and to the mutual influence of the various system features. Rotational effects also appear to interact with the supply condition, altering the jet lateral spreading and the overall heat transfer performance.

Numerical Investigation on the Effect of Rotation and Holes Arrangement in Cold Bridge Type Impingement Cooling Systems

2019 ◽  
Author(s):  
S. Paccati ◽  
L. Cocchi ◽  
L. Mazzei ◽  
A. Andreini
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Mutual Influence ◽  
Cooling System ◽  
Leading Edge ◽  
Lateral Spreading ◽  
Test Point ◽  
Specific Flow ◽  
Flow Phenomena ◽  
Bridge Type

Abstract This work presents the results of a numerical analysis performed on a gas turbine leading edge cooling system. The investigation was carried out in order to provide a detailed interpretation of the outcomes of a parallel experimental campaign. The cooling geometry consists of a cold bridge type impingement system: a radial channel feeds an array of holes, which in turn generate impingement jets cooling down the inner side of the leading edge surface. Coolant is extracted by five rows of holes, replicating film cooling and showerhead systems. Two impingement geometries were considered, presenting different holes arrangements and diameters but sharing the same overall passage area, in order to highlight the effect of different coolant distributions inside the leading edge cavity. For both geometries a single test point was investigated in static and rotating conditions, with an equivalent slot Reynolds number of around 8200 and feeding conditions corresponding to the midspan radial section of the blade. Both steady RANS approach and Scale Adaptive Simulation (SAS) were tested. Due to the strong unsteadiness of the flow field, the latter proved to be superior: as a consequence, SAS approach was adopted to study every case. A fairly good agreement was observed between the measured and computed heat transfer distributions, which allowed to exploit the numerical results to get a detailed description of the phenomena associated with the different cases. Results reveal that the two holes arrangements lead to strongly different heat transfer patterns, related to the specific flow phenomena occurring inside the leading edge cavity and to the mutual influence of the various system features. Rotational effects also appear to interact with the supply condition, altering the jet lateral spreading and the overall heat transfer performance.

scholarly journals Heat Transfer on a Film-Cooled Rotating Blade

1999 ◽  
Author(s):  
Vijay K. Garg
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Three Dimensional ◽  
Leading Edge ◽  
Tip Clearance ◽  
Navier Stokes ◽  
Film Cooling Effectiveness ◽  
Film Cooling Holes

A multi-block, three-dimensional Navier-Stokes code has been used to compute heat transfer coefficient on the blade, hub and shroud for a rotating high-pressure turbine blade with 172 film-cooling holes in eight rows. Film cooling effectiveness is also computed on the adiabatic blade. Wilcox’s k-ω model is used for modeling the turbulence. Of the eight rows of holes, three are staggered on the shower-head with compound-angled holes. With so many holes on the blade it was somewhat of a challenge to get a good quality grid on and around the blade and in the tip clearance region. The final multi-block grid consists of 4784 elementary blocks which were merged into 276 super blocks. The viscous grid has over 2.2 million cells. Each hole exit, in its true oval shape, has 80 cells within it so that coolant velocity, temperature, k and ω distributions can be specified at these hole exits. It is found that for the given parameters, heat transfer coefficient on the cooled, isothermal blade is highest in the leading edge region and in the tip region. Also, the effectiveness over the cooled, adiabatic blade is the lowest in these regions. Results for an uncooled blade are also shown, providing a direct comparison with those for the cooled blade. Also, the heat transfer coefficient is much higher on the shroud as compared to that on the hub for both the cooled and the uncooled cases.

Clocking Effects of Inlet Non-Uniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side while the leading edge is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and high-pressure vanes are then investigated considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first one where hot spot and swirl core are aligned with passage and the second one where they are aligned with the leading edge. Comparisons between metal temperature distributions obtained from conjugate heat transfer simulations are performed evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The leading edge aligned configuration is resulted to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage aligned case. A strong sensitivity of both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

Aerodynamic and Heat Transfer Characterization of a Nozzle Vane Cascade With and Without Platform Cooling

2015 ◽  
Author(s):  
G. Barigozzi ◽  
A. Perdichizzi ◽  
M. Henze ◽  
J. Krueckels
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Cooling System ◽  
Leading Edge ◽  
Surface Flow ◽  
Secondary Flows ◽  
Intensity Level ◽  
Film Cooling Effectiveness ◽  
Nozzle Vane

In the present paper, aerodynamic and thermal performance of a linear nozzle vane cascade is fully assessed. Tests have been carried out with and without platform cooling, with coolant ejected through a slot located upstream of the leading edge. Cooling air is also ejected through a row of cylindrical holes located upstream of the slot, simulating a combustor cooling system. The cascade was tested at a high inlet turbulence intensity level (Tu1 = 9%) and at variable cooling injection conditions. Aero-thermal characterization of vane platform was obtained through 5-hole probe measurements, oil & dye surface flow visualizations, measurements of end wall adiabatic film cooling effectiveness and heat transfer coefficient. The platform cooling scheme operated at nominal injection rate was shown to effectively reduce the heat load over most of the platform surface, with only a small increase in secondary flows loss. Combustor holes injection resulted beneficial in controlling momentum of coolant approaching the cascade, thus limiting the secondary flows growth and resulting in an increase of the coolant film length inside of the passage.

Clocking Effects of Inlet Nonuniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane (HPV) equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side, while the leading edge (LE) is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-averaged Navier–Stokes simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and HPVs are then investigated, considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first in which hot spot and swirl core are aligned with passage; and the second in which they are aligned with the LE. Comparisons between metal temperature distributions obtained from conjugate heat transfer (CHT) simulations are performed, evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The LE aligned configuration is determined to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage-aligned case. A strong sensitivity to both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

Heat Transfer and Effectiveness for a Turbulent Boundary Layer With Tangential Fluid Injection

1960 ◽  
Vol 82 (4) ◽  
pp. 303-312 ◽  
Author(s):  
R. A. Seban
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Free Stream ◽  
Cooling System ◽  
Leading Edge ◽  
Free Stream Velocity ◽  
Stream Velocity ◽  
The Heat Transfer Coefficient

Experimental results are presented for the effectiveness and for the heat-transfer coefficient for a film cooling system in which air was used both for the film and for the free-stream fluids. Injection occurred at a single tangential slot near the leading edge of the plate and the slot size was varied. All flows were turbulent and the injection velocities covered a range from much less to much greater than the free-stream velocity. Correlations are realized for both the effectiveness and for the heat-transfer coefficient and, as in the past experience with such systems, separate specifications are needed for injection velocities greater and less than the free-stream velocity.

scholarly journals Effect of Rotation and Hole Arrangement in Cold Bridge-Type Impingement Cooling Systems

2019 ◽  
Vol 4 (2) ◽  
pp. 13 ◽  
Author(s):  
Lorenzo Cocchi ◽  
Alessio Picchi ◽  
Bruno Facchini
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Impingement Cooling ◽  
Complex Interactions ◽  
Supply Condition ◽  
Rotation Numbers ◽  
Supply Channel ◽  
Bridge Type

Experimental activity has been performed to study different impingement cooling schemes in static and rotating conditions. Geometry replicates a leading-edge cold bridge system, including a radial supply channel and five rows of film-cooling and showerhead holes. Two impingement geometries have been studied, with different numbers of holes and diameters but with equal overall passage area. Reynolds numbers up to 13,800 and rotation numbers up to 0.002 have been investigated (based on an equivalent slot width). Tests have been performed using a novel implementation of transient heat transfer technique, which allows correct replication of the sign of buoyancy forces by flowing ambient temperature air into a preheated test article. Results show that complex interactions occur between the different features of the system, with a particularly strong effect of jet supply condition. Rotation further interacts with these phenomena, generally leading to a slight decrease in heat transfer.

Heat Transfer Analysis Over a Film Cooled Platform of a Vane Cascade With a Non-Uniform Inlet Flow

2017 ◽  
Author(s):  
G. Barigozzi ◽  
S. Ravelli ◽  
H. Abdeh ◽  
A. Perdichizzi ◽  
M. Henze ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Film Cooling ◽  
Cooling System ◽  
Convective Heat Transfer Coefficient ◽  
Leading Edge ◽  
Heat Transfer Analysis ◽  
Flow Distortion ◽  
Inlet Flow ◽  
Inlet Flow Distortion

This paper reports on heat transfer measurements performed on the film cooled platform of a linear nozzle vane cascade, subject to non-uniform inlet flow conditions. An obstruction, installed upstream of the cascade at different tangential positions, was responsible for inlet flow distortion. The platform cooling system included both purge flow from a slot located upstream of the leading edge and coolant ejection from a row of cylindrical holes located upstream of the slot. Testing was performed at inlet Mach number of Ma1 = 0.12 with both slot and combustor holes blowing at nominal conditions. Measured values of adiabatic film cooling effectiveness on the platform were used to obtain a detailed map of the convective heat transfer coefficient. The final goal was to compute the net heat flux reduction (NHFR), due to film cooling, when varying the relative position between obstruction and airfoil. Aligning the inflow non uniformity with the vane leading edge leads to a detrimental increase in the heat flux into the platform, within the vane passage. Conversely, positive NHFR values are observed over most of the platform surface if the inlet flow distortion is moved toward the suction side of the adjacent vane.

Experimental Investigation on the Heat Transfer of a Leading Edge Cooling System: Effects of Jet-to-Jet Spacing and Showerhead Extraction

2013 ◽  
Author(s):  
Bruno Facchini ◽  
Francesco Maiuolo ◽  
Lorenzo Tarchi ◽  
Nils Ohlendorf
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Large Scale ◽  
Cooling System ◽  
Leading Edge ◽  
Test Facility ◽  
Cooling Flow ◽  
Nusselt Numbers ◽  
Circular Holes ◽  
Nusselt Number Distribution

An experimental survey of a leading edge cooling scheme was performed to measure the Nusselt number distribution on a large scale test facility simulating the leading edge cavity of a pressure turbine blade. Test section is composed by two adjacent cavities, a rectangular supply channel and the leading edge cavity. The cooling flow impinges on the concave leading edge internal walls, by means of an impingement array located between the two cavities, and it is extracted through shower-head and film cooling holes. The impingement geometry is composed of a double array of circular holes. The aim of the present study is to point out the effects on the heat transfer coefficient of the radial jet pitch (y/d = 3 to 5) and the tangential jet pitch (x/d = 3 to 5). Moreover the influence of the shower-head extraction on the heat transfer distribution is investigated. Measurements were performed by means of a transient technique using narrow band Thermo-chromic Liquid Crystals (TLC). Jet Reynolds number was varied in order to cover the typical engine conditions of these cooling systems (Rej = 15000–45000). Results are reported in terms of detailed 2D maps, radial and tangential averaged Nusselt numbers.

Numerical simulation of swirling flow effect on the first stage vane film cooling distribution

2016 ◽  
Vol 07 (03) ◽  
pp. 1650031
Author(s):  
Hong Yin
Keyword(s):  
Flow Field ◽  
Film Cooling ◽  
Swirling Flow ◽  
Cooling System ◽  
Leading Edge ◽  
Suction Side ◽  
Local Area ◽  
Swirl Flow ◽  
Flow Effect ◽  
Recirculation Flow

In advanced gas turbine technology, lean premixed combustion is an effective strategy to reduce peak temperature and thus, NO[Formula: see text] emissions. The swirler is adopted to establish recirculation flow zone, enhancing mixing and stabilizing the flame. Therefore, the swirling flow is dominant in the combustor flow field and has impact on the vane. This paper mainly investigates the swirling flow effect on the turbine first stage vane cooling system by conducting a group of numerical simulations. Firstly, the numerical methods of turbulence modeling using RANS and LES are compared. The computational model of one single swirl flow field is considered. Both the RANS and LES results give reasonable recirculation zone shape. When comparing the velocity distribution, the RANS results generally match the experimental data but fail to at some local area. The LES modeling gives better results and more detailed unsteady flow field. In the second step, the RANS modeling is incorporated to investigate the vane film cooling performance under the swirling inflow boundary condition. According to the numerical results, the leading edge film cooling is largely altered by the swirling flow, especially for the swirl core-leading edge aligned case. Compared to the pressure side, the suction side film cooling is more sensitive to the swirling flow. Locally, the film cooling jet is lifted and turned by the strong swirling flow.

Sign in / Sign up

Export Citation Format

Share Document