High-fidelity simulations of multi-jet impingement cooling flows

2021 ◽  
pp. 1-21
Author(s):  
Jose Javier Otero Perez ◽  
Richard Sandberg ◽  
Satoshi Mizukami ◽  
Koichi Tanimoto
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Cross Flow ◽  
Distance Effect ◽  
Jet Impingement ◽  
Impingement Cooling ◽  
Cooling Flows ◽  
Turbulent Inflow ◽  
The Cross ◽  
Flow Effects

Abstract This article shows the first parametric study on turbulent multi-jet impingement cooling flows using large-eddy simulations (LES). We focus on assessing the influence of the inter-jet distance and the cross-flow conditions on the heat transfer at the impingement wall. The LES setup is thoroughly validated with both experimental and direct numerical simulation data, showing an excellent agreement. The inter-jet distance effect on the heat transfer is studied comparing three different distances, where the full Nusselt number profile decreases in amplitude when the jet distance is increased. To evaluate the cross-flow effects, we prescribe both laminar and turbulent inflow conditions at different cross-flow magnitudes ranging between 20% and 40% of the impinging jet speed. Large cross-flow intensities cause a jet deflection which reduces the maxima in the Nusselt number distribution, and it increases the heat transfer in the areas of the wall less affected by the jet impingement. Adding realistic turbulent fluctuations to the inflow enhances the cross-flow effects on the heat transfer at the impingement wall.

High-Fidelity Simulations of Multi-Jet Impingement Cooling Flows

2020 ◽  
Author(s):  
J. Javier Otero-Pérez ◽  
Richard D. Sandberg ◽  
Satoshi Mizukami ◽  
Koichi Tanimoto
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Cross Flow ◽  
Distance Effect ◽  
Jet Impingement ◽  
Impingement Cooling ◽  
Cooling Flows ◽  
Turbulent Inflow ◽  
The Cross ◽  
Flow Effects

Abstract This article shows the first parametric study on turbulent multi-jet impingement cooling flows using large-eddy simulations (LES). We focus on assessing the influence of the inter-jet distance and the cross-flow conditions on the heat transfer at the impingement wall. The LES setup is thoroughly validated with both experimental and direct numerical simulation data, showing an excellent agreement. The inter-jet distance effect on the heat transfer is studied comparing three different distances, where the full Nusselt number profile decreases in amplitude when the jet distance is increased. To evaluate the cross-flow effects, we prescribe both laminar and turbulent inflow conditions at different cross-flow magnitudes ranging between 20% and 40% of the impinging jet speed. Large cross-flow intensities cause a jet deflection which reduces the maxima in the Nusselt number distribution, and it increases the heat transfer in the areas of the wall less affected by the jet impingement. Adding realistic turbulent fluctuations to the inflow enhances the cross-flow effects on the heat transfer at the impingement wall.

Effects of Extended Jet Holes to Heat Transfer and Flow Characteristics of the Jet Impingement Cooling

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Ahmet Ümit Tepe ◽  
Kamil Arslan ◽  
Yaşar Yetişken ◽  
Ünal Uysal
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Flat Surface ◽  
Flow Characteristics ◽  
Cross Flow ◽  
Jet Impingement ◽  
Target Surface ◽  
Impingement Cooling ◽  
Compressor Power

In this study, effects of extended jet holes to heat transfer and flow characteristics of jet impingement cooling were numerically investigated. Cross-flow in the impinging jet cooling adversely affects the heat transfer on the target surface. The main purpose of this study is to reduce the negative effect of cross-flow on heat transfer by extending jet holes toward the target surface with nozzles. This study has been conducted under turbulent flow condition (15,000 ≤ Re  ≤  45,000). The surface of the turbine blade, which is the target surface, has been modeled as a flat plate. The effect of the ribs, placed on the target surface, on the heat transfer has been also investigated, and the results were compared with the flat surface. The parameters such as average and local Nusselt numbers on the target surface, flow characteristics, and compressor power have been examined in detail. It was obtained from the numerical results that the average Nusselt number increases with decreasing the gap between the target surface and the nozzle. In addition, the higher average Nusselt number was obtained on the flat surface than the ribbed surface. The lowest compressor power was achieved in the 5Dj nozzle gap for the flat surface and in the 4Dj nozzle gap for the ribbed surface.

Investigations on the Heat Transfer and Flow Characteristics in a Trapezoid Duct for Turbine Blade Leading Edge

2018 ◽  
Author(s):  
Hai-yong Liu ◽  
Cun-liang Liu ◽  
Lin Ye
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Cross Flow ◽  
Side Wall ◽  
Swirl Flow ◽  
Transfer Enhancement ◽  
Impingement Cooling ◽  
Exit Side ◽  
Target Wall ◽  
The Cross

To evaluate the application of the impingement cooling in a trapezoidal duct, particularly the influence on internal cooling of the cross flow and swirl flow. Experimental and numerical studies have been performed. The experiment focuses on the heat transfer characteristics in the duct, when the numerical simulation focuses on the flow characteristics. Four Reynolds numbers (10000, 20000, 30000 and 40000), six cross flow mass flow ratios (0, 0.1, 0.2, 0.3, 0.4 and 0.5) and two impingement angle (35° and 45°) are considered in both the experiment and the numerical simulation. The temperature on the target wall and the exit side wall is measured by the thermocouples, when the realizable k-ε turbulence model and enhanced wall treatment are performed using a commercial code Fluent. The results show that only part of the jets contribute in the heat transfer enhancement on the target wall, the other jets improve a large anticlockwise vortex occupied the upper part of the duct and drive strong swirl flow. The heat transfer on the exit side wall is enhanced by the swirl flow. The cross flow is induced in the duct by the outflow of the end exit hole. It deflects the jets and abates the impingement cooling on the target wall in the downstream region but has no evidently effect on the heat transfer on the exit side wall. Higher impingement angle helps to augment the impingement cooling on the target wall and improves the resistance ability of the jets against the effect of the cross flow. The heat transfer enhancement ability on the target wall and exit side wall in the present duct is compared to that of a smooth duct. The Nusselt number of the former is about 3 times higher than that of the latter. It indicates that the impingement and swirl play equally important roles in the heat transfer enhancement in the present duct. Empirical dimensionless correlations based on the present experiment data are presented in the paper.

Numerical Study on Flow and Heat Transfer Characteristics of Jet Impingement Cooling

2011 ◽  
Vol 148-149 ◽  
pp. 680-683
Author(s):  
Run Peng Sun ◽  
Wei Bing Zhu ◽  
Hong Chen ◽  
Chang Jiang Chen
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Numerical Study ◽  
Cross Flow ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Transfer Characteristic ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Transfer Characteristics

Three-dimensional numerical study is conducted to investigate the heat transfer characteristics for the flow impingement cooling in the narrow passage based on cooling technology of turbine blade.The effects of the jet Reynolds number, impingement distance and initial cross-flow on heat transfer characteristic are investigated.Results show that when other parameters remain unchanged local heat transfer coefficient increases with increase of jet Reynolds number；overall heat transfer effect is reduced by initial cross-flow；there is an optimal distance to the best effect of heat transfer.

Effects of Nanoparticle Shape on Slot-Jet Impingement Cooling of a Corrugated Surface With Nanofluids

2017 ◽  
Vol 9 (2) ◽  
Author(s):  
Fatih Selimefendigil ◽  
Hakan F. Öztop
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Jet Impingement ◽  
Heat Transfer Characteristics ◽  
Impingement Cooling ◽  
Corrugated Surface ◽  
Nanoparticle Shapes

Numerical study of jet impingement cooling of a corrugated surface with water–SiO2 nanofluid of different nanoparticle shapes was performed. The bottom wall is corrugated and kept at constant surface temperature, while the jet emerges from a rectangular slot with cold uniform temperature. The finite volume method is utilized to solve the governing equations. The effects of Reynolds number (between 100 and 500), corrugation amplitude (between 0 and 0.3), corrugation frequency (between 0 and 20), nanoparticle volume fraction (between 0 and 0.04), and nanoparticle shapes (spherical, blade, brick, and cylindrical) on the fluid flow and heat transfer characteristics were studied. Stagnation point and average Nusselt number enhance with Reynolds number and solid particle volume fraction for both flat and corrugated surface configurations. An optimal value for the corrugation amplitude and frequency was found to maximize the average heat transfer at the highest value of Reynolds number. Among various nanoparticle shapes, cylindrical ones perform the best heat transfer characteristics in terms of stagnation and average Nusselt number values. At the highest solid volume concentration of the nanoparticles, heat transfer values are higher for a corrugated surface when compared to a flat surface case.

Effectiveness of Jet Impingement Cooling System on Convex Surface

2016 ◽  
Vol 819 ◽  
pp. 74-77
Author(s):  
Mohamad Nor Musa ◽  
Mohamad Faizal Fauzi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Coefficient ◽  
Convex Surface ◽  
Cooling System ◽  
Jet Impingement ◽  
Impingement Cooling ◽  
Reynolds Number Increase ◽  
Number Increase

Jet impingement is one of cooling method used in order to achieve high heat transfer coefficient and widely used in industry applications such as drying of textile and film, glass and plastic sheets, cooling of electronic equipment, and heat treatment of metals. In this research, it focused on the effectiveness of the jet impingement cooling system on the convex surface based on mass blowing rate and nozzle exit to surface parameters. The scope of experiment research encompasses are convex surface made of aluminum alloy and diameter 12.5cm. For mass blowing rate parameters, it use ʋjet = 1.98m/s, 3.03m/s, 4.97m/s and 6.00m/s which has Reynolds number range from 643 until 1946. Nozzle exit to surface distance,s/d = 4.0, 8.0 and 12.0. In this experiment model, a major components that involved are a compressor, nozzle, convex surface model, K thermocouple and heater. For the result of the experiment, it is based on the data obtain through a heat transfer coefficient and Nusselt number which the plotted graph focus on the space spacing and Reynolds number parameters. For the graph Nusselt number versus s/d at stagnation point c/d=0, it shown that when the Reynolds number increase, the Nusselt number also increase. In term of effectiveness, the s/d=12.0 has a good effectiveness jet impingement cooling system. For the graph of Nusselt number versus Reynolds at stagnation point, c/d=0, as Reynolds number increase, the Nusselt number increase too. From this experiment the better cooling effect is at Reynolds number, Re=1946. Thus, it can conclude that, effectiveness for jet impingement cooling system on the convex surface occurs at the highest Reynolds number.

Experimental and Numerical Study of Jet Impingement Cooling for Improved Gas Turbine Blade Internal Cooling With In-Line and Staggered Nozzle Arrays

2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Abdel Rahman Salem ◽  
Farah Nazifa Nourin ◽  
Mohammed Abousabae ◽  
Ryoichi S. Amano
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbine ◽  
Numerical Study ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Target Surface ◽  
Internal Cooling ◽  
Impingement Cooling ◽  
Gas Turbine Blades

Abstract Internal cooling of gas turbine blades is performed with the combination of impingement cooling and serpentine channels. Besides gas turbine blades, the other turbine components such as turbine guide vanes, rotor disks, and combustor wall can be cooled using jet impingement cooling. This study is focused on jet impingement cooling, in order to optimize the coolant flow, and provide the maximum amount of cooling using the minimum amount of coolant. The study compares between different nozzle configurations (in-line and staggered), two different Reynold's numbers (1500 and 2000), and different stand-off distances (Z/D) both experimentally and numerically. The Z/D considered are 3, 5, and 8. In jet impingement cooling, the jet of fluid strikes perpendicular to the target surface to be cooled with high velocity to dissipate the heat. The target surface is heated up by a direct current (DC) power source. The experimental results are obtained by means of thermal image processing of the captured infra-red (IR) thermal images of the target surface. Computational fluid dynamics (CFD) analysis were employed to predict the complex heat transfer and flow phenomena, primarily the line-averaged and area-averaged Nusselt number and the cross-flow effects. In the current investigation, the flow is confined along with the nozzle plate and two parallel surfaces forming a bi-directional channel (bi-directional exit). The results show a comparison between heat transfer enhancement with in-line and staggered nozzle arrays. It is observed that the peaks of the line-averaged Nusselt number (Nu) become less as the stand-off distance (Z/D) increases. It is also observed that the fluctuations in the stagnation heat transfer are caused by the impingement of the primary vortices originating from the jet nozzle exit.

Combination of Impingement and Trip Strips for Combustor Liner Backside Cooling

Volume 3 ◽  
2004 ◽  
Author(s):  
Ryan Hebert ◽  
Srinath V. Ekkad ◽  
Vivek Khanna
Keyword(s):  
Heat Transfer ◽  
Cross Flow ◽  
Jet Impingement ◽  
Reynolds Numbers ◽  
Combination Technique ◽  
Impingement Jet ◽  
Impingement Heat Transfer ◽  
Flow Effects ◽  
Heat Transfer Degradation ◽  
Cooling Air

Effective cooling of modern low NOx combustor liners is achieved through combinations of impingement and other heat transfer enhancement methods. In the present study, a combination of impingement and trip strips is studied to determine the optimum location of trip strips with respect to impingement jet arrays. Heat transfer with pure impingement has degradation downstream due to increased cross-flow effects. To counter the cross-flow induced heat transfer degradation, a combination technique wherein impingement is combined with ribs placed in between impingement rows or downstream of the impingement array is studied. Three configurations with increased rib placements and reduced impingement holes are studied and compared with pure impingement cases for the same jet Reynolds number. Three jet Reynolds numbers are studied for Rej = 10000, 20000, and 30000. Detailed heat transfer distributions are obtained using the transient liquid crystal technique. Results show that the presence of ribs increases jet impingement heat transfer on the surface with lower mass flows. The effectiveness of the combination ribs and impingement can provide higher heat transfer with reduced cooling air requirements.

Enhancement of Impingement Cooling in a High Cross Flow Channel Using Shaped Impingement Cooling Holes

2009 ◽  
Vol 132 (2) ◽  
Author(s):  
Andrew C. Chambers ◽  
David R. H. Gillespie ◽  
Peter T. Ireland ◽  
Robert Kingston
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Cross Flow ◽  
Target Surface ◽  
Impingement Cooling ◽  
Turbine Cooling ◽  
Impingement Jet ◽  
Coefficient Distribution ◽  
Cooling Passage ◽  
Experimental Rig

Impingement systems are common place in many turbine cooling applications. Generally these systems consist of a target plate that is cooled by the impingement of multiple orthogonal jets. While it is possible to achieve high target surface heat transfer with this configuration, the associated pressure drop is generally high and the cooling efficiency low. Furthermore, especially in large impingement arrays, the buildup of cross flow from upstream jets can be significant and results in deflection of downstream impingement jets reducing the resultant heat transfer coefficient distribution. This paper presents a computational and experimental investigation into the use of shaped elliptical or elongated circular impingement holes designed to improve the penetration of the impinging jet across the coolant passage. This is of particular interest where there is significant cross flow. Literature review and computational investigations are used to determine the optimum aspect ratio of the impingement jet. The improved heat transfer performance of the modified design is then tested in an experimental rig with varying degrees of cross flow at engine representative conditions. In all cases, a 16% increase in the Nusselt number on the impingement target surface in the downstream half of the cooling passage was achieved. Under the first four impingement holes, a Nusselt number enhancement of 28–77% was achieved, provided no additional cross flow was present in the passage. When appropriately aligned, a significant reduction in the stress concentration factor caused by the addition of a hole can be achieved using this design.

Heat Transfer and Fluid Flow of a Single Jet Impingement in Cross-Flow Modified by a Vortex Generator Pair

2016 ◽  
Author(s):  
Chenglong Wang ◽  
Lei Luo ◽  
Lei Wang ◽  
Bengt Sundén
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Gas Turbines ◽  
Cross Flow ◽  
Vortex Generator ◽  
Jet Impingement ◽  
Transfer Coefficients ◽  
Stagnation Region ◽  
Target Wall ◽  
The Cross

Jet impingement cooling is widely used in modern gas turbines. In the present study, both heat transfer and flow field measurements of jet impingement in cross-flow are carried out with and without a vortex generator pair (VGP). The jet and cross-flow Reynolds numbers are fixed at 15,000 and 48,000, respectively. The local heat transfer coefficients are obtained by a liquid crystal thermography (LCT) technique. Results show that the jet impingement heat transfer on the target wall is remarkably enhanced by the VGP as compared to the baseline case. The stagnation region moves upstream with improved heat transfer when the VGP is present. The flow field is measured by particle image velocimetry (PIV). The cross-flow is shown to deflect the impinging jet but the VGP reduces the streamwise momentum of the cross-flow and drives the crossflow away from the issuing jet. This leads to stronger jet impingement and thus heat transfer enhancement on the target wall.

Sign in / Sign up

Export Citation Format

Share Document