A Numerical and Experimental Study of the Time Averaged and Transient Flow Downstream of a Butterfly Valve

2021 ◽  
Author(s):  
Junyu Tao ◽  
Zhe Lin ◽  
Guang Zhang ◽  
Jingpan Su ◽  
Zuchao Zhu
Keyword(s):  
Experimental Study ◽  
Flow Separation ◽  
Velocity Fluctuation ◽  
Transient Flow ◽  
Flow Instability ◽  
Flow State ◽  
Butterfly Valve ◽  
Unstable Region ◽  
Valve Disc ◽  
Flow Situation

Abstract This research took the DN50 butterfly valve as the research object and studied the flow situation of butterfly valves with different shafts. The resistance characteristics, flow state, characteristics, and flow instability of butterfly valves with different structures were studied by experiments and numerical simulations. Research shows that the edge of the valve disc occurs flow separation, and the drag of the valve disc fluctuates non-periodically with time. Under different opening degrees, the velocity distribution downstream of the valve varies, and the effect of the shaft on the velocity fluctuation is different. Finally, the unstable region of flow downstream of the valve is determined. This study provides a reference for the use and optimization of butterfly valves.

EXPERIMENTAL STUDY OF GAS-LIQUID FLOW SEPARATION

2016 ◽  
Author(s):  
Yasmin Gavioli ◽  
Valter Aibe ◽  
Juliana Loureiro ◽  
Atila Pantaleão Silva Freire
Keyword(s):  
Experimental Study ◽  
Liquid Flow ◽  
Flow Separation ◽  
Gas Liquid Flow

Compressible Flowfield Characteristics of Butterfly Valves

1989 ◽  
Vol 111 (4) ◽  
pp. 400-407 ◽  
Author(s):  
M. J. Morris ◽  
J. C. Dutton
Keyword(s):  
Flow Separation ◽  
Pressure Ratio ◽  
Disk Surface ◽  
Surface Flow ◽  
Operating Conditions ◽  
Local Geometry ◽  
Operating Pressure ◽  
Butterfly Valve ◽  
Pressure Distributions ◽  
Flow Separation And Reattachment

The results of an experimental investigation into the flowfield characteristics of butterfly valves under compressible flow operating conditions are reported. The experimental results include Schlieren and surface flow visualizations and flowfield static pressure distributions. Two valve disk shapes have been studied in a planar, two-dimensional test section: a generic biconvex circular arc profile and the midplane cross-section of a prototype butterfly valve. The valve disk angle and operating pressure ratio have also been varied in these experiments. The results demonstrate that under certain conditions of operation the butterfly valve flowfield can be extremely complex with oblique shock waves, expansion fans, and regions of flow separation and reattachment. In addition, the sensitivity of the valve disk surface pressure distributions to the local geometry near the leading and trailing edges and the relation of the aerodynamic torque to flow separation and reattachment on the disk are shown.

scholarly journals Model-Based Analysis of Flow Separation Control in a Curved Diffuser by a Vibration Wall

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1781
Author(s):  
Weiyu Lu ◽  
Xin Fu ◽  
Jinchun Wang ◽  
Yuanchi Zou
Keyword(s):  
Flow Field ◽  
Flow Control ◽  
Flow Separation ◽  
Vibration Frequency ◽  
Flow Instability ◽  
Control Technique ◽  
Simplified Model ◽  
Main Stream ◽  
Control Performance ◽  
Flow Separation Control

Vibration wall control is an important active flow control technique studied by many researchers. Although current researches have shown that the control performance is greatly affected by the frequency and amplitude of the vibration wall, the mechanism hiding behind the phenomena is still not clear, due to the complex interaction between the vibration wall and flow separation. To reveal the control mechanism of vibration walls, we propose a simplified model to help us understand the interaction between the forced excitation (from the vibration wall) and self-excitation (from flow instability). The simplified model can explain vibration wall flow control behaviors obtained by numerical simulation, which show that the control performance will be optimized at a certain reduced vibration frequency or amplitude. Also, it is shown by the analysis of maximal Lyapunov exponents that the vibration wall is able to change the flow field from a disordered one into an ordered one. Consistent with these phenomena and bringing more physical insight, the simplified model implies that the tuned vibration frequency and amplitude will lock in the unsteady flow separation, promote momentum transfer from the main stream to the separation zone, and make the flow field more orderly and less chaotic, resulting in a reduction of flow loss.

scholarly journals Simulation and Experimental Investigation of the Stay Vane Channel Flow in a Reversible Pump Turbine at Off-Design Conditions

2017 ◽  
Vol 61 (2) ◽  
pp. 94 ◽  
Author(s):  
Sandro Erne ◽  
Gernot Edinger ◽  
Anton Maly ◽  
Christian Bauer
Keyword(s):  
Transient Flow ◽  
Guide Vane ◽  
Low Frequency ◽  
Rotating Stall ◽  
Design Flow ◽  
Flow State ◽  
Mean Flow ◽  
Load Range ◽  
Pump Turbine ◽  
Stall Inception

This work presents the assessment of the mean flow field and low frequency disturbances in the stay vane channel of a model pump turbine using transient numerical simulations and LDV-based measurements. The focus is laid on transient CFD simulations of characteristic flow states in the stay vane channel when operating at off-design conditions in pump mode. Experimental and numerical investigations obtained a shifting velocity distribution between the shroud and hub of the distributor when continuously increasing the discharge in the part-load range. Simulations captured the occurrence of this changing flow state in the stay vane channel reasonably well. A further increase of the discharge showed a uniformly redistributed mean flow of both hub and shroud side. Monitoring points and integral quantities from measurements and transient simulations were used to interpret the development of transient flow patterns in the stay vane channel at the operating point of strongest asymmetrical flow. During simulation and measurement, a dominant rotating stall inception was observed near the design flow of the pump turbine. At this point where the stall becomes severe, a high level of correlation between the signals of the upper and lower stalled flow in the stay vane channel was calculated. Further simulations for different guide vane positions predicted a strong influence of the guide vane position on the structure of rotating stall.

Influence of Inlet Velocity Condition on Unsteady Flow Characteristics in Piping With a Short-Elbow at High Reynolds Number Condition

2014 ◽  
Author(s):  
Ayako Ono ◽  
Masaaki Tanaka ◽  
Jun Kobayashi ◽  
Hideki Kamide
Keyword(s):  
Reynolds Number ◽  
Flow Separation ◽  
Velocity Fluctuation ◽  
Complex Geometry ◽  
Perforated Plate ◽  
Secondary Flows ◽  
Curvature Radius ◽  
Mean Velocity ◽  
Inlet Velocity ◽  
Velocity Condition

In design of the Japan Sodium-cooled Fast Reactor (JSFR), mean velocity of the coolant is approximately 9 m/s in the primary hot leg (H/L) piping which diameter is 1.27 m. The Reynolds number in the H/L piping reaches 4.2×107. Moreover, a short-elbow which has Rc/D = 1.0 (Rc: Curvature radius, D: Pipe diameter) is used in the hot leg piping in order to achieve compact plant layout and reduce plant construction cost. In the H/L piping, flow-induced vibration (FIV) is concerned due to excitation force which is caused by pressure fluctuation on the wall closely related with the velocity fluctuation in the short-elbow. In the previous study, relation between the flow separation and the pressure fluctuations in the short-elbow was revealed under the specific inlet condition with flat distribution of time-averaged axial velocity and relatively weak velocity fluctuation intensity in the pipe. However, the inlet velocity condition of the H/L in a reactor may have ununiformed profile with highly turbulent due to the complex geometry in reactor vessel (R/V). In this study, the influence of the inlet velocity condition on unsteady characteristics of velocity in the short-elbow was studied. Although the flow around the inlet of the H/L in R/V could not simulate completely, inlet velocity conditions were controlled by installing the perforated plate with plugging the flow-holes appropriately. Then expected flow patterns were made at 2D upstream position from the elbow inlet in the experiments. It was revealed that the inlet velocity profiles affected circumferential secondary flow and the secondary flows affected an area of flow separation at the elbow, by local velocity measurement by the PIV (particle image velocimetry). And it was found that the low frequent turbulence in the upstream piping remained downstream of the elbow though their intensity was attenuated.

Sign in / Sign up

Export Citation Format

Share Document