Performance, combustion, and emission evaluation of ethanol-gasoline blends ignited by diesel in dual-fuel intelligent charge compression ignition (ICCI) engine

2021 ◽  
pp. 1-21
Author(s):  
Yaoyuan Zhang ◽  
Wenbin Zhao ◽  
Haoqing Wu ◽  
Zhuoyao He ◽  
Yong Qian ◽  
...  
Keyword(s):  
High Efficiency ◽  
Carbon Chain ◽  
Dual Fuel ◽  
Carbon Chain Length ◽  
Injection Timing ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Pure Ethanol ◽  
Wide Range ◽  
Homogeneous Combustion

Abstract A recent proposed dual-fuel combustion mode, intelligent charge compression ignition (ICCI), realizes the high-efficiency and clean combustion by organizing continuous stratification in a wide range of engine load. The paper investigated the performance of alcohol blended gasoline as low reactivity fuel (LRF) in ICCI combustion mode. Pure ethanol named E100 was also tested as LRF for comparison. To emphasize the differences of LRF properties and exclude the effect of the heat release phasing, the diesel injection timing was adjusted to maintain the same combustion phasing (CA50) at various LRF ratios under medium load. The results showed that E100 and E85 (ethanol ratio in gasoline-ethanol blend) promoted the degree of homogeneous combustion and eradicated soot emissions despite a slight increase of NOx. The maximum indicated thermal efficiency (ITE) was over 51.1% using E85, followed by 50.5% of E50. The perfect substitution ratio at the maximum ITE decreased from more than 80% to about 65% when increasing the ethanol ratio in LRF from 10% to 100%. The unregulated emissions such as aldehydes, ethylene, and methane, produced from incomplete combustion of ethanol were inhabited by E85, while the formation of toluene attributed to the appropriate carbon chain length of gasoline diminished when using E85 and E100.

scholarly journals Effects of pre-injection strategy on combustion performance of methanol/diesel dual fuel engine at low load

2021 ◽  
Vol 252 ◽  
pp. 02027
Author(s):  
Junheng Liu ◽  
Pengcheng Wu ◽  
Lejian Wang ◽  
Demin Jia ◽  
Qian Ji ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Factors Affecting ◽  
Emission Performance ◽  
Low Load ◽  
Peak Value

In this paper, the effect of pre-injection timing on the combustion and emission performance of methanol/diesel high premixed charge compression ignition (HPCCI) combustion mode at low load was studied by three-dimensional numerical simulation. The simulation is carried out under the conditions of 1900 r/min and 25% load, and the pre-injection diesel mass remains constant and the pre-injection timing is changed under the conditions of 50% and 60% methanol ratio respectively. The results show that with the delay of pre-injection timing, the evaporation of pre-injected fuel in cylinder becomes faster, the low temperature reaction is enhanced, and the peak value of heat release rate is higher. In addition, the distribution of pre-injected diesel in cylinder and the position of impact wall are the important factors affecting the combustion and emission performance in cylinder, and when the injection timing is -35 °CA ATDC, the combustion and emission characteristics of the engine are optimal. Finally, by comparing with the traditional RCCI combustion mode, the enhancement ability of HPCCI combustion mode on methanol combustion efficiency under low load is verified and analyzed.

An experimental study of the injection strategies on engine performance of the butanol/biodiesel dual-fuel Intelligent Charge Compression Ignition mode

2020 ◽  
pp. 146808742096399
Author(s):  
Wenbin Zhao ◽  
Yaoyuan Zhang ◽  
Guan Huang ◽  
Zilong Li ◽  
Yong Qian ◽  
...  
Keyword(s):  
Heat Release ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Low Levels ◽  
Injection Strategies

Intelligent Charge Compression Ignition (ICCI) combustion mode is a novel dual-fuel combustion strategy that has been proposed recently. In ICCI combustion mode, two fuels with different reactivity are directly injected during the intake stroke and compression stroke, respectively, to achieve flexible reactivity gradient and equivalence ratio stratification. In this study, experiments were conducted on a single-cylinder diesel engine to investigate the effects of butanol direct injection strategies on the engine running with ICCI combustion mode at a constant speed of 1500 r/min and medium load. Results showed that ICCI combustion mode was composed of premixed heat release and diffusion heat release. In compare, the percentage of premixed heat release was higher than the diffusion heat release. With fixed biodiesel direct injection timing (SOI2), retarding butanol single injection timing (SOI1) would delay combustion phasing while not distinctively affect ignition timing. SOI1 showed significant effect on the thermal efficiency and engine emissions. Indicated thermal efficiency (ITE) decreased at first and then slightly increased with retarding of SOI1, while the nitrogen oxides (NOx) emissions were always at low levels. As the butanol second direct injection timing (SOI1-2) retard and the corresponding energy ratio increase, more butanol entered into the crevice/squish regions, leading to the increase of unburned hydrocarbon (HC) and carbon monoxide (CO) emissions. EGR strategy helps to significantly reduce NOx emissions without affecting ITE although penalized HC and CO emissions are resulted in. The optimum butanol direct injection strategies were butanol single direct injection, especially in the early SOI1, in which the thermal efficiency was higher and emissions were at very low levels (NOx  < 0.4 g/kW h).

scholarly journals Octane Index Applicability over the Pressure-Temperature Domain

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 607
Author(s):  
Tommy R. Powell ◽  
James P. Szybist ◽  
Flavio Dal Forno Chuahy ◽  
Scott J. Curran ◽  
John Mengwasser ◽  
...  
Keyword(s):  
High Efficiency ◽  
National Laboratory ◽  
Operating Conditions ◽  
Dominant Factor ◽  
Compression Ignition ◽  
Oak Ridge ◽  
Operating Modes ◽  
Wide Range ◽  
Thermodynamic Conditions ◽  
Si Engines

Modern boosted spark-ignition (SI) engines and emerging advanced compression ignition (ACI) engines operate under conditions that deviate substantially from the conditions of conventional autoignition metrics, namely the research and motor octane numbers (RON and MON). The octane index (OI) is an emerging autoignition metric based on RON and MON which was developed to better describe fuel knock resistance over a broader range of engine conditions. Prior research at Oak Ridge National Laboratory (ORNL) identified that OI performs reasonably well under stoichiometric boosted conditions, but inconsistencies exist in the ability of OI to predict autoignition behavior under ACI strategies. Instead, the autoignition behavior under ACI operation was found to correlate more closely to fuel composition, suggesting fuel chemistry differences that are insensitive to the conditions of the RON and MON tests may become the dominant factor under these high efficiency operating conditions. This investigation builds on earlier work to study autoignition behavior over six pressure-temperature (PT) trajectories that correspond to a wide range of operating conditions, including boosted SI operation, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). A total of 12 different fuels were investigated, including the Co-Optima core fuels and five fuels that represent refinery-relevant blending streams. It was found that, for the ACI operating modes investigated here, the low temperature reactions dominate reactivity, similar to boosted SI operating conditions because their PT trajectories lay close to the RON trajectory. Additionally, the OI metric was found to adequately predict autoignition resistance over the PT domain, for the ACI conditions investigated here, and for fuels from different chemical families. This finding is in contrast with the prior study using a different type of ACI operation with different thermodynamic conditions, specifically a significantly higher temperature at the start of compression, illustrating that fuel response depends highly on the ACI strategy being used.

Optimization of piston bowl and valve system in compression ignition engine fueled with gasoline/diesel/polyoxymethylene dimethyl ethers for high efficiency

2019 ◽  
pp. 146808741986538
Author(s):  
Bowen Li ◽  
Haoye Liu ◽  
Linjun Yu ◽  
Zhi Wang ◽  
Jianxin Wang
Keyword(s):  
Heat Transfer ◽  
Thermal Efficiency ◽  
High Efficiency ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Compression Ignition Engine ◽  
Valve System ◽  
Percentage Points ◽  
Polyoxymethylene Dimethyl Ethers ◽  
Variable Valve

Polyoxymethylene dimethyl ethers, with excellent volatility and oxygen content of up to 49%, have great potential to improve engine performance and emission characteristics. In this study, experiments were carried out in a single-cylinder engine fueled with gasoline/diesel/polyoxymethylene dimethyl ethers blend fuel using multiple premixed compression ignition combustion mode along with engine optimization to exploit the high-efficiency potential. The thermal efficiency was increased by 9.4 percentage points after transforming the combustion mode from conventional diesel mode to gasoline/diesel/polyoxymethylene dimethyl ethers multiple premixed compression ignition mode. A fully variable valve system and a redesigned low-heat-transfer piston were used to further improve the thermal efficiency. The low-heat-transfer piston had a 15% lower area–volume ratio compared with the original ω-type piston. By replacing the original ω-type piston with the low-heat-transfer piston, the heat transfer loss was reduced by 2.29 percentage points and thus indicated thermal efficiency could be increased by 2.37 percentage points, which was up to 50.03%. On the basis of the low-heat-transfer piston, indicated thermal efficiency could be further increased to 51.09% with the application of fully variable valve system due to the longer ignition delay and more premixed combustion. At the same time, NOX emissions could be controlled below 0.4 g/kW·h using high exhaust gas recirculation ratio, which equaled the NOX emission limit of Euro VI standard. Although soot emissions could be increased due to weak turbulence and insufficient intake charge using the low-heat-transfer piston and fully variable valve system, it was still lower than those of the original diesel engines.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

scholarly journals Combustion stability control of gasoline compression ignition (GCI) under low-load conditions: A review

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Leilei Liu ◽  
Zhifa Zhang ◽  
Yue Liang ◽  
Fan Zhang ◽  
Binbin Yang
Keyword(s):  
High Efficiency ◽  
Stability Control ◽  
Combustion Stability ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Combustion Mode ◽  
Low Load ◽  
Temperature Combustion ◽  
Future Work ◽  
Load Conditions

Abstract With greater energy pressure and stricter emission standards, increasing power output and reducing emissions of engines are simultaneously required. To achieve this, considerable researches are motivated. In recent years, key and representative developments in the field of high-efficiency and clean engines have been carried out. Among them, a low temperature combustion concept called gasoline compression ignition (GCI) is widely considered by universities and research institutions around the world, since it has the potential to achieve ultra-low NO X and soot emissions while maintaining high thermal efficiency. However, GCI combustion mode has certain issues to be solved, such as combustion instability under low-load conditions. Therefore, this paper reviews the experimental, computational and optical studies on the combustion stability control of GCI combustion mode during low loads and describes the recent progress to improve combustion stability as well as points out the future work finally.

scholarly journals Effect of hydrogen peroxide addition to methane fueled homogeneous charge compression ignition engines through numerical simulations

2017 ◽  
Author(s):  
Zachary M. Hammond ◽  
John Hunter Mack ◽  
Robert W. Dibble
Keyword(s):  
Hydrogen Peroxide ◽  
Homogeneous Charge Compression Ignition ◽  
Injection Timing ◽  
Compression Ignition ◽  
Aqueous Hydrogen Peroxide ◽  
Compression Ignition Engine ◽  
Compression Ignition Engines ◽  
Wide Range ◽  
Phasing Control ◽  
Homogeneous Charge

The effect of the direct injection of hydrogen peroxide into a port-injected methane fueled homogeneous charge compression ignition engine was investigated numerically. The injection of aqueous hydrogen peroxide was implemented as a means of combustion phasing control. A single cylinder homogeneous charge compression ignition engine (2.43 L Caterpillar) was modeled using the Cantera 2.0 flame code toolkit, the GRI-Mech 3.0 chemical reaction mechanism, and a single-zone slider-crank engine model. Start of injection timing and the amount of injected hydrogen peroxide were manipulated to achieve desired combustion phasing under a wide range of intake temperatures. As the concentration of hydrogen peroxide is increased, the combustion phasing is advanced up to 22 degrees for the conditions investigated in this study. This advancing effect is most pronounced at small concentrations (&lt; 10 g H2O2 / kg CH4) and early injection timings (SOI &lt; 25 degrees BTDC). The model suggests hydrogen peroxide can be introduced as a means of combustion phasing control while maintaining the low emissions and peak in-cylinder pressures inherent in homogeneous charge compression ignition engines.

Effects of N-Butanol Content on the Dual-Fuel Combustion Mode With CNG at Two Engine Speeds

2018 ◽  
Author(s):  
Xiangyu Meng ◽  
Wuqiang Long ◽  
Yihui Zhou ◽  
Mingshu Bi ◽  
Chia-Fon F. Lee
Keyword(s):  
Thermal Efficiency ◽  
Engine Speed ◽  
Direct Injection ◽  
Fuel Combustion ◽  
Dual Fuel ◽  
Combustion Mode ◽  
Start Of Injection ◽  
Wide Range ◽  
Pilot Fuel ◽  
Dual Fuel Combustion

Because of the potential to reduce NOx and PM emissions simultaneously and the utilization of biofuel, diesel/compressed natural gas (CNG) dual-fuel combustion mode with port injection of CNG and direct injection of diesel has been widely studied. While in comparison with conventional diesel combustion mode, the dual-fuel combustion mode generally leads lower thermal efficiency, especially at low and medium load, and higher carbon monoxide (CO) and total hydrocarbons (THC) emissions. In this work, n-butanol was blended with diesel as the pilot fuel to explore the possibility to improve the performance and emissions of dual-fuel combustion mode with CNG. Various pilot fuels of B0 (pure diesel), B10 (90% diesel/10% n-butanol by volume basis), B20 (80% diesel/20% n-butanol) and B30 (70% diesel/30% n-butanol) were compared at the CNG substitution rate of 70% by energy basis under the engine speeds of 1400 and 1800 rpm. The experiments were carried out by sweeping a wide range of pilot fuel start of injection timings based on the same total input energy including pilot fuel and CNG. As n-butanol was added into the pilot fuel, the pilot fuel/CNG/air mixture tends to be more homogeneous. The results showed that for the engine speed of 1400 rpm, pilot fuel with n-butanol addition leads to a slightly lower indicated thermal efficiency (ITE). B30 reveals much lower NOx emission and slightly higher THC emissions. For the engine speed of 1800 rpm, B20 can improve ITE and decrease the NOx and THC emissions simultaneously relative to B0.

Sign in / Sign up

Export Citation Format

Share Document