Preliminary Investigation of Dilution Strategies to Control Engine Torque During Transient Events

2001 ◽  
Author(s):  
R. D. Maugham ◽  
N. D. Vaughan ◽  
C. J. Brace ◽  
S. W. Murray
Keyword(s):  
Gasoline Engine ◽  
Fuel Efficiency ◽  
Preliminary Investigation ◽  
Torque Control ◽  
Test Program ◽  
Lean Burn ◽  
Engine Torque ◽  
Variable Transmission ◽  
Transient Events ◽  
Initial Results

Abstract A continuously variable transmission (CVT) allows a powertrain controller the freedom to develop a required output power at a range of engine torque and speed conditions. This flexibility can be used to maximise fuel efficiency. Due to low frictional and pumping losses a gasoline engine’s fuel efficiency is maximised at low speed, high torque conditions. However due to the reduced torque margin available, controlling a gasoline engine in this region compromises transient vehicle response. Dilution torque control, using EGR or lean burn, has the potential to maintain the economy gains available using a CVT powertrain whilst improving a vehicle’s driveability. This paper introduces preliminary work that has been undertaken to investigate the potential of charge dilution to control steady state engine torque. A test rig has been developed based around an engine fitted with variable cam phasing and an external EGR system. The paper contains a discussion of initial results of a lean dilution test program used to demonstrate the principle.

scholarly journals Advancements in mechanical engineering spell hopeful development of autonomous biobots

2019 ◽  
Author(s):  
Aris Triwiyatno ◽  
Sumardi Sumardi
Keyword(s):  
Fuzzy Logic ◽  
Fuel Consumption ◽  
Gasoline Engine ◽  
Control Process ◽  
Engine Performance ◽  
Complex Problem ◽  
Torque Control ◽  
Reduce Fuel Consumption ◽  
Inference System ◽  
Engine Torque

In the case of injection gasoline engine, or better known as spark ignition engines, an effort to improve engine performance as well as to reduce fuel consumption is a fairly complex problem. Generally, engine performance improvement efforts will lead to increase in fuel consumption. However, this problem can be solved by implementing engine torque control based on intelligent regulation such as the fuzzy logic inference system. In this study, fuzzy logic engine torque regulation is used to control the throttle position entered by the driver to achieve optimal engine torque. An engine torque vs. throttle position and engine speed mapping for vehicles with economical function is used to build this control process regulation. From the simulation result, it can be concluded that this control strategy is very effective to reduce fuel consumption and simultaneously to optimize the engine performance.

TWC-SCR Aftertreatment System Evaluation for a Lean Burn Gasoline Engine Operating in HCCI, SACI, and SI Combustion Modes

2016 ◽  
Author(s):  
Jordan Easter ◽  
Stanislav V. Bohac
Keyword(s):  
Conversion Efficiency ◽  
Gasoline Engine ◽  
Fuel Efficiency ◽  
Compression Ignition ◽  
Scr Catalyst ◽  
Advanced Combustion ◽  
Nox Conversion ◽  
Combustion Modes ◽  
Scr System ◽  
Nox Conversion Efficiency

Low temperature and dilute Homogenous Charge Compression Ignition (HCCI) and Spark Assisted Compression Ignition (SACI) can improve fuel economy and reduce engine-out NOx emissions to very low values, often less than 30 ppm. However, these combustion modes are unable to achieve stringent future regulations such as SULEV 30 without the use of lean aftertreatment. Though active selective catalytic reduction (SCR) with urea injection and lean NOx traps (LNT) have been investigated as options for lean gasoline engines, a passive TWC-SCR system is investigated in this work because it avoids the urea storage and dosing hardware of a urea SCR system, and the high precious metal cost of an LNT. The TWC-SCR concept uses periodic rich operation to produce NH3 over a TWC to be stored on an SCR catalyst for subsequent NOx conversion during lean operation. In this work a laboratory study was performed with a modified 2.0 L gasoline engine that was cycled between lean HCCI and rich SACI operation, or between lean and rich SI (spark ignited) combustion, to evaluate NOx conversion and reduced fuel consumption. Different lambda values during rich operation and different times held in rich operation were investigated. Results are compared to a baseline case in which the engine is always operated at stoichiometric conditions. SCR system simulations are also presented that compare system performance for different levels of stored NH3. With the configuration used in this study, lean/rich HCCI/SACI operation showed a maximum NOx conversion efficiency of 10%, while lean/rich SI operation showed a maximum NOx conversion efficiency of 60%. However, if the low conversion efficiency of lean/rich HCCI/SACI operation could be improved through higher brick temperatures or additional SCR bricks, simulation results indicate TWC-SCR aftertreatment has the potential to provide near-zero SCR-out NOx concentration and increased system fuel efficiency. In these simulations, fuel efficiency improvement relative to stoichiometric SI were 7 to15% for lean/rich HCCI/SACI with zero tailpipe NOx and −1 to 5% for lean/rich SI with zero tailpipe NOx emissions. Although previous work indicated increased time for NH3 to start forming over the TWC during rich operation, less NH3 production over the TWC per fuel amount, and increased NH3 slip over the SCR catalyst for advanced combustion systems, if NOx conversion efficiency could be enhanced, improvements in fuel economy and low engine-out NOx from advanced combustion modes would more than make up for these disadvantages.

Tumble Flow Measurements Using Three Different Methods and Its Effects on Fuel Economy and Emissions

2006 ◽  
Author(s):  
Myoungjin Kim ◽  
Sihun Lee ◽  
Wootae Kim
Keyword(s):  
Fuel Economy ◽  
High Performance ◽  
Gasoline Engine ◽  
Exhaust Emissions ◽  
Combustion Stability ◽  
Lean Burn ◽  
Flow Measurements ◽  
Part Load ◽  
Gasoline Engines ◽  
Dynamometer Test

In-cylinder flows such as tumble and swirl have an important role on the engine combustion efficiencies and emission formations. In particular, the tumble flow, which is dominant in-cylinder flow in current high performance gasoline engines, has an important effect on the fuel consumptions and exhaust emissions under part load conditions. Therefore, it is important to know the effect of the tumble ratio on the part load performance and optimize the tumble ratio of a gasoline engine for better fuel economy and exhaust emissions. First step in optimizing a tumble flow is to measure a tumble ratio accurately. In this research the tumble flow was measured, compared and correlated using three different measurement methods: steady flow rig, 2-Dimensional PIV, and 3-Dimensional PTV. Engine dynamometer test was performed to find out the effect of the tumble ratio on the part load performance. Dynamometer test results of high tumble ratio engine showed faster combustion speed, retarded MBT timing, higher exhaust emissions, and a better lean burn combustion stability. Lean limit of the baseline engine was expanded from A/F=18:1 to A/F=21:1 by increasing a tumble ratio using MTV.

The Research of Lean Combustion Characteristic of Compound Injection System of Direct Injection Engine

2014 ◽  
Vol 532 ◽  
pp. 362-366 ◽  
Author(s):  
Jiang Feng Mou ◽  
Rui Qing Chen ◽  
Yi Wei Lu
Keyword(s):  
Gasoline Engine ◽  
Direct Injection ◽  
Injection System ◽  
Intake Manifold ◽  
Combustion Characteristic ◽  
Injection Timing ◽  
Mixed Gas ◽  
Lean Burn ◽  
Direct Injection Engine ◽  
Lean Combustion

This paper studies the lean burn limit characteristic of the compound injection system of the direct-injection gasoline engine. The low pressure nozzle on the intake manifold can achieve quality homogeneous lean mixture, and the direct injection in the cylinder can realized the dense mixture gas near the spark plug. By adjusting the two injection timing and injection quantity, and a strong intake tumble flow with special shaped combustion chamber, it can produces the reverse tumble to form different hierarchical levels of mixed gas in the cylinder. Experimental results show: the compound combustion system to the original direct-injection engine lean burn limit raise 1.8-2.5 AFR unit.

Optimization of Mode Switching Timing Control for a Lean-Burn Gasoline Engine With a Prototype Passive SCR System

2018 ◽  
Author(s):  
Dakota Strange ◽  
Pingen Chen ◽  
Vitaly Y. Prikhodko ◽  
James E. Parks
Keyword(s):  
Gasoline Engine ◽  
Nox Reduction ◽  
Cost Effective ◽  
Nox Storage ◽  
Mode Switching ◽  
Timing Control ◽  
Lean Burn ◽  
Gasoline Engines ◽  
Effective Manner ◽  
Passive Scr

Passive selective catalytic reduction (SCR) has emerged as a promising NOx reduction technology for highly-efficient lean-burn gasoline engines to meet stringent NOx emission regulation in a cost-effective manner. In this study, a prototype passive SCR which includes an upstream three-way catalyst (TWC) with added NOx storage component, and a downstream urealess SCR catalyst, was investigated. Engine experiments were conducted to investigate and quantify the dynamic NOx storage/release behaviors as well as dynamic NH3 generation behavior on the new TWC with added NOx storage component. Then, the lean/rich mode-switching timing control was optimized to minimize the fuel penalty associated with passive SCR operation. Simulation results show that, compared to the baseline mode-switching timing control, the optimized control can reduce the passive SCR-related fuel penalty by 6.7%. Such an optimized mode-switching timing control strategy is rather instrumental in realizing significant fuel efficiency benefits for lean-burn gasoline engines coupled with cost-effective passive SCR systems.

Research on Dynamic Torque Control Strategy for Parallel Hybrid Electric Vehicle

2011 ◽  
Vol 228-229 ◽  
pp. 951-956 ◽  
Author(s):  
Yun Bing Yan ◽  
Fu Wu Yan ◽  
Chang Qing Du
Keyword(s):  
Electric Vehicle ◽  
Hybrid Electric Vehicle ◽  
Control Algorithm ◽  
Dynamic Control ◽  
Torque Control ◽  
Engine Torque ◽  
Parallel Hybrid Electric Vehicle ◽  
Torque Control Strategy ◽  
Parallel Hybrid ◽  
Hybrid Electric

It is necessary for Parallel Hybrid Electric Vehicle (PHEV) to distribute energy between engine and motor and to control state-switch during work. Aimed at keeping the total torque unchanging under state-switch, the dynamic torque control algorithm is put forward, which can be expressed as motor torque compensation for engine after torque pre-distribution, engine speed regulation and dynamic engine torque estimation. Taking Matlab as the platform, the vehicle control simulation model is built, based on which the fundamental control algorithm is verified by simulation testing. The results demonstrate that the dynamic control algorithm can effectively dampen torque fluctuations and ensures power transfer smoothly under various state-switches.

Sign in / Sign up

Export Citation Format

Share Document