scholarly journals Advanced Labyrinth Seal Design Performance for High Pressure Ratio Gas Turbines

1975 ◽  
Author(s):  
H. L. Stocker
Keyword(s):  
High Pressure ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Labyrinth Seal ◽  
Internal Cavity ◽  
Water Tunnel ◽  
High Pressure Ratio ◽  
Test And Evaluation ◽  
Seal Design ◽  
Dynamic Seal

Labyrinth seal air leakage performance in current and advanced high pressure ratio gas turbines is directly related to the limitations of current available sealing technology. Sea design technology has not kept pace with the gas turbine major component advances. Therefore, an investigation was undertaken to design, fabricate and test several unique labyrinth seal concepts intended to decrease leakage through higher efficiency. The approach used in the unique designs for improving the efficiency of labyrinth seals involved increasing the internal cavity turbulence of the seal. The program involved three test and evaluation phases: (a) water tunnel studies; (b) static air rig tests; and (c) dynamic air rig tests. The water tunnel rig provided an economical method of screening the unique candidate designs. The most promising configurations from the water rig were fabricated and tested in the static air rig. Those configurations demonstrating a significant reduction in seal leakage over current designs were tested dynamically up to 786 ft/sec in an air rig to assess the effects of rotation. The results of this program effort show that each of the unique seal designs achieved lower leakage rates than a standard baseline step seal. In addition the dynamic seal test results show minimal effect on leakage due to rotation up to 786 ft/sec.

Design Study of an Advanced Concept Simple Gas Turbine for Possible Use in Low Emission Automobiles

1972 ◽  
Author(s):  
H. C. Eatock ◽  
M. D. Stoten
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Simple Cycle ◽  
Turbine Engines ◽  
Nox Emissions ◽  
Preliminary Design ◽  
Gas Turbine Engines ◽  
High Pressure Ratio

United Aircraft Corporation studied the potential costs of various possible gas turbine engines which might be used to reduce automobile exhaust emissions. As part of that study, United Aircraft of Canada undertook the preliminary design and performance analysis of high-pressure-ratio nonregenerated (simple cycle) gas turbine engines. For the first time, high levels of single-stage component efficiency are available extending from a pressure ratio less than 4 up to 10 or 12 to 1. As a result, the study showed that the simple-cycle engine may provide satisfactory running costs with significantly lower manufacturing costs and NOx emissions than a regenerated engine. In this paper some features of the preliminary design of both single-shaft and a free power turbine version of this engine are examined. The major component technology assumptions, in particular the high pressure ratio centrifugal compressor, employed for performance extrapolation are explained and compared with current technology. The potential low NOx emissions of the simple-cycle gas turbine compared to regenerative or recuperative gas turbines is discussed. Finally, some of the problems which might be encountered in using this totally different power plant for the conventional automobile are identified.

Effects of Reynolds number on the performance of a high pressure-ratio turbocharger compressor

2013 ◽  
Vol 56 (6) ◽  
pp. 1361-1369 ◽  
Author(s):  
XinQian Zheng ◽  
Yun Lin ◽  
BinLin Gan ◽  
WeiLin Zhuge ◽  
YangJun Zhang
Keyword(s):  
Reynolds Number ◽  
High Pressure ◽  
Pressure Ratio ◽  
High Pressure Ratio

Effect of Recirculation Device With Counter Swirl Vane on Performance of High Pressure Ratio Centrifugal Compressor

2011 ◽  
Author(s):  
Hideaki Tamaki
Keyword(s):  
High Pressure ◽  
Mach Number ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Negative Slope ◽  
Tip Leakage Flow ◽  
Recirculation Flow ◽  
Operating Range ◽  
High Pressure Ratio

Centrifugal compressors used for turbochargers need to achieve a wide operating range. The author has developed a high pressure ratio centrifugal compressor with pressure ratio 5.7 for a marine use turbocharger. In order to enhance operating range, two different types of recirculation devices were applied. One is a conventional recirculation device. The other is a new one. The conventional recirculation device consists of an upstream slot, bleed slot and the annular cavity which connects both slots. The new recirculation device has vanes installed in the cavity. These vanes were designed to provide recirculation flow with negative preswirl at the impeller inlet, a swirl counterwise to the impeller rotational direction. The benefits of the application of both of the recirculation devices were ensured. The new device in particular, shifted surge line to a lower flow rate compared to the conventional device. This paper discusses how the new recirculation device affects the flow field in the above transonic centrifugal compressor by using steady 3-D calculations. Since the conventional recirculation device injects the flow with positive preswirl at the impeller inlet, the major difference between the conventional and new recirculation device is the direction of preswirl that the recirculation flow brings to the impeller inlet. This study focuses on two effects which preswirl of the recirculation flow will generate. (1) Additional work transfer from impeller to fluid. (2) Increase or decrease of relative Mach number. Negative preswirl increases work transfer from the impeller to fluid as the flow rate reduces. It increases negative slope on pressure ratio characteristics. Hence the recirculation flow with negative preswirl will contribute to stability of the compressor. Negative preswirl also increases the relative Mach number at the impeller inlet. It moves shock downstream compared to the conventional recirculation device. It leads to the suppression of the extension of blockage due to the interaction of shock with tip leakage flow.

scholarly journals Investigation of Flow through a Labyrinth Seal

2021 ◽  
Vol 13 (2) ◽  
pp. 51-58
Author(s):  
Marius ENACHE ◽  
Razvan CARLANESCU ◽  
Andreea MANGRA ◽  
Florin FLOREAN ◽  
Radu KUNCSER
Keyword(s):  
Gas Turbines ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Cfd Modeling ◽  
Gas Temperature ◽  
Continuous Increase ◽  
Seal Design ◽  
Air Temperatures ◽  
Flow Through ◽  
Gas Leaks

Growing performance requirements for gas turbines have led to a continuous increase in gas temperature and pressure ratios. Together with the resulting increase in cooling flows, this requires more and more minimization and control of internal gas leaks. To meet future performance goals, the application of a new seal design and an improved understanding of leakage flow characteristics are of particular importance. The air mass flow through a labyrinth seal designed for a low-pressure turbine has been determined both through analytical calculus and CFD modeling. Different radial clearances and different air temperatures have been considered. In the next stage, the results will be validated through experiments.

scholarly journals The Design and Evaluation of a High Pressure Ratio Radial Turbine

1992 ◽  
Author(s):  
K. R. Pullen ◽  
N. C. Baines ◽  
S. H. Hill
Keyword(s):  
High Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Performance Measurements ◽  
Turbine Engine ◽  
High Pressure Ratio ◽  
Turbine Efficiency ◽  
Wide Range ◽  
Dimensional Parameters ◽  
Very High

A single stage, high speed, high pressure ratio radial inflow turbine was designed for a single shaft gas turbine engine in the 200 kW power range. A model turbine has been tested in a cold rig facility with correct simulation of the important non-dimensional parameters. Performance measurements over a wide range of operation were made, together with extensive volute and exhaust traverses, so that gas velocities and incidence and deviation angles could be deduced. The turbine efficiency was lower than expected at all but the lowest speed. The rotor incidence and exit swirl angles, as obtained from the rig test data, were very similar to the design assumptions. However, evidence was found of a region of separation in the nozzle vane passages, presumably caused by a very high curvature in the endwall just upstream of the vane leading edges. The effects of such a separation are shown to be consistent with the observed performance.

A Novel Hybrid Seal: Design and Experimental Validation on a High Pressure Rotordynamic Test Rig

2021 ◽  
Author(s):  
Giuseppe Vannini ◽  
Benjamin Defoy ◽  
Manjush Ganiger ◽  
Carlo Mazzali
Keyword(s):  
High Pressure ◽  
Pressure Ratio ◽  
Test Rig ◽  
Rotordynamic Coefficients ◽  
Experimental Activity ◽  
Seal Design ◽  
Piston Seal ◽  
Delivery Pressure ◽  
Inlet Swirl ◽  
Primary Focus

Abstract The design and experimental activity presented in this paper is related to a novel hybrid seal which is intended to work as a balance piston seal in an AMBs levitated high-pressure (about 300 bar delivery pressure) motor-compressor. The typical solution adopted for balance piston application is a damper seal (e.g. honeycomb seal), as the rotordynamic stability is a primary focus. However, due to interactions between the AMB controller and seal high stiffness level, the aforementioned selection is not so straightforward. After a review of the state of the art it was found that a combination of some conventional geometries (e.g. labyrinth and honeycomb) can be adopted to achieve the desired target. The design was done using a novel tool combining the validated bulk flow codes for each geometry. Moreover, a CFD analysis, based on some literature references, was carried out as a final verification of the design. The experimental activity was then performed at the Authors’ internal seal test rig. As in typical rotordynamic seal testing activity, the operating parameters leveraged to explore performance sensitivity are rotational speed, inlet pressure, pressure ratio and inlet swirl level. The outcome was satisfactory both in terms of leakage and rotordynamic coefficients.

Stability Improvement of a High-Pressure Ratio Centrifugal Compressor by Flow Injection

2020 ◽  
Vol 33 (6) ◽  
pp. 04020072
Author(s):  
Wenchao Zhang ◽  
Xiao He ◽  
Baotong Wang ◽  
Zhenzhong Sun ◽  
Xinqian Zheng
Keyword(s):  
High Pressure ◽  
Centrifugal Compressor ◽  
Flow Injection ◽  
Pressure Ratio ◽  
High Pressure Ratio
Sign in / Sign up

Export Citation Format

Share Document