System Development and Testing of a Liquid Needle-Free Injector

In order to increase the survivability of the fighter aircraft, the serpentine nozzle has been applied in series of stealth bombers and unmanned aerial vehicles due to its excellent potentiality of evidently suppressing the infrared radiation signatures and radar cross section emitted by engine exhausts. Among the geometric parameters of the serpentine nozzle, the aspect ratio (AR) at the nozzle exit is one of the most critical parameters for the nozzle design as the infrared suppression effect could be greatly enhanced with the increment of AR by strengthening the mixing between the exhaust plume and atmosphere; the aim of this paper is to study the influence of the AR on the flow characteristics of the double serpentine nozzle. The flow features of six double serpentine convergent nozzles, i.e. AR = 3, 5, 7, 9, 11, 15 respectively, were numerically simulated with the shear stress transport κ–ω turbulent model adopted, which had been validated by the experimental data. The characteristics of internal flow and external jet, and the aerodynamic performances of these six nozzles were compared. Results show that the Ma contours at the symmetric plane are different due to the distinct flow accelerations caused by the change of the curvature and the duct height for diverse AR, and the surface pressure and the shock wave features are different correspondingly. The lateral divergence and the lateral convergence characteristics of the nozzle configuration lead to opposite lateral flow under diverse AR, and the change of lateral width induced different lateral pressure gradient, then lead to various lateral vortex distributions. The length of potential core is the contribution of the comprehensive effects of geometry parameters, and it is decreased with the increase of AR due to the dominated effect of the increased mixing area; however, the declining rate is slowed down. The AR of 5 should be chosen for the best aerodynamic performance of the double serpentine nozzle under the qualifications to completely shield the high-temperature turbine.

Download Full-text

A Simple Approach of Groundwater Quality Analysis, Classification, and Mapping in Peshawar, Pakistan

Environments ◽

10.3390/environments6120123 ◽

2019 ◽

Vol 6 (12) ◽

pp. 123

Author(s):

Syed Adnan ◽

Javed Iqbal ◽

Matti Maltamo ◽

Muhammad Suleman Bacha ◽

Asfandyar Shahab ◽

...

Keyword(s):

Groundwater Quality ◽

Groundwater Resources ◽

Regression Tree ◽

Simple Approach ◽

Classification And Regression Tree ◽

Quality Analysis ◽

Quality Data ◽

Critical Parameters ◽

Threshold Values ◽

Cart Analysis

Groundwater is an important source of water for drinking, agriculture, and other household purposes, but high population growth, industrialization, and lack of oversight on environmental policies and implementation have not only degraded the quality but also stressed the quantity of this precious source of water. Many options existed, but this study evaluated, classified, and mapped the quality of groundwater used for potable consumption with a simple approach in an urban area (Peshawar valley) of Pakistan. More than 100 groundwater samples were collected and analyzed for physio-chemical parameters in a laboratory. Hierarchal clustering analysis (HCA) and classification and regression tree (CART) analysis were sequentially applied to produce potential clusters/groups (groundwater quality classes), extract the threshold values of the clusters, classify and map the groundwater quality data into meaningful classes, and identify the most critical parameters in the classification. The HCA produced six distinct potential clusters. We found a high correlation of electrical conductivity with t o t a l h a r d n e s s ( R 2 = 0.72 ), a l k a l i n i t y ( R 2 = 0.59 ) and c h l o r i d e ( R 2 = 0.64 ) , and, t o t a l h a r d n e s s with c h l o r i d e ( R 2 = 0.62), and a l k a l i n i t y ( R 2 = 0.51). The CART analysis conclusively identified the threshold values of the six classes and showed that t o t a l h a r d n e s s was the most critical parameter in the classification. The majority of the groundwater was either with worse quality or good quality, and only a few areas had the worst groundwater quality. This study presents a simple tool for the classification of groundwater quality based on several aesthetic constituents and can assist decision makers develop and support policies and/or regulations to manage groundwater resources.

Download Full-text

Influence of X-Ray Induced Fluorescence on Energy Dispersive X-Ray Analysis of Thin Foils

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100079164 ◽

1977 ◽

Vol 35 ◽

pp. 328-329

Author(s):

E. A. Kenik ◽

J. Bentley

Keyword(s):

Thin Foil ◽

Electron Excitation ◽

Simple Approach ◽

Foil Thickness ◽

X Rays ◽

X Ray ◽

Hole Spectrum ◽

Illumination System ◽

Thin Foils ◽

Intensity Ratios

Cliff and Lorimer (1) have proposed a simple approach to thin foil x-ray analy sis based on the ratio of x-ray peak intensities. However, there are several experimental pitfalls which must be recognized in obtaining the desired x-ray intensities. Undesirable x-ray induced fluorescence of the specimen can result from various mechanisms and leads to x-ray intensities not characteristic of electron excitation and further results in incorrect intensity ratios.In measuring the x-ray intensity ratio for NiAl as a function of foil thickness, Zaluzec and Fraser (2) found the ratio was not constant for thicknesses where absorption could be neglected. They demonstrated that this effect originated from x-ray induced fluorescence by blocking the beam with lead foil. The primary x-rays arise in the illumination system and result in varying intensity ratios and a finite x-ray spectrum even when the specimen is not intercepting the electron beam, an ‘in-hole’ spectrum. We have developed a second technique for detecting x-ray induced fluorescence based on the magnitude of the ‘in-hole’ spectrum with different filament emission currents and condenser apertures.

Download Full-text

Cross-sectional TEM specimen preparation from magneto-optical disk by ultramicrotomy

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100147028 ◽

1993 ◽

Vol 51 ◽

pp. 236-237

Author(s):

F. Shaapur ◽

M.J. Kim ◽

Seh Kwang Lee ◽

Soon Gwang Kim

Keyword(s):

System Development ◽

Thin Foil ◽

Specimen Preparation ◽

Material System ◽

Cross Sectional ◽

Protective Layers ◽

New Material ◽

Diamond Saw ◽

Original Production ◽

Thick Medium

TEM characterization and microanalysis of the recording media is crucial and complementary to new material system development as well as quality control applications. Due to the type of material generally used for supporting the medium, i.e., a polymer, conventional macro- and microthinning procedures for thin foil preparation are not applicable. Ultramicrotorny (UM) is a viable option and has been employed in previous similar studies. In this work UM has been used for preparation of XTEM samples from a magneto-optical (MO) recording medium in its original production format.The as-received material system consisted of a 4-layer, 2100 Å thick medium including a 300 Å TbFeCo layer enveloped by silicon nitride protective layers supported on a 1.2 mm thick × 135 mm (5.25 in.) diameter polycarbonate disk. Recording tracks had an approximate pitch of 1.6 μm separated by 800 Å deep peripheral grooves. Using a Buehler Isomet low-speed diamond saw, 1 mm wide and 20 mm long strips were cut out of the disk along the recording tracks.

Download Full-text