Self-Preserving Mixing Properties of Steady Round Buoyant Turbulent Plumes in Uniform Crossflows

Author(s):  
F. J. Diez ◽  
L. P. Bernal ◽  
G. M. Faeth

The self-preserving mixing properties of steady round buoyant turbulent plumes in uniform crossflows were investigated experimentally. The experiments involved salt water sources injected into fresh water crossflows within the windowed test section of a water channel. Mean and fluctuating concentrations of source fluid were measured over cross sections of the flow using Planar-Laser-Induced-Fluorescence (PLIF) which involved seeding the source fluid with Rhodamine 6G dye and adding small concentrations of ethanol to the crossflowing fluid in order to match the refractive indices of the source flow and the crossflow. The self-preserving penetration properties of the flow were correlated successfully based on the scaling analysis of Diez et al. (2003) whereas the self-preserving structure properties of the flow were correlated successfully based on the scaling analysis of Fischer et al. (1979); both approaches involved assumptions of no-slip convection in the cross stream (horizontal) direction (parallel to the crossflow) and a self-preserving line thermal having a conserved source specific buoyancy flux per unit length that moves in the streamwise (vertical) direction (parallel to the direction of both the initial source flow and the gravity vector). The resulting self-preserving structure consisted of two counter-rotating vortices having their axes nearly aligned with the crossflow direction that move away from the source in the streamwise (vertical) direction due to the action of buoyancy. Present measurements extended up to 202 and 620 source diameters from the source in the streamwise and cross stream directions, respectively. The onset of self-preserving behavior required that the axes of the counter-rotating vortex system be nearly aligned with the crossflow direction. This alignment, in turn, was a strong function of the source/crossflow velocity ratio, uo/v∞. The net result was that the onset of self-preserving behavior was observed at streamwise distances of 10–20 source diameters from the source for uo/v∞ = 4 (the smallest value of uo/v∞ considered), increasing to streamwise distances of 160–170 source diameters from the source for uo/v∞ = 100 (the largest value of uo/v∞ considered). Finally, the counter-rotating vortex system was responsible for substantial increases in the rate of mixing of the source fluid with the ambient fluid compared to axisymmetric round buoyant turbulent plumes in still environments, e.g., transverse dimensions in the presence of the self-preserving counter-rotating vortex system were 2–3 times larger than the transverse dimensions of self-preserving axisymmetric plumes at similar streamwise distances from the source.

2006 ◽  
Vol 128 (10) ◽  
pp. 1001-1011
Author(s):  
F. J. Diez ◽  
L. P. Bernal ◽  
G. M. Faeth

The self-preserving mixing properties of steady round buoyant turbulent plumes in uniform crossflows were investigated experimentally. The experiments involved salt water sources injected into fresh water crossflows within the windowed test section of a water channel. Mean and fluctuating concentrations of source fluid were measured over cross sections of the flow using planar-laser-induced fluorescence which involved seeding the source fluid with Rhodamine 6G dye and adding small concentrations of ethanol to the crossflowing fluid in order to match the refractive indices of the source flow and the crossflow. The self-preserving penetration properties of the flow were correlated successfully based on the scaling analysis of Diez, Bernal, and Faeth (2003, ASME J. Heat Transfer, 125, pp. 1046–1057) whereas the self-preserving structure properties of the flow were correlated successfully based on the scaling analysis of Fischer et al. (1979, Mixing in Inland and Coastal Waters, Academic Press, New York, pp. 315–389); both approaches involved assumptions of no-slip convection in the cross stream (horizontal) direction (parallel to the crossflow) and a self-preserving line thermal having a conserved source specific buoyancy flux per unit length that moves in the streamwise (vertical) direction (parallel to the direction of both the initial source flow and the gravity vector). The resulting self-preserving structure consisted of two counter-rotating vortices having their axes nearly aligned with the crossflow direction that move away from the source in the streamwise (vertical) direction due to the action of buoyancy. Present measurements extended up to 202 and 620 source diameters from the source in the streamwise and cross stream directions, respectively. The onset of self-preserving behavior required that the axes of the counter-rotating vortex system be nearly aligned with the crossflow direction. This alignment, in turn, was a strong function of the source/crossflow velocity ratio, uo∕v∞. The net result was that the onset of self-preserving behavior was observed at streamwise distances of 10–20 source diameters from the source for uo∕v∞=4 (the smallest value of uo∕v∞ considered), increasing to streamwise distances of 160–170 source diameters from the source for uo∕v∞=100 (the largest value of uo∕v∞ considered). Finally, the counter-rotating vortex system was responsible for substantial increases in the rate of mixing of the source fluid with the ambient fluid compared to axisymmetric round buoyant turbulent plumes in still environments, e.g., transverse dimensions in the presence of the self-preserving counter-rotating vortex system were 2–3 times larger than the transverse dimensions of self-preserving axisymmetric plumes at similar streamwise distances from the source.


2005 ◽  
Vol 127 (8) ◽  
pp. 877-887 ◽  
Author(s):  
F. J. Diez ◽  
L. P. Bernal ◽  
G. M. Faeth

The self-preserving mixing properties of steady round nonbuoyant turbulent jets in uniform crossflows were investigated experimentally. The experiments involved steady round nonbuoyant fresh water jet sources injected into uniform and steady fresh water crossflows within the windowed test section of a water channel facility. Mean and fluctuating concentrations of source fluid were measured over cross sections of the flow using planar-laser-induced-fluorescence (PLIF). The self-preserving penetration properties of the flow were correlated successfully similar to Diez et al. [ASME J. Heat Transfer, 125, pp. 1046–1057 (2003)] whereas the self-preserving structure properties of the flow were correlated successfully based on scaling analysis due to Fischer et al. [Academic Press, New York, pp. 315–389 (1979)]; both approaches involve assumptions of no-slip convection in the cross stream direction (parallel to the crossflow) and a self-preserving nonbuoyant line puff having a conserved momentum force per unit length that moves in the streamwise direction (parallel to the initial source flow). The self-preserving flow structure consisted of two counter-rotating vortices, with their axes nearly aligned with the crossflow (horizontal) direction, that move away from the source in the streamwise direction due to the action of source momentum. Present measurements extended up to 260 and 440 source diameters from the source in the streamwise and cross stream directions, respectively, and yielded the following results: jet motion in the cross stream direction satisfied the no-slip convection approximation; geometrical features, such as the penetration of flow boundaries and the trajectories of the axes of the counter-rotating vortices, reached self-preserving behavior at streamwise distances greater than 40–50 source diameters from the source; and parameters associated with the structure of the flow, e.g., contours and profiles of mean and fluctuating concentrations of source fluid, reached self-preserving behavior at streamwise (vertical) distances from the source greater than 80 source diameters from the source. The counter-rotating vortex structure of the self-preserving flow was responsible for substantial increases in the rate of mixing of the source fluid with the ambient fluid compared to corresponding axisymmetric flows in still environments, e.g., transverse dimensions in the presence of the self-preserving counter-rotating vortex structure were 2–3 times larger than transverse dimensions in self-preserving axisymmetric flows at comparable conditions.


Volume 1 ◽  
2004 ◽  
Author(s):  
F. J. Diez ◽  
L. P. Bernal ◽  
G. M. Faeth

The properties of steady round nonbuoyant turbulent jets in uniform crossflows were studied, motivated by applications to the dispersion of heat and potentially harmful substances from steady exhaust flows. Emphasis was placed on self-preserving conditions far from the source where source disturbances have been lost and where jet properties are largely controlled by the conserved properties of the flow. The experiments involved steady round nonbuoyant fresh water jet sources injected into uniform and steady fresh water crossflows within the windowed test section of a water channel facility. Flow visualization was carried out by photographing dye-containing source jets. Mean and fluctuating concentrations of source fluid were measured over cross sections of the flow using Planar Laser-Induced Fluorescence (PLIF). The self-preserving properties of the flow were correlated successfully based on scaling analysis due to Fischer et al. (1979) which involves assumptions of no-slip convection in the cross stream direction (parallel to the crossflow) and a self-preserving nonbuoyant turbulent line puff having a conserved momentum force per unit length that moves in the streamwise direction (parallel to the initial source flow). The flow structure consisted of two counterrotating vortices, with their axes nearly aligned with the crossflow direction, that move away from the source in the streamwise direction due to the action of source momentum. Present measurements extended up to 160 source diameters from the source in the streamwise direction and yielded the following results: jet motion in the cross stream direction satisfied the no-slip convection approximation; geometrical features, such as the penetration of flow boundaries and the trajectories of the axes of the counter-rotating vortices, reached self-preserving behavior at streamwise distances greater than 40–50 source diameters from the source; parameters associated with the structure of the flow, e.g., contours and profiles of mean and fluctuating concentrations of source fluid, however, did not reach self-preserving behavior prior to reaching streamwise (vertical) distances greater than 70–80 source diameters from the source.


2003 ◽  
Vol 125 (5) ◽  
pp. 821-830 ◽  
Author(s):  
F. J. Diez ◽  
R. Sangras ◽  
G. M. Faeth ◽  
O. C. Kwon

The self-preserving properties of round buoyant turbulent starting plumes and starting jets in unstratified environments. The experiments involved dye-containing salt water sources injected vertically downward into still fresh water within a windowed tank. Time-resolved images of the flows were obtained using a CCD camera. Experimental conditions were as follows: source diameters of 3.2 and 6.4 mm, source/ambient density ratios of 1.070 and 1.150, source Reynolds numbers of 4,000–11,000, source Froude numbers of 10–82, volume of source fluid for thermals comprising cylinders having the same cross-sectional areas as the source exit and lengths of 50–382 source diameters, and streamwise flow penetration lengths up to 110 source diameters and 5.05 Morton length scales from the source. Near-source flow properties varied significantly with source properties but the flows generally became turbulent and then became self-preserving within 5 and 20–30 source diameters from the source, respectively. Within the self-preserving region, both normalized streamwise penetration distances and normalized maximum radial penetration distances as functions of time were in agreement with the scaling relationships for the behavior of self-preserving round buoyant turbulent flows to the following powers: time to the 3/4 power for starting plumes and to the 1/2 power for thermals. Finally, the virtual origins of thermals were independent of source fluid volume for the present test conditions.


2016 ◽  
Vol 26 (04) ◽  
pp. 1650065 ◽  
Author(s):  
Mahsa Vaghefi ◽  
Ali Motie Nasrabadi ◽  
Seyed Mohammad Reza Hashemi Golpayegani ◽  
Mohammad Reza Mohammadi ◽  
Shahriar Gharibzadeh

Detrended Fluctuation Analysis (DFA) is a scaling analysis method that can identify intrinsic self-similarity in any nonstationary time series. In contrast, Wavelet Transform (WT) method is widely used to investigate the self-similar processes, as the self-similarity properties exist within the subbands. Therefore, a combination of these two approaches, DFA and WPT, is promising for rigorous investigation of such a system. In this paper a new methodology, so-called wavelet DFA, is introduced and interpreted to evaluate this idea. This approach, further than identifying self-similarity properties, enable us to detect and capture the chaos-periodic transitions, band merging, and internal crisis in systems that become chaotic through period-doubling phenomena. Changes of wavelet DFA exponent have been compared with that of Lyapunov and DFA through Logistic, Sine, Gaussian, Cubic, and Quartic Maps. Furthermore, the potential capabilities of this new exponent have been presented.


Author(s):  
Tomomi Uchiyama

A jet issuing with velocity U0 from a round nozzle of diameter D into the same fluid co-flowing with velocity Ua is simulated by the three-dimensional vortex method. The velocity ratio Ua/U0 is 0.27, while the Reynolds number based on U0 and D is 5.5×104. The number of vortex elements drastically increases in the region where the stretch and contraction of the vortex element occur due to the appearance of turbulence. When applying the core distribution function proposed by Winkelmans and Leonard, the time-averaged velocity successfully satisfies the self-preservation distribution, and the axial component of the turbulent intensity almost agrees with the experimental result. The Reynolds shear stress takes its maximum value at the periphery of the jet in accordance with the experimental result, though it is higher than the experiment.


2016 ◽  
Vol 842 ◽  
pp. 445-450
Author(s):  
Satrio Wicaksono ◽  
Peter Lukito Ferdian ◽  
Tatacipta Dirgantara ◽  
Andi Isra Mahyuddin ◽  
Sandro Mihradi ◽  
...  

Stress distributions that occur in the free end second premolar tooth and its root form dental implant replacement were evaluated using finite element method. In the modelling process, 3D reconstructions were performed. Instead of doing it manually, the 3D reconstruction in this paper was done using cone beam computed tomography (CBCT) scanning process. The 3D reconstruction method used in this paper, is considerably faster than the traditional manual 3D reconstruction method. In order to mimic the actual biting force, static load of 200 N was modelled in the vertical direction parallel to the long axis of the tooth which is placed on bite contact at second premolars and dental implant crown. The stress result on root form dental implant is generally higher than the stress on the natural free end second premolar tooth. The stress concentration locations on root form dental implant were also found and will be used in the future to improve the design of root form dental implant.


2006 ◽  
Author(s):  
Daniel H. Willits ◽  
Meir Teitel ◽  
Josef Tanny ◽  
Mary M. Peet ◽  
Shabtai Cohen ◽  
...  

The objectives of this project were to predict the performance of naturally and fan-ventilated greenhouses as a function of climate, type of crop, evaporative cooling and greenhouse size, and to estimate the effects of the two cooling systems on yield, quality and disease development in the different crops under study. Background In the competitive field of greenhouse cultivation, growers and designers in both the US and Israel are repeatedly forced to choose between naturally ventilated (NV) and fan ventilated (FV) cooling systems as they expand their ranges in an effort to remain profitable. The known advantages and disadvantages of each system do not presently allow a clear decision. Whether essentially zero operating costs can offset the less dependable cooling of natural ventilation systems is question this report hopes to answer. Major Conclusions US It was concluded very early on that FV greenhouses without evaporative pad cooling are not competitive with NV greenhouses during hot weather. During the first year, the US team found that average air temperatures were always higher in the FV houses, compared to the NV houses, when evaporative pad cooling was not used, regardless of ventilation rate in the FV houses or the vent configuration in the NV houses. Canopy temperatures were also higher in the FV ventilated houses when three vents were used in the NV houses. A second major conclusion was that the US team found that low pressure fogging (4 atm) in NV houses does not completely offset the advantage of evaporative pad cooling in FV houses. High pressure fog (65 atm) is more effective, but considerably more expensive. Israel Experiments were done with roses in the years 2003-2005 and with tomatoes in 2005. Three modes of natural ventilation (roof, side and side + roof openings) were compared with a fan-ventilated (with evaporative cooling) house. It was shown that under common practice of fan ventilation, during summer, the ventilation rate is usually lower with NV than with FV. The microclimate under both NV and FV was not homogeneous. In both treatments there were strong gradients in temperature and humidity in the vertical direction. In addition, there were gradients that developed in horizontal planes in a direction parallel to the direction of the prevailing air velocity within the greenhouse. The gradients in the horizontal direction appear to be larger with FV than with NV. The ratio between sensible and latent heat fluxes (Bowen ratio) was found to be dependent considerably on whether NV or FV is applied. This ratio was generally negative in the naturally ventilated house (about -0.14) and positive in the fan ventilated one (about 0.19). Theoretical models based on Penman-Monteith equation were used to predict the interior air and crop temperatures and the transpiration rate with NV. Good agreement between the model and experimental results was obtained with regard to the air temperature and transpiration with side and side + roof ventilation. However, the agreement was poor with only roof ventilation. The yield (number of rose stems longer than 40 cm) was higher with FV


Sign in / Sign up

Export Citation Format

Share Document