Energy and Exergy Analysis of Gas Turbine – Fuel Cell Based Combined Cycle Power Plant

2011 ◽  
Author(s):  
M. Sreeramulu ◽  
A. V. S. S. K. S. Gupta ◽  
T. Srinivas
Keyword(s):  
Power Generation ◽  
Fuel Cell ◽  
Gas Turbine ◽  
Compression Ratio ◽  
Gas Turbines ◽  
System Modeling ◽  
Combined Cycle ◽  
Energy Utilization ◽  
Inlet Temperature ◽  
Exergy Destruction

The newer power generation systems are becoming more important for the society due to increase in demand for the electrical energy utilization and higher energy conversion efficiencies. Though it is not new, fuel cell technology is one of the promising systems for cleaner and competitive alternate power generation system. When the fuel cells are integrated with the gas turbines, the total thermal efficiency of the combined cycle can be obtained greater than 60%. This is appreciably better exergetic performance when compared to traditional gas turbine cycle. In this work, thermodynamic analysis of SOFC-GT combined system (2.898MW) has been carried out, to evaluate energy efficiency, exergy efficiency and exergy destruction of each component is calculated. The effect of compression ratio (rp), turbine inlet temperature (TIT), air fuel ratio and ambient temperature of air, on the performance of the system has been analyzed by adopting the different fuels. The outcome of the system modeling reveals that SOFC and combustion chamber are the main sources of exergy destruction. When the methane, natural gas and coal gas are used as fuels, at the optimum compression ratio 9, the total thermal efficiencies are found to be 63.3%, 62.12% and 61.02% respectively. The exergy efficiencies are obtained respectively as 60.85%, 59.16% and 60.06%.

A Study on Low NOx Combustion in LBG-Fueled 1500°C-Class Gas Turbine

1994 ◽  
Author(s):  
Toshihiko Nakata ◽  
Mikio Sato ◽  
Toru Ninomiya ◽  
Takeharu Hasegawa
Keyword(s):  
Power Generation ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combustion Process ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Gas Temperature ◽  
Secondary Air

Developing integrated coal gasification combined cycle systems ensures cost-effective and environmentally sound options for supplying future power generation needs. The reduction of NOx emissions and increasing the inlet temperature of gas turbines are the most significant issues in gas turbine development in an Integrated Coal Gasification Combined Cycle (IGCC) power generation systems. The coal gasified fuel, which is produced in a coal gasifier of air-blown entrained-flow type has calorific value as low as 1/10 of natural gas. Furthermore the fuel gas contains ammonia when a gas cleaning system is a hot type, and ammonia will be converted to nitrogen oxides in the combustion process of a gas turbine. This study is performed in a 1500°C-class gas turbine combustor firing low-Btu coal-gasified fuel in IGCC systems. An advanced rich-lean combustor of 150-MW class gas turbine was designed to hold stable combustion burning low-Btu gas and to reduce fuel NOx emission that is produced from the ammonia in the fuel. The main fuel and the combustion air is supplied into fuel-rich combustion chamber with strong swirl flow and make fuel-rich flame to decompose ammonia into intermediate reactants such as NHi and HCN. The secondary air is mixed with primary combustion gas dilatorily to suppress the oxidization of ammonia reactants in fuel-lean combustion chamber and to promote a reducing process to nitrogen. By testing it under atmospheric pressure conditions, the authors have obtained a very significant result through investigating the effect of combustor exit gas temperature on combustion characteristics. Since we have ascertained the excellent performance of the tested combustor through our extensive investigation, we wish to report on the results.

A Study on Low NOx Combustion in LBG-Fueled 1500°C-Class Gas Turbine

1996 ◽  
Vol 118 (3) ◽  
pp. 534-540 ◽  
Author(s):  
T. Nakata ◽  
M. Sato ◽  
T. Ninomiya ◽  
T. Hasegawa
Keyword(s):  
Power Generation ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combustion Process ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Nox Emissions ◽  
Gas Temperature

Developing integrated coal gasification combined-cycle systems ensures cost-effective and environmentally sound options for supplying future power generation needs. The reduction of NOx emissions and increasing the inlet temperature of gas turbines are the most significant issues in gas turbine development in Integrated Coal Gasification Combined Cycle (IGCC) power generation systems. The coal gasified fuel, which is produced in a coal gasifier of an air-blown entrained-flow type has a calorific value as low as 1/10 of natural gas. Furthermore, the fuel gas contains ammonia when a gas cleaning system is a hot type, and ammonia will be converted to nitrogen oxides in the combustion process of a gas turbine. This study is performed in a 1500°C-class gas turbine combustor firing low-Btu coal-gasified fuel in IGCC systems. An advanced rich-lean combustor of 150-MW class gas turbine was designed to hold stable combustion burning low-Btu gas and to reduce fuel NOx emissions from the ammonia in the fuel. The main fuel and the combustion air are supplied into a fuel-rich combustion chamber with strong swirl flow and make fuel-rich flame to decompose ammonia into intermediate reactants such as NHi and HCN. The secondary air is mixed with primary combustion gas dilatorily to suppress the oxidization of ammonia reactants in fuel-lean combustion chamber and to promote a reducing process to nitrogen. By testing under atmospheric pressure conditions, the authors have obtained a very significant result through investigating the effect of combustor exit gas temperature on combustion characteristics. Since we have ascertained the excellent performance of the tested combustor through our extensive investigation, we wish to report on the results.

Effect of Pressure on Combustion Characteristics in LBG-Fueled 1300°C-Class Gas Turbine

1994 ◽  
Vol 116 (3) ◽  
pp. 554-558 ◽  
Author(s):  
T. Nakata ◽  
M. Sato ◽  
T. Ninomiya ◽  
T. Yoshine ◽  
M. Yamada
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combustion Process ◽  
Combined Cycle ◽  
Combustion Characteristics ◽  
Inlet Temperature ◽  
Effect Of Pressure ◽  
Coal Gasifier

Developing integrated coal gasification combined cycle systems ensures that Japan will have cost-effective and environmentally sound options for supplying future power generation needs. Reduction of NOx emissions and increasing the inlet temperature of gas turbines are the most significant issues in gas turbine development in IGCC. The coal gasified fuel, which is produced in a coal gasifier of air blown entrained-flow type has a calorific value as low as 1/10 of natural gas. Furthermore, the fuel gas contains ammonia when a gas cleaning system is a hot type, and ammonia will be converted to nitrogen oxides in the combustion process of a gas turbine. The study is performed in 1300°C-class gas turbine combustor firing coal-gasifier fuel in IGCC power generation systems. In the previous study [1] the advanced rich-lean combustor of 150-MW class gas turbine was designed to hold stable combustion burning low-Btu gas fuel and to reduce fuel NOx emission that is produced from the ammonia in the fuel. By testing it under atmospheric pressure conditions, we have studied the effects of fuel parameters on combustor performances and listed the basic data for development applications. In this study, by testing it under pressurized conditions, we have obtained a very significant result through investigating the effect of pressure on combustion characteristics and wish to provide herein a summary of our findings.

scholarly journals Effect of Pressure on Combustion Characteristics in LBG–Fueled 1300°C–Class Gas Turbine

1993 ◽  
Author(s):  
Toshihiko Nakata ◽  
Mikio Sato ◽  
Toru Ninomiya ◽  
Toshiyuki Yoshine ◽  
Masahiko Yamada
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combustion Process ◽  
Combined Cycle ◽  
Combustion Characteristics ◽  
Inlet Temperature ◽  
Gas Cleaning ◽  
Effect Of Pressure

Developing integrated coal gasification combined cycle systems ensures that Japan will have cost–effective and environmentally sound options for supplying future power generation needs. The reduction of NOx emissions and increasing the inlet temperature of gas turbines are the most significant issues in gas turbine development in IGCC. The coal gasified fuel, which is produced in a coal gasifier of air–blown entrained–flow type has calorific value as low as 1/10 of natural gas. Furthermore the fuel gas contains ammonia when a gas cleaning system is a hot type, and ammonia will be converted to nitrogen oxides in the combustion process of a gas turbine. The study is performed in 1300°C–class gas turbine combustor firing coal–gasified fuel in IGCC power generation systems. In the previous study the advanced rich–lean combustor of 150–MW class gas turbine was designed to hold stable combustion burning low–Btu gas fuel and to reduce fuel NOx emission that is produced from the ammonia in the fuel. By testing it under atmospheric pressure conditions, we have studied the effects of fuel parameters on combustor performances and listed the basic data for development applications. In this study, by testing it under pressurized conditions, we have obtained a very significant result through investigating the effect of pressure on combustion characteristics and wish to provide herein a summary of our findings.

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

scholarly journals Development of a Low-NOx LBG Combustor for Coal Gasification Combined Cycle Power Generation Systems

1989 ◽  
Author(s):  
M. Sato ◽  
T. Abe ◽  
T. Ninomiya ◽  
T. Nakata ◽  
T. Yoshine ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Coal Gasification ◽  
Combined Cycle ◽  
Generation System ◽  
Combustion Technology ◽  
Power Generation System ◽  
Combustion Tests ◽  
Power Generation Systems

From the view point of future coal utilization technology for the thermal power generation systems, the coal gasification combined cycle system has drawn special interest recently. In the coal gasification combined cycle power generation system, it is necessary to develop a high temperature gas turbine combustor using a low-BTU gas (LBG) which has high thermal efficiency and low emissions. In Japan a development program of the coal gasification combined cycle power generation system has started in 1985 by the national government and Japanese electric companies. In this program, 1300°C class gas turbines will be developed. If the fuel gas cleaning system is a hot type, the coal gaseous fuel to be supplied to gas turbines will contain ammonia. Ammonia will be converted to nitric oxides in the combustion process in gas turbines. Therefore, low fuel-NOx combustion technology will be one of the most important research subjects. This paper describes low fuel-NOx combustion technology for 1300°C class gas turbine combustors using coal gaseous low-BTU fuel as well as combustion characteristics and carbon monoxide emission characteristics. Combustion tests were conducted using a full-scale combustor used for the 150 MW gas turbine at the atmospheric pressure. Furthermore, high pressure combustion tests were conducted using a half-scale combustor used for the 1 50 MW gas turbine.

Application of Ultra-Low NOx Combustor to the MHPS Existing Gas Turbine

2021 ◽  
Author(s):  
Takashi Nishiumi ◽  
Hirofumi Ohara ◽  
Kotaro Miyauchi ◽  
Sosuke Nakamura ◽  
Toshishige Ai ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Operational Experience ◽  
Emission Rates ◽  
Gas Temperature ◽  
Design Development ◽  
And Control

Abstract In recent years, MHPS achieved a NET M501J gas turbine combined cycle (GTCC) efficiency in excess of 62% operating at 1,600°C, while maintaining NOx under 25ppm. Taking advantage of our gas turbine combustion design, development and operational experience, retrofits of earlier generation gas turbines have been successfully applied and will be described in this paper. One example of the latest J-Series technologies, a conventional pilot nozzle was changed to a premix type pilot nozzle for low emission. The technology was retrofitted to the existing F-Series gas turbines, which resulted in emission rates of lower than 9ppm NOx(15%O2) while maintaining the same Turbine Inlet Temperature (TIT: Average Gas Temperature at the exit of the transition piece). After performing retrofitting design, high pressure rig tests, the field test prior to commercial operation was conducted on January 2019. This paper describes the Ultra-Low NOx combustor design features, retrofit design, high pressure rig test and verification test results of the upgraded M501F gas turbine. In addition, it describes another upgrade of turbine to improve efficiency and of combustion control system to achieve low emissions. Furthermore it describes the trouble-free upgrade of seven (7) units, which was completed by utilizing MHPS integration capabilities, including handling all the design, construction and service work of the main equipment, plant and control systems.

Operation Experiences of Siemens IGCC Gas Turbines Using Gasification Products From Coal and Refinery Residues

2000 ◽  
Author(s):  
M. Huth ◽  
A. Heilos ◽  
G. Gaio ◽  
J. Karg
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Strong Impact ◽  
Coal Gas ◽  
Operation Conditions ◽  
Wide Range ◽  
Commercial Operation ◽  
Burner Design

The Integrated Gasification Combined Cycle concept is an emerging technology that enables an efficient and clean use of coal as well as residuals in power generation. After several years of development and demonstration operation, now the technology has reached the status for commercial operation. SIEMENS is engaged in 3 IGCC plants in Europe which are currently in operation. Each of these plants has specific characteristics leading to a wide range of experiences in development and operation of IGCC gas turbines fired with low to medium LHV syngases. The worlds first IGCC plant of commercial size at Buggenum/Netherlands (Demkolec) has already demonstrated that IGCC is a very efficient power generation technology for a great variety of coals and with a great potential for future commercial market penetration. The end of the demonstration period of the Buggenum IGCC plant and the start of its commercial operation has been dated on January 1, 1998. After optimisations during the demonstration period the gas turbine is running with good performance and high availability and has exceeded 18000 hours of operation on coal gas. The air-side fully integrated Buggenum plant, equipped with a Siemens V94.2 gas turbine, has been the first field test for the Siemens syngas combustion concept, which enables operation with very low NOx emission levels between 120–600 g/MWh NOx corresponding to 6–30 ppm(v) (15%O2) and less than 5 ppm(v) CO at baseload. During early commissioning the syngas nozzle has been recognised as the most important part with strong impact on combustion behaviour. Consequently the burner design has been adjusted to enable quick and easy changes of the important syngas nozzle. This design feature enables fast and efficient optimisations of the combustion performance and the possibility for easy adjustments to different syngases with a large variation in composition and LHV. During several test runs the gas turbine proved the required degree of flexibility and the capability to handle transient operation conditions during emergency cases. The fully air-side integrated IGCC plant at Puertollano/Spain (Elcogas), using the advanced Siemens V94.3 gas turbine (enhanced efficiency), is now running successfully on coal gas. The coal gas composition at this plant is similar to the Buggenum example. The emission performance is comparable to Buggenum with its very low emission levels. Currently the gas turbine is running for the requirements of final optimization runs of the gasifier unit. The third IGCC plant (ISAB) equipped with Siemens gas turbine technology is located at Priolo near Siracusa at Sicilly/Italy. Two Siemens V94.2K (modified compressor) gas turbines are part of this “air side non-integrated” IGCC plant. The feedstock of the gasification process is a refinery residue (asphalt). The LHV is almost twice compared to the Buggenum or Puertollano case. For operation with this gas, the coal gas burner design was adjusted and extensively tested. IGCC operation without air extraction has been made possible by modifying the compressor, giving enhanced surge margins. Commissioning on syngas for the first of the two gas turbines started in mid of August 1999 and was almost finished at the end of August 1999. The second machine followed at the end of October 1999. Since this both machines are released for operation on syngas up to baseload.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Sign in / Sign up

Export Citation Format

Share Document