Effects of Inlet Fogging and Wet Compression on Gas Turbine Performance

2006 ◽  
Author(s):  
Sepehr Sanaye ◽  
Hossein Rezazadeh ◽  
Mehrdad Aghazeynali ◽  
Mehrdad Samadi ◽  
Daryoush Mehranian ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Water Droplets ◽  
Turbine Performance ◽  
Compressor Inlet ◽  
Wet Compression ◽  
Inlet Duct

Inlet fogging has been noticed widely in recent years as a method of gas turbine air inlet cooling for increasing the power output of gas turbines and combined cycle power plants. To study the effects of inlet fogging on gas turbine performance, in the first step, the evaporation of water droplets in the compressor inlet duct was modeled, and at the end of the inlet duct, the diameter of water droplets were estimated. The results of this process were compared with the results of FLUENT software. In the second step, the droplets which were not evaporated in compressor inlet duct were studied during wet compression in the compressor and the reduction in compressor discharge air temperature was predicted. Finally, the effects of both evaporative cooling in inlet duct, and wet compression in compressor, on the power output, and turbine exhaust temperature of a gas turbine with turbine blade cooling were investigated. These results for various amounts of air bleeding, without and with inlet fogging in the range of (0–2%) overspray are reported.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

Second Law Efficiency of the Rankine Bottoming Cycle of a Combined Cycle Power Plant

2008 ◽  
Author(s):  
S. Can Gulen ◽  
Raub W. Smith
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Second Law ◽  
Modeling Tools ◽  
Combined Cycle Power Plant

A significant portion of the new electrical generating capacity installed in the past decade has employed heavy-duty gas turbines operating in a combined cycle configuration with a steam turbine bottoming cycle. In these power plants approximately one third of the power is generated by the bottoming cycle. To ensure that the highest possible combined cycle efficiency is realized it is important to develop the combined cycle power plant as a system. Doing so requires a solid understanding of the efficiency entitlement of both, topping and bottoming, cycles separately and as a whole. This paper describes a simple but accurate method to estimate the Rankine bottoming cycle power output directly from the gas turbine exhaust exergy utilizing the second law of thermodynamics. The classical first law approach, i.e. the heat and mass balance method, requires lengthy calculations and complex computer-based modeling tools to evaluate Rankine bottoming cycle performance. In this paper, a rigorous application of the fundamental thermodynamic principles embodied by the second law to the major cycle components clearly demonstrates that the Rankine cycle performance can be accurately represented by several key parameters. The power of the second law approach lies in its ability to highlight the theoretical entitlement and state-of-the-art design performances simultaneously via simple, fundamental relationships. By considering economically and technologically feasible upper limits for the key parameters, the maximum achievable bottoming cycle power output is readily calculable for any given gas turbine from its exhaust exergy.

Second Law Efficiency of the Rankine Bottoming Cycle of a Combined Cycle Power Plant

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
S. Can Gülen ◽  
Raub W. Smith
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Combined Cycle ◽  
Cycle Performance ◽  
Second Law ◽  
Modeling Tools ◽  
Combined Cycle Power Plant

A significant portion of the new electrical generating capacity installed in the past decade has employed heavy-duty gas turbines operating in a combined cycle configuration with a steam turbine bottoming cycle. In these power plants approximately one-third of the power is generated by the bottoming cycle. To ensure that the highest possible combined cycle efficiency is realized it is important to develop the combined cycle power plant as a system. Doing so requires a solid understanding of the efficiency entitlement of both, topping and bottoming, cycles separately and as a whole. This paper describes a simple but accurate method to estimate the Rankine bottoming cycle power output directly from the gas turbine exhaust exergy, utilizing the second law of thermodynamics. The classical first law approach, i.e., the heat and mass balance method, requires lengthy calculations and complex computer-based modeling tools to evaluate Rankine bottoming cycle performance. In this paper, a rigorous application of the fundamental thermodynamic principles embodied by the second law to the major cycle components clearly demonstrates that the Rankine cycle performance can be accurately represented by several key parameters. The power of the second law approach lies in its ability to highlight the theoretical entitlement and state-of-the-art design performances simultaneously via simple fundamental relationships. By considering economically and technologically feasible upper limits for the key parameters, the maximum achievable bottoming cycle power output is readily calculable for any given gas turbine from its exhaust exergy.

Inlet Air Cooling Methods for Gas Turbine Based Power Plants

2004 ◽  
Author(s):  
E. Kakaras ◽  
A. Doukelis ◽  
A. Prelipceanu ◽  
S. Karellas
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Evaporative Cooling ◽  
Climatic Conditions ◽  
Combined Cycle ◽  
Air Cooling ◽  
Cooling Systems ◽  
Cooling Methods

Power generation from gas turbines is penalised by a substantial power output loss with increased ambient temperature. By cooling down the gas turbine intake air, the power output penalty can be mitigated. The purpose of this paper is to review the state of the art in applications for reducing the gas turbine intake air temperature and examine the merits from integration of the different air-cooling methods in gas turbine based power plants. Three different intake air-cooling methods (evaporative cooling, refrigeration cooling and evaporative cooling of pre-compressed air) have been applied in two combined cycle power plants and two gas turbine plants. The calculations were performed on a yearly basis of operation, taking into account the time-varying climatic conditions. The economics from integration of the different cooling systems were calculated and compared.

Combined Cycle Power Augmentation by Inlet Fogging

2005 ◽  
Author(s):  
Hsiao-Wei D. Chiang ◽  
Pai-Yi Wang
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Peak Load ◽  
Combined Cycle ◽  
Augmentation Strategies ◽  
Combined Cycles ◽  
Increasing Demand ◽  
Plant Simulation

Inlet fogging of gas turbine engines has attained considerable popularity due to the ease of installation and the relatively low first cost compared to other inlet cooling methods. With increasing demand for power and with shortages envisioned especially during the peak load times during the summers, there is a need to boost gas turbine power. In Taiwan, most gas turbines operate with combined cycle for base load. Only a small portion operates with simple-cycle for peak load. To recover lost power output due to increased ambient temperature in hot days, the power augmentation strategies for combined-cycles need to be studied in advance. Therefore, the objective is to study the effects caused by adding inlet fogging to an existing gas turbine-based combined-cycle power plant. Simulation runs were made for adding inlet fogging to a combined cycle with two Alstom gas turbines, two heatrecovery steam generators, and one steam turbine. Results show that the power output will be increased by 1% to 5% in typical hot summer days. Since there are seventeen combined-cycle power plants located in different areas in Taiwan, total extra power output gained by inlet fogging can make up the power loss in hot summer days. This paper also includes a parametric study of performance to provide guidelines for combined-cycle power augmentation by inlet fogging.

Theoretical and Experimental Study of Compressor and Gas Turbine Performances With Wet Compression

2002 ◽  
Author(s):  
Yunhui Wang ◽  
Qun Zheng ◽  
Yufeng Sun ◽  
Guoxue Wang
Keyword(s):  
Experimental Study ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
High Ambient Temperature ◽  
Turbine Performance ◽  
Wet Compression ◽  
Industrial Gas Turbine ◽  
Engine Power

Theoretical and experimental study of compressor and gas turbine performance with wet compression has been carried out on S1A-02 industrial gas turbine to reveal its effects on gas turbines, compressors. Experiment results show that wet compression has significantly effects on performances of gas turbines and compressors; under situations of high ambient temperature, wet compression can be used to restore engine power output.

Parametric Study of Inlet Cooling With Varied COP on Gas Turbine Performance

2014 ◽  
Author(s):  
Maryam Besharati-Givi ◽  
Xianchang Li
Keyword(s):  
Ambient Temperature ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
High Efficiency ◽  
Cooling System ◽  
Coefficient Of Performance ◽  
Inlet Temperature ◽  
Turbine Performance ◽  
Compressor Inlet

Gas turbines play an important role in power generation, and it is therefore desired to operate gas turbines with high efficiency and power output. One of the most influential parameters on the performance of a gas turbine is the ambient condition. It is known that inlet cooling can improve the gas turbine performance, especially when the ambient temperature is high. This study examines the effect of inlet cooling with different operating parameters such as compressor inlet temperature, turbine inlet temperature, air fuel ratio, and pressure ratio. Furthermore, the coefficient of performance (COP) of the cooling system is considered a function of the ambient temperature. Aspen Plus software is used to simulate the system under a steady-flow condition. The results indicate that the cooling of the compressor inlet air can substantially improve the power output as well as the overall efficiency of system. More importantly, there exists an optimal temperature at which the inlet cooling should be operated to achieve the highest efficiency.

Simulation of Producer Gas Fired Power Plants With Inlet Fog Cooling and Steam Injection

2006 ◽  
Author(s):  
Mun Roy Yap ◽  
Ting Wang
Keyword(s):  
Natural Gas ◽  
Steam Turbine ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Power Plants ◽  
Steam Injection ◽  
Combined Cycle ◽  
Producer Gas ◽  
Cycle Systems

Biomass can be converted to energy via direct combustion or thermo-chemical conversion to liquid or gas fuels. This study focuses on burning producer gases derived from gasifying biomass wastes to produce power. Since the producer gases are usually low calorific values (LCV), the power plants performance under various operating conditions has not yet been proven. In this study, system performance calculations are conducted for 5MWe power plants. The power plants considered include simple gas turbine systems, steam turbine systems, combined cycle systems, and steam injection gas turbine systems (STIG) using the producer gas with low calorific values at approximately 30% and 15% of the natural gas heating value (on a mass basis). The LCV fuels are shown to impose high back compressor pressure and produces increased power output due to increased fuel flow. Turbine nozzle throat area is adjusted to accommodate additional fuel flows to allow compressor operate within safety margin. The best performance occurs when the designed pressure ratio is maintained by widening nozzle openings, even though the TIT is reduced under this adjustment. Power augmentations under four different ambient conditions are calculated by employing gas turbine inlet fog cooling. Comparison between inlet fog cooling and steam injection using the same amount of water mass flow indicates that steam injection is less effective than inlet fog cooling in augmenting power output. Maximizing steam injection, at the expense of supplying the steam to the steam turbine, significantly reduces both the efficiency and the output power of the combined cycle. This study indicates that the performance of gas turbine and combined cycle systems fueled by the LCV fuels could be very different from the familiar behavior of natural gas fired systems. Care must be taken if on-shelf gas turbines are modified to burn LCV fuels.

HRSG Duct Firing Revisited

2018 ◽  
Author(s):  
S. Can Gülen
Keyword(s):  
Power Plant ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Fossil Fuel ◽  
Heat Rate ◽  
Combined Cycle ◽  
Efficiency Improvement ◽  
Combined Cycle Power Plant

Duct firing in the heat recovery steam generator (HRSG) of a gas turbine combined cycle power plant is a commonly used method to increase output on hot summer days when gas turbine airflow and power output lapse significantly. The aim is to generate maximum possible power output when it is most needed (and, thus, more profitable) at the expense of power plant heat rate. In this paper, using fundamental thermodynamic arguments and detailed heat and mass balance simulations, it will be shown that, under certain boundary conditions, duct firing in the HRSG can be a facilitator of efficiency improvement as well. When combined with highly-efficient aeroderivative gas turbines with high cycle pressure ratios and concomitantly low exhaust temperatures, duct firing can be utilized for small but efficient combined cycle power plant designs as well as more efficient hot-day power augmentation. This opens the door to efficient and agile fossil fuel-fired power generation opportunities to support variable renewable generation.

scholarly journals Advanced Aeroderivative Gas Turbines in Coal-Based High Performance Power Systems (HIPPS)

1998 ◽  
Author(s):  
F. L. Robson ◽  
D. J. Seery
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Power Plants ◽  
Performance Standards ◽  
Combined Cycle ◽  
Advanced Technology ◽  
Early 21St Century ◽  
Near Term

The Department of Energy’s Federal Energy Technology Center (FETC) is sponsoring the Combustion 2000 Program aimed at introducing clean and more efficient advanced technology coal-based power systems in the early 21st century. As part of this program, the United Technologies Research Center has assembled a seven member team to identify and develop the technology for a High Performance Power Systems (HIPPS) that will provide in the near term, 47% efficiency (HHV), and meet emission goals only one-tenth of current New Source Performance Standards for coal-fired power plants. In addition, the team is identifying advanced technologies that could result in HIPPS with efficiencies approaching 55% (HHV). The HIPPS is a combined cycle that uses a coal-fired High Temperature Advanced Furnace (HITAF) to preheat compressor discharge air in both convective and radiant heaters. The heated air is then sent to the gas turbine where additional fuel, either natural gas or distillate, is burned to raise the temperature to the levels of modern gas turbines. Steam is raised in the HITAF and in a Heat Recovery Steam Generator for the steam bottoming cycle. With state-of-the-art frame type gas turbines, the efficiency goal of 47% is met in a system with more than two-thirds of the heat input furnished by coal. By using advanced aeroderivative engine technology, HIPPS in combined-cycle and Humid Air Turbine (HAT) cycle configurations could result in efficiencies of over 50% and could approach 55%. The following paper contains descriptions of the HIPPS concept including the HITAF and heat exchangers, and of the various gas turbine configurations. Projections of HIPPS performance, emissions including significant reduction in greenhouse gases are given. Application of HIPPS to repowering is discussed.

Sign in / Sign up

Export Citation Format

Share Document