Spray Generated by an Airblast Atomizer at High-Pressure Conditions

2007 ◽  
Author(s):  
Feras Z. Batarseh ◽  
Ilia V. Roisman ◽  
Cam Tropea
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Velocity Vector ◽  
Ambient Pressure ◽  
Air Flow ◽  
Water Flow Rate ◽  
The Other ◽  
Air Flow Rate ◽  
Spray Visualization

We present an experimental investigation of a spray generated by an airblast atomizer. Experiments have been performed in a pressure chamber equipped by transparent windows allowing an optical access to the spray. Several techniques of spray investigation have been applied: spray visualization using the high-speed video system, spray visualization and instantaneous velocity measurements using the PIV technique, spray velocimetry and sizing using the IPI and phase Doppler instruments. Phase Doppler instrument has been used to characterize the droplets in the spray: their diameter, two components of the velocity vector. Also the integral parameters of the spray, such as the local volume flux density, have been characterized. We conduct a parametric study of the effect of the ambient pressure, the air flow rate and the water flow rate on an atomized spray. Measurements at different radial locations in the spray and in two planes were performed. The measurements in these two planes allow one to determine the distributions of all the three components of the average drop velocity vector: axial, radial and azimuthal. PDA measurements show that atomized spray is sensitive to any change in the studied parameters. For example, increasing air flow rate from 20 SCMH to 45 SCMH and keeping same water flow rate and pressure, leads to an increase in all velocity components and also to a change in droplets diameters. On the other hand, keeping constant pressure and air flow rate and increasing water flow rate from 0.7 to 1.4 l/hr, leads to an increase in water droplets sizes and the axial velocity component, whereas the other velocity components show a non uniform change. Moreover, increasing the ambient pressure leads to the growth of the spray velocity and drops diameters.

scholarly journals Experimental Investigation on Improvement of Wet Cooling Tower Efficiency with Diverse Packing Compaction Using ANN-PSO Algorithm

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 167
Author(s):  
Hasan Alimoradi ◽  
Madjid Soltani ◽  
Pooriya Shahali ◽  
Farshad Moradi Kashkooli ◽  
Razieh Larizadeh ◽  
...  
Keyword(s):  
Neural Network ◽  
Water Temperature ◽  
Water Flow ◽  
Flow Rate ◽  
Cooling Tower ◽  
Air Flow ◽  
Water Flow Rate ◽  
Pso Algorithm ◽  
Outlet Temperature ◽  
Air Flow Rate

In this study, a numerical and empirical scheme for increasing cooling tower performance is developed by combining the particle swarm optimization (PSO) algorithm with a neural network and considering the packing’s compaction as an effective factor for higher accuracies. An experimental setup is used to analyze the effects of packing compaction on the performance. The neural network is optimized by the PSO algorithm in order to predict the precise temperature difference, efficiency, and outlet temperature, which are functions of air flow rate, water flow rate, inlet water temperature, inlet air temperature, inlet air relative humidity, and packing compaction. The effects of water flow rate, air flow rate, inlet water temperature, and packing compaction on the performance are examined. A new empirical model for the cooling tower performance and efficiency is also developed. Finally, the optimized performance conditions of the cooling tower are obtained by the presented correlations. The results reveal that cooling tower efficiency is increased by increasing the air flow rate, water flow rate, and packing compaction.

Water Flow Distribution in Horizontal Protruding-Type Header Contaminated With Bubbles

1999 ◽  
Author(s):  
Sachiyo Horiki ◽  
Masahiro Osakabe
Keyword(s):  
Uniform Distribution ◽  
Gas Phase ◽  
Water Flow ◽  
Flow Rate ◽  
Water Distribution ◽  
Air Flow ◽  
Water Flow Rate ◽  
Flow Distribution ◽  
Air Flow Rate ◽  
Distribution Behavior

Abstract Flow header for small multiple pipes is commonly used in boilers and heat exchangers. The system contributes to raise the heat transfer efficiency in the components. The flow distribution mechanism of the header for water has been studied and the calculation procedure for the design has been recommended for a single-phase condition. It is also recommended to avoid the bubbles in the header to obtain a uniform water flow rate to each small pipe. But in some cases, the header has to be used to distribute a flow containing bubbles. Distribution behavior of water with a gas-phase was studied experimentally in a horizontal header with four vertical pipes. In the present experimental header, it was possible to protrude the branch pipes inside of the header and the effect of protruding length on the water distribution behavior was studied. When the protruding length was 0, the water distribution rate to the first pipe rapidly increased and the rates to the others decreased with a small amount of bubbles. As the bubbles in the header were absorbed only into the first pipe, the average two-phase density in the first pipe decreased. The decreased pressure head promotes the rush of water into the first pipe such as in an airlift pump. By increasing the air flow rate in the header inlet further, the flow rate to the first pipe took a maximum and then tended to decrease. The increased air flow rate in the first pipe increased the pressure loss in the pipe and resulted in a reduction in the water flow rate. The more important and serious behavior could be seen in the other pipes where the water flow rate decreased to 1/5 of the uniform distribution rate. By increasing the protruding length, the non-uniform distribution of water was suppressed because the gas-phase entered not only the first pipe but also the others. The best result was obtained when the four branch pipes were protruded into the center of header.

Development of Air/Water Two-Phase Flow Centrifugal Pump and Its Operating Characteristics

2003 ◽  
Author(s):  
Akinori Furukawa ◽  
Satoshi Ohshita ◽  
Kusuo Okuma ◽  
Satoshi Watanabe
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Air Flow ◽  
Water Flow Rate ◽  
Phase Flow ◽  
Air Flow Rate ◽  
Operating Characteristics ◽  
Two Phase ◽  
Flow Pump

A centrifugal impeller, the pumping action of which could be highly kept even at an air-water two-phase flow condition of inlet void fraction more than 30% in the region of relatively high water flow rate, has been developed. In the present paper, the design concept of two-phase flow impeller is described, at first, with experimental results. The short bladed forward impeller with high outlet blade angle was decided to keep theoretical head higher even in two-phase flow condition and to disperse the air accumulating region on the suction blade surface by the water jet flow coming from the pressure side. Furthermore, the tandem arrangement of outer and inner rotating cascades with the same blade numbers was adopted to suppress the rotating stall phenomena appearing in the case of a single stage of outer cascade. It should be noted that these results were obtained with operating a boost pump installed upstream of mixing section of air and water, that is not an actual operation of two-phase flow pump. Secondly, the operating characteristics of this two-phase flow pump with change of air flow rate were investigated experimentally without operating the boost pump. As the trajectory of operating point with increasing air flow rate appears along the resistance curve of piping system, the impossibility of pumping occurs at lower air flow rate even though pump head takes a positive value at high air flow rate with increasing water flow rate. It is recognized that it is necessary to improve two-phase flow head characteristic curves in the region of low water flow rate to operate in wider two-phase flow conditions.

scholarly journals Experimental Study on Thermal Radiation Attenuation Using Water Mist of Twin-fluid Atomizer

2021 ◽  
Vol 35 (4) ◽  
pp. 24-32
Author(s):  
Jae Geun Jo ◽  
Chi Young Lee
Keyword(s):  
Thermal Radiation ◽  
Water Flow ◽  
Flow Rate ◽  
Air Flow ◽  
Water Flow Rate ◽  
Water Mist ◽  
Air Flow Rate ◽  
Radiation Attenuation ◽  
Rate Condition ◽  
Flow Rates

In this study, the thermal radiation attenuation performance of water mist was investigated using twin-fluid atomizers. The water and air flow rates of Small atomizer were 36~105 g/min and 10~30 L/min, whereas those of Large atomizer were 37~300 g/min and 20~60 L/min, respectively. In the present experimental range, the thermal radiation attenuation of Small atomizer and Large atomizer were 6.1~11.9% and 5.2~14.6%, respectively. With the increase in water and air flow rates, the thermal radiation attenuation increased, and under similar water and air flow rate conditions, Small atomizer showed higher thermal radiation attenuation than Large atomizer. Based on the present experimental data, it was found that the air (gas) discharge area is a potentially important factor in determining the thermal radiation attenuation performance. Additionally, through the analysis of thermal radiation attenuation per unit water flow rate, it was confirmed that the twin-fluid atomizer can result in higher thermal radiation attenuation than the single-fluid atomizer under the same water flow rate condition.

Generating Nitrate and Nitrite on Green Oak Lettuce in Hydroponic Farming by Plasma System

2021 ◽  
Vol 37 (1) ◽  
pp. 105-112
Author(s):  
Komgrit Leksakul ◽  
Norrapon Vichiansan ◽  
Pisit Kaewkham ◽  
Boonprathan Hattaphasu ◽  
Dheerawan Boonyawan
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
Reactive Nitrogen Species ◽  
Air Flow ◽  
Water Flow Rate ◽  
Plasma Discharge ◽  
Nitrogen Species ◽  
Air Flow Rate ◽  
Discharge System ◽  
Discharge Duration

HighlightsAbstract. In this study, we developed an effective methodology to determine the suitable plasma-based generating system of reactive nitrogen species (RNS) targeting hydroponic farming systems using a full factorial design with center points and blocking. A 2k with 2 blockings plus 2 center points design was employed in the experiment to develop an efficient analytical model for nitrogen solution concentration and hydroponic vegetable growth incorporating the plasma discharge system process parameters, including water flow rate, plasma discharge duration, and air flow rate. This study designed and constructed an air plasma discharge system with DC power supply. Thereafter, nitrogen solution was generated under a parameter conditions setting by the design of experiments (DOE) method. RNS solution, which contained nitrate (NO3-) and nitrite (NO2-) ions with P and K added, was passed through the hydroponic system for growing green oak lettuce. The most promising plasma-generated nitrogen solution parameters were obtained for this set up at a water flow rate of 6 L/min, discharge duration of 60 min, and activated air flow rate of 60 mL/min. Keywords: Nitrate, Nitrite, Plasma discharge, Reactive nitrogen species.

Experimental Characterization of a Modified Airlift Pump

2014 ◽  
Author(s):  
Afshin Goharzadeh ◽  
Keegan Fernandes
Keyword(s):  
Water Flow ◽  
Flow Rate ◽  
High Speed ◽  
Water Flow Rate ◽  
High Speed Photography ◽  
Two Phase ◽  
Inner Diameter ◽  
Airlift Pump ◽  
Flow Map ◽  
Churn Flow

This paper presents an experimental investigation on a modified airlift pump. Experiments were undertaken as a function of air-water flow rate for two submergence ratios (ε=0.58 and 0.74), and two different riser geometries (i) straight pipe with a constant inner diameter of 19 mm and (ii) enlarged pipe with a sudden expanded diameter of 19 to 32 mm. These transparent vertical pipes, of 1 m length, were submerged in a transparent rectangular tank (0.45×0.45×1.1 m3). The compressed air was injected into the vertical pipe to lift the water from the reservoir. The flow map regime is established for both configurations and compared with previous studies. The two phase air-water flow structure at the expansion region is experimentally characterized. Pipeline geometry is found to have a significant influence on the output water flow rate. Using high speed photography and electrical conductivity probes, new flow regimes, such as “slug to churn” and “annular to churn” flow, are observed and their influence on the output water flow rate and efficiency are discussed. These experimental results provide fundamental insights into the physics of modified airlift pump.

Air Entrainment and Bubble Generation by a Hydrofoil in a Turbulent Channel Flow

2019 ◽  
Author(s):  
Ichiro Kumagai ◽  
Kakeru Taguchi ◽  
Chiharu Kawakita ◽  
Tatsuya Hamada ◽  
Yuichi Murai
Keyword(s):  
Channel Flow ◽  
Flow Rate ◽  
High Speed ◽  
Air Flow ◽  
Air Entrainment ◽  
Air Bubbles ◽  
Air Flow Rate ◽  
Bubble Generation ◽  
Gas Liquid Flow ◽  
Entrained Air

Abstract Air entrainment and bubble generation by a hydrofoil bubble generator for ship drag reduction have been investigated using a small high-speed channel tunnel with the gap of 20 mm in National Maritime Research Institute (NMRI). A hydrofoil (NACA4412, chord length = 40 mm) was installed in the channel and an air induction pipe was placed above the hydrofoil. The flow rate of the entrained air was quantitatively measured by thermal air flow sensors at the inlet of the air induction pipe. The gas-liquid flow around the hydrofoil was visualized by a backlight method and recorded by a high-speed video camera. As the flow velocity in the channel increased, the negative pressure generated above the suction side of the hydrofoil lowered the hydrostatic pressure in the channel, then the atmospheric air was entrained into the channel flow. The entrained air was broken into small air bubbles by the turbulent flow in the channel. The threshold of air entrainment, the air flow rate, and gas-liquid flow pattern depends on Reynolds number, angle of attack (AOA), and hydrofoil type. We identified at least three modes of air entrainment behavior: intermittent air entrainment, stable air entrainment, and air entrainment with a ventilated cavity. At high flow speed in our experimental condition (9 m/s), a large volume of air bubbles was generated by this hydrofoil system (e.g. air flow rate was 50 l/min for NACA4412 at AOA 16 degrees), which has a high potential to reduce ship drag.

Sealing Effects of Squeeze Air Film

1986 ◽  
Vol 108 (4) ◽  
pp. 594-597 ◽  
Author(s):  
H. Takada ◽  
S. Kamigaichi ◽  
H. Miura
Keyword(s):  
Flow Rate ◽  
Vibration Amplitude ◽  
Ambient Pressure ◽  
Air Flow ◽  
Face Seal ◽  
Air Flow Rate ◽  
The Difference ◽  
Air Film ◽  
Theoretical Results ◽  
Good Agreement

The sealing effects of squeeze air film were analyzed experimentally and theoretically. The air flow rate and the sealed pressure were measured in a squeeze face seal. The air flow rate can be expressed as the difference between the flow rate by the pumping and the flow rate by the leakage. The air flow rate by the pumping increases proportionally to the square of the vibration amplitude of the surface, as does the sealed pressure. The air flow rate by the leakage increases proportionally to the pressure difference between the vessel pressure and the ambient pressure. The experimental results showed good agreement with the theoretical results.

Sign in / Sign up

Export Citation Format

Share Document