Experimental Study of Advanced Convective Cooling Techniques for Combustor Liners

2008 ◽  
Author(s):  
Michael Maurer ◽  
Uwe Ruedel ◽  
Michael Gritsch ◽  
Jens von Wolfersdorf
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Flow Field ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Transfer Enhancement ◽  
Number Range ◽  
Convective Cooling

An experimental study was conducted to determine the heat transfer performance of advanced convective cooling techniques at the typical conditions found in a backside cooled combustion chamber. For these internal cooling channels, the Reynolds number is usually found to be above the Reynolds number range covered by available databases in the open literature. As possible candidates for an improved convective cooling configuration in terms of heat transfer augmentation and acceptable pressure drops, W-shaped and WW-shaped ribs were considered for channels with a rectangular cross section. Additionally, uniformly distributed hemispheres were investigated. Here, four different roughness spacings were studied to identify the influence on friction factors and the heat transfer enhancement. The ribs and the hemispheres were placed on one channel wall only. Pressure losses and heat transfer enhancement data for all test cases are reported. To resolve the heat transfer coefficient, a transient thermocromic liquid crystal technique was applied. Additionally, the area-averaged heat transfer coefficient on the W-shaped rib itself was observed using the so-called lumped-heat capacitance method. To gain insight into the flow field and to reveal the important flow field structures, numerical computations were conducted with the commercial code FLUENT™.

Applied Pulsed Flow for Single-Phase Convective Heat Transfer Enhancement in a Laminar Flow Cooling System

2008 ◽  
Author(s):  
Bolaji O. Olayiwola ◽  
Gerhard Schaldach ◽  
Peter Walzel
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Cooling System ◽  
Transfer Enhancement ◽  
Flow Rates ◽  
The Heat Transfer Coefficient

Experimental and CFD studies were performed to investigate the enhancement of convective heat transfer in a laminar cooling system using flow pulsation in a flat channel with series of regular spaced fins. Glycerol-water mixtures with dynamic viscosities in the range of 0.001 kg/ms–0.01 kg/ms were used. A steady flow Reynolds number in the laminar range of 10 < Re < 1200 was studied. The amplitudes of the applied pulsations are in the range of 0.25 < A < 0.55 mm and the frequency range is 10 < f < 60 Hz. Two different cooling devices with active length L = 450 mm and 900 mm were investigated. CFD simulations were performed on a parallel-computer (Linux-cluster) using the software suit CFX11 from ANSYS GmbH, Germany. The rate of cooling was found to be significant at moderate low net flow rates. In general, no significant heat transfer enhancement at very low and high flow rates was obtained in compliance with the experimental data. The heat transfer coefficient was found to increase with increasing Prandtl number Pr at constant oscillation Reynolds number Reosc whereas the ratio of the hydraulic diameter to the length of the channel dh/L has insignificant effect on the heat transfer coefficient. This is due to enhanced fluid mixing. CFD results allow for performance predictions of different geometries and flow conditions.

Heat transfer performance of steam/air flow in inverted V-shaped rib-roughened channels

2021 ◽  
pp. 095765092110161
Author(s):  
Chao Ma ◽  
Bing Ge
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Air Flow ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Ribbed Channel

The heat transfer performance of steam and air flow in a rough rectangular channel with different inverted V-shaped ribs was investigated by infrared thermal imaging technology. Under the conditions that the Reynolds number is in the range of 4000–15,000, the effects of the rib angle on the heat transfer enhancement of the two coolants were obtained. The rib pitch ratio of the flow channel is 10, the ratio of the rib height to the channel hydraulic diameter is 0.078, and the inverted V-shaped rib angle varies from 45° to 90°. The results show that in the inverted V-shaped ribbed channel, the Nu number on both sides of the channel is greatly increased, while the Nu number in the middle of the channel is lower. The local Nu distribution on the surface of the ribbed channel is highly related to the shape of the rib. For different medium cooling, the value and unevenness of the heat transfer coefficient are different, but the shape of the high and low heat transfer coefficient distribution is hardly affected. The heat transfer of both coolants increases as the rib angle decreases from 90° to 45°. Compared with air flow, steam flow cooling shows higher convective heat transfer enhancement. For rib angles of 45°, 60°, 75°, and 90°, under the operating condition of the Reynolds number = 12,000, the area-averaged Nusselt numbers of the steam flow is 23.6%, 27.4% and 13.9% higher than that of the air flow, respectively. Based on the experimental heat transfer data, the correlation in terms of the Reynolds number and the rib angle was developed, which is used to estimate the Nu number for steam and air cooling in the inverted V-shaped rib-roughness channels.

Heat Transfer Enhancement by Insertion of Vortex Generators in Electronic Chip Cooling: A Numerical Study

2017 ◽  
Author(s):  
Mohammad Rejaul Haque ◽  
Amy Rachel Betz
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Aspect Ratio ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Vortex Generators ◽  
Transfer Enhancement ◽  
Maximum Heat

The present work represents a 2-D numerical investigation of forced convection heat transfer over three electronic blocks (silicon chip) in an inline arrangement with elliptical shaped vortex generators (VG-copper made) placed on top of the channel, for a range of Reynolds numbers. The block is prescribed with a 1,000 W/m2 heat flux due to heating of the electronic components installed in the CPU casing. The results show that, vortex generators could effectively enhance the heat transfer in the channel. Subsequently, the effects of Reynolds number (from 500 to 1050), the number of vortex generators (baseline, 1, 2 and 3), aspect ratio of heated block (0.125, 0.15, 0.22), and aspect ratio of vortex generators (0.3125, 0.4, 0.5) on the heat transfer and fluid flow characteristics are examined. The characteristics of the performance parameters are studied numerically with the aid of computational fluid dynamics (CFD). The 3 VG demonstrates nearly 28.35% enhancement of Nusselt number compared to the 1 VG case at Re = 479. The change in pressure drop is less at low Reynolds number compared to higher Reynolds number respective to other parameters. Increasing the aspect ratio of the block increases the convection coefficient while decreasing aspect ratio of VG increases heat transfer coefficient. This enhancement is less significant for the third block as the cooling effect is predominant close to the channel inlet. Increasing consecutive distance between the blocks, enhances the heat transfer coefficient with the penalty of additional pressure drop. However, parametric studies are conducted for the maximum heat transfer enhancement.

scholarly journals Toward improved heat dissipation of the turbulent regime over backward-facing step for the AL2O3-water nanofluids: An experimental approach

2019 ◽  
Vol 23 (3 Part B) ◽  
pp. 1779-1789 ◽  
Author(s):  
Syed Ahmed ◽  
Salim Kazi ◽  
Ghulamullah Khan ◽  
Mohd Zubir ◽  
Mahidzal Dahari ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Turbulent Regime ◽  
Al2o3 Nanoparticles ◽  
Backward Facing Step ◽  
Constant Weight ◽  
Weight Concentration

Experimental study of nanofluid flow and heat transfer to fully developed turbulent forced convection flow in a uniformly heated tubular horizontal backward-facing step has reported in the present study. To study the forced convective heat transfer coefficient in the turbulent regime, an experimental study is performed at a different weight concentration of Al2O3 nanoparticles. The experiment had conducted for water and Al2O3 -water nanofluid for the concentration range of 0 to 0.1 wt.% and Reynolds number of 4000 to 16000. The average heat transfer coefficient ratio increases significantly as Reynolds number increasing, increased from 9.6% at Reynolds number of 4000 to 26.3% at Reynolds number of 16000 at the constant weight concentration of 0.1%. The Al2O3 water nanofluid exhibited excellent thermal performance in the tube with a backwardfacing step in comparison to distilled water. However, the pressure losses increased with the increase of the Reynolds number and/or the weight concentrations, but the enhancement rates were insignificant.

An Experimental Investigation of Structured Roughness Effect on Heat Transfer During Single-Phase Liquid Flow at Microscale

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Ting-Yu Lin ◽  
Satish G. Kandlikar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Enhancement Factor ◽  
Roughness Element ◽  
Hydraulic Diameter ◽  
Transfer Enhancement ◽  
Roughness Elements ◽  
The Heat Transfer Coefficient

The effect of structured roughness on the heat transfer of water flowing through minichannels was experimentally investigated in this study. The test channels were formed by two 12.7 mm wide × 94.6 mm long stainless steel strips. Eight structured roughness elements were generated using a wire electrical discharge machining (EDM) process as lateral grooves of sinusoidal profile on the channel walls. The height of the roughness structures ranged from 18 μm to 96 μm, and the pitch was varied from 250 μm to 400 μm. The hydraulic diameter of the rectangular flow channels ranged from 0.71 mm to 1.87 mm, while the constricted hydraulic diameter (obtained by using the narrowest flow gap) ranged from 0.68 mm to 1.76 mm. After accounting for heat losses from the edges and end sections, the heat transfer coefficient for smooth channels was found to be in good agreement with the conventional correlations in the laminar entry region as well as in the laminar fully developed region. All roughness elements were found to enhance the heat transfer. In the ranges of parameters tested, the roughness element pitch was found to have almost no effect, while the heat transfer coefficient was significantly enhanced by increasing the roughness element height. An earlier transition from laminar to turbulent flow was observed with increasing relative roughness (ratio of roughness height to hydraulic diameter). For the roughness element designated as B-1 with a pitch of 250 μm, roughness height of 96 μm and a constricted hydraulic diameter of 690 μm, a maximum heat transfer enhancement of 377% was obtained, while the corresponding friction factor increase was 371% in the laminar fully developed region. Comparing different enhancement techniques reported in the literature, the highest roughness element tested in the present work resulted in the highest thermal performance factor, defined as the ratio of heat transfer enhancement factor (over smooth channels) and the corresponding friction enhancement factor to the power 1/3.

Convective Heat Transfer Distribution on the Surface of an Electronic Package

1994 ◽  
Vol 116 (1) ◽  
pp. 49-54 ◽  
Author(s):  
R. A. Wirtz ◽  
Ashok Mathur
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Average Heat Transfer Coefficient ◽  
Number Range ◽  
Electronic Package ◽  
Average Heat

Measurements of the distribution of convective heat transfer over the five exposed faces of a low profile electronic package are described. The package, of square planform and length-to-height ratio, L/a = 6, is part of a regular array of such elements attached to one wall of a low aspect ratio channel. The coolant is air, and experiments are described for the Reynolds number range, 3000<Re<7000. The average heat transfer coefficient for the top face is found to be nearly equal to the overall average heat transfer coefficient for the element. The average heat transfer coefficient for the upstream face and two side faces are higher than the overall average by approximately 30–40 percent and 20–30 percent, respectively while that for the downstream face is 20–30 percent less than the overall average. Furthermore, the distribution in local heat transfer coefficient over the five surfaces of the element is approximately independent of variations in Reynolds number.

Phase Change Material Particulate Flow Through a Rectangular Channel: Effect of Parachute-Shaped Particles on the Heat Transfer

2011 ◽  
Author(s):  
Laura Small ◽  
Fatemeh Hassanipour
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Phase Change ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Phase Change Material ◽  
Volume Fraction ◽  
Particulate Flow ◽  
Transfer Enhancement ◽  
Change Material

This study presents numerical simulations of forced convection with parachute-shaped encapsulated phase-change material particles in water, flowing through a square cross-section duct with top and bottom iso-flux surfaces. The system is inspired by the gas exchange process in the alveolar capillaries between the red blood cells (RBC) and the lung tissue. The numerical model was developed for the motion of elongated encapsulated phase change particles along a channel in a particulate flow where particle diameters are comparable with the channel height. Results of the heat transfer enhancement for the parachute-shaped particles are compared with the circular particles. Results reveal that the key role in heat transfer enhancement is the snugness movement of the particles and the parachute-shaped geometry yields small changes in heat transfer coefficient when compared to the circular ones. The effects of various parameters including particle diameter and volume-fraction, as well as fluid speed, on the heat transfer coefficient is investigated and reported in this paper.

Condensation Pressure Drop and Heat Transfer in 5-mm-OD Micro-Fin Tubes

2012 ◽  
Author(s):  
Wei Li ◽  
Dan Huang ◽  
Zan Wu ◽  
Hong-Xia Li ◽  
Zhao-Yan Zhang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Condensation Heat Transfer ◽  
Transfer Enhancement ◽  
Mass Fluxes ◽  
Fin Tubes ◽  
Condensation Heat Transfer Coefficient

An experimental investigation was performed for convective condensation of R410A inside four micro-fin tubes with the same outside diameter (OD) 5 mm and helix angle 18°. Data are for mass fluxes ranging from about 180 to 650 kg/m2s. The nominal saturation temperature is 320 K, with inlet and outlet qualities of 0.8 and 0.1, respectively. The results suggest that Tube 4 has the best thermal performance for its largest condensation heat transfer coefficient and relatively low pressure drop penalty. Condensation heat transfer coefficient decreases at first and then increases or flattens out gradually as G decreases. This complex mass-flux effect may be explained by the complex interactions between micro-fins and fluid. The heat transfer enhancement mechanism is mainly due to the surface area increase over the plain tube at large mass fluxes, while liquid drainage and interfacial turbulence play important roles in heat transfer enhancement at low mass fluxes. In addition, the experimental data was analyzed using seven existing pressure-drop and four heat-transfer models to verify their respective accuracies.

Effect of Heat Flux on Pool Boiling Heat Transfer Enhancement (Numerical Investigation Approach)

2020 ◽  
Author(s):  
T. S. Mogaji ◽  
O. A. Sogbesan ◽  
Tien-Chien Jen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Enhancement ◽  
Numerical Investigation ◽  
Boiling Heat Transfer ◽  
Pool Boiling ◽  
Nucleate Boiling ◽  
Transfer Enhancement

Abstract This study presents numerical investigation results of heat flux effect on pool boiling heat transfer enhancement during nucleate boiling heat transfer of water. The simulation was performed for five different heated surfaces such as: brass, copper, mild steel, stainless steel and aluminum using ANSYS simulation software at 1 atmospheric pressure. The samples were heated in a domain developed for bubble growth during nucleate boiling process under the same operational condition of applied heat flux ranged from 100 to 1000 kW/m2 and their corresponding heat transfer coefficient was obtained numerically. Obtained experimental data of other authors from the open literature result is in close agreement with the simulated data, thus confirming the validity of the CFD simulation method used in this study. It is found that heat transfer coefficient increases with increasing heat flux. The results revealed that in comparison to other materials tested, better heat transfer performance up to 38.5% and 7.11% is observed for aluminum and brass at lower superheated temperature difference conditions of 6.96K and 14.01K respectively. This behavior indicates better bubble development and detachment capability of these heating surface materials and could be used in improving the performance of thermal devices toward producing compact and miniaturized equipment.

Sign in / Sign up

Export Citation Format

Share Document