Steady VGJ Flow Control on a Highly Loaded Transonic LPT Cascade: Effects of Compressibility and Roughness

2014 ◽  
Author(s):  
Chiara Bernardini ◽  
Stuart I. Benton ◽  
John D. Lee ◽  
Jeffrey P. Bons ◽  
Jen-Ping Chen ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Flow Control ◽  
High Speed ◽  
Operating Conditions ◽  
Control Performance ◽  
Blowing Ratio ◽  
Number Distribution ◽  
Turbulent Separation ◽  
Mach Number Distribution

A new high-speed linear cascade has been developed for low-pressure turbine (LPT) studies at The Ohio State University. A compressible LPT profile is tested in the facility and its baseline performance at different operating conditions is assessed by means of isentropic Mach number distribution and wake total pressure losses. Active flow control is implemented through a spanwise row of vortex-generator jets (VGJs) located at 60% chord on the suction surface. The purpose of the study is to document the effectiveness of VGJ flow control in high-speed compressible flow. The effect on shock-induced separation is assessed by Mach number distribution, wake loss surveys and shadowgraph. Pressure Sensitive Paint is applied to understand the three dimensional flow and shock pattern developing from the interaction of the skewed jets and the main flow. Data show that with increasing blowing ratio the losses are first decreased due to separation reduction, but losses connected to compressibility effects become stronger due to increased passage shock strength and jet orifice choking; therefore the optimum blowing ratio is a tradeoff between these counteracting effects. The effect of added surface roughness on the uncontrolled flow and on flow control behavior is also investigated. At lower Mach number turbulent separation develops on the rough surface and a different flow control performance is observed. Steady VGJs appear to have control authority even on a turbulent separation but higher blowing ratios are required compared to incompressible flow experiments reported elsewhere. Overall, the results show a high sensitivity of steady VGJs control performance and optimum blowing ratio to compressibility and surface roughness.

Steady Vortex-Generator Jet Flow Control on a Highly Loaded Transonic Low-Pressure Turbine Cascade: Effects of Compressibility and Roughness

2014 ◽  
Vol 136 (11) ◽  
Author(s):  
Chiara Bernardini ◽  
Stuart I. Benton ◽  
John D. Lee ◽  
Jeffrey P. Bons ◽  
Jen-Ping Chen ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Flow Control ◽  
High Speed ◽  
Vortex Generator ◽  
Control Performance ◽  
Low Pressure Turbine ◽  
Blowing Ratio ◽  
Turbulent Separation ◽  
Mach Number Distribution

A new high-speed linear cascade has been developed for low-pressure turbine (LPT) studies at The Ohio State University. A compressible LPT profile is tested in the facility and its baseline performance at different operating conditions is assessed by means of isentropic Mach number distribution and wake total pressure losses. Active flow control is implemented through a spanwise row of vortex-generator jets (VGJs) located at 60% chord on the suction surface. The purpose of the study is to document the effectiveness of VGJ flow control in high-speed compressible flow. The effect on shock-induced separation is assessed by Mach number distribution, wake loss surveys and shadowgraph. Pressure sensitive paint (PSP) is applied to understand the three dimensional flow and shock pattern developing from the interaction of the skewed jets and the main flow. Data show that with increasing blowing ratio, the losses are first decreased due to separation reduction, but losses connected to compressibility effects become stronger due to increased passage shock strength and jet orifice choking; therefore, the optimum blowing ratio is a tradeoff between these counteracting effects. The effect of added surface roughness on the uncontrolled flow and on flow control behavior is also investigated. At lower Mach number, turbulent separation develops on the rough surface and a different flow control performance is observed. Steady VGJs appear to have control authority even on a turbulent separation but higher blowing ratios are required compared to incompressible flow experiments reported elsewhere. Overall, the results show a high sensitivity of steady VGJs control performance and optimum blowing ratio to compressibility and surface roughness.

scholarly journals Aerodynamic Losses in Turbines with and without Film Cooling, as Influenced by Mainstream Turbulence, Surface Roughness, Airfoil Shape, and Mach Number

2012 ◽  
Vol 2012 ◽  
pp. 1-28 ◽  
Author(s):  
Phil Ligrani
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Film Cooling ◽  
Total Pressure ◽  
High Speed ◽  
Density Ratio ◽  
Aerodynamic Loss ◽  
Pressure Losses ◽  
Loss Coefficients ◽  
Exit Mach Number

The influences of a variety of different physical phenomena are described as they affect the aerodynamic performance of turbine airfoils in compressible, high-speed flows with either subsonic or transonic Mach number distributions. The presented experimental and numerically predicted results are from a series of investigations which have taken place over the past 32 years. Considered are (i) symmetric airfoils with no film cooling, (ii) symmetric airfoils with film cooling, (iii) cambered vanes with no film cooling, and (iv) cambered vanes with film cooling. When no film cooling is employed on the symmetric airfoils and cambered vanes, experimentally measured and numerically predicted variations of freestream turbulence intensity, surface roughness, exit Mach number, and airfoil camber are considered as they influence local and integrated total pressure losses, deficits of local kinetic energy, Mach number deficits, area-averaged loss coefficients, mass-averaged total pressure loss coefficients, omega loss coefficients, second law loss parameters, and distributions of integrated aerodynamic loss. Similar quantities are measured, and similar parameters are considered when film-cooling is employed on airfoil suction surfaces, along with film cooling density ratio, blowing ratio, Mach number ratio, hole orientation, hole shape, and number of rows of holes.

Mach number distribution over the axis of supersonic underexpanded jets

1968 ◽  
Vol 15 (6) ◽  
pp. 1153-1157 ◽  
Author(s):  
Yu. P. Finat'ev ◽  
L. A. Shcherbakov ◽  
N. M. Gorskaya
Keyword(s):  
Mach Number ◽  
Underexpanded Jets ◽  
Number Distribution ◽  
Mach Number Distribution

Design Method for Subsonic and Transonic Cascade With Prescribed Mach Number Distribution

1992 ◽  
Vol 114 (3) ◽  
pp. 553-560 ◽  
Author(s):  
O. Le´onard ◽  
R. A. Van den Braembussche
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
Pressure Distribution ◽  
Velocity Component ◽  
Design Method ◽  
Normal Velocity ◽  
Flow Solver ◽  
Number Distribution ◽  
Mach Number Distribution ◽  
Transonic Cascade

A iterative procedure for blade design, using a time marching procedure to solve the unsteady Euler equations in the blade-to-blade plane, is presented. A flow solver, which performs the analysis of the flow field for a given geometry, is transformed into a design method. This is done by replacing the classical slip condition (no normal velocity component) by other boundary conditions, in such a way that the required pressure or Mach number distribution may be imposed directly on the blade. The unknowns are calculated on the blade wall using the so-called compatibility relations. Since the blade shape is not compatible with the required pressure distribution, a nonzero velocity component normal to the blade wall evolves from the new flow calculation. The blade geometry is then modified by resetting the wall parallel to the new flow field, using a transpiration technique, and the procedure is repeated until the calculated pressure distribution has converged to the required one. Examples for both subsonic and transonic flows are presented and show a rapid convergence to the geometry required for the desired Mach number distribution. An important advantage of the present method is the possibility to use the same code for the design and the analysis of a blade.

Boundary layer suction for high-speed air intakes: A review

2018 ◽  
Vol 233 (9) ◽  
pp. 3459-3481 ◽  
Author(s):  
Javad Sepahi-Younsi ◽  
Behzad Forouzi Feshalami ◽  
Seyed Reza Maadi ◽  
Mohammad Reza Soltani
Keyword(s):  
Boundary Layer ◽  
Mach Number ◽  
Flow Control ◽  
High Speed ◽  
Control Methods ◽  
Slant Angle ◽  
Boundary Layer Suction ◽  
Recent Developments

The paper summarizes recent developments in boundary layer suction for high-speed air intakes. Bleed has been efficiently used in supersonic and hypersonic intakes for three primary reasons: to improve the performance of the intake, to reduce the starting Mach number of the intake, and to postpone the onset of buzz oscillations. A bleed system has many characteristics such as the bleed entrance and exit areas, bleed entrance slant angle and position, and bleed type (slot or porous and ram-scoop or flush). Each of these parameters has significant impacts on the intake performance and stability that have been reviewed in this study. In addition, the effectiveness of other flow control methods has been compared with the bleed method.

Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: High-Speed Validation

2006 ◽  
Vol 129 (2) ◽  
pp. 340-347 ◽  
Author(s):  
Maria Vera ◽  
Xue Feng Zhang ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Surface Finish ◽  
High Speed ◽  
Reynolds Numbers ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Transition Mechanism ◽  
Low Reynolds

This paper presents the second part of an investigation of the combined effects of unsteadiness and surface roughness on an aft-loaded ultra-high-lift low-pressure turbine (LPT) profile at low Reynolds numbers. The investigation has been performed using low- and high-speed cascade facilities. The low- and high-speed profiles have been designed to have the same normalized isentropic Mach number distribution. The low-speed results have been presented in the first part (Zhang, Vera, Hodson, and Harvey, 2006, ASME J. Turbomach., 128, pp. 517–527). The current paper examines the effect of different surface finishes on an aft-loaded ultra-high-lift LPT profile at Mach and Reynolds numbers representative of LPT engine conditions. The surface roughness values are presented along with the profile losses under steady and unsteady inflow conditions. The results show that the use of a rough surface finish can be used to reduce the profile loss. In addition, the results show that the same quantitative values of losses are obtained at high- and low-speed flow conditions. The latter proves the validity of the low-speed approach for ultra-high-lift profiles for the case of an exit Mach number of the order of 0.64. Hot-wire measurements were carried out to explain the effect of the surface finish on the wake-induced transition mechanism.

The Effect of Surface Roughness on Efficiency of Low Pressure Turbines

2013 ◽  
Vol 136 (6) ◽  
Author(s):  
Raúl Vázquez ◽  
Diego Torre
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Slope Angle ◽  
Low Pressure ◽  
Operating Conditions ◽  
Specific Work ◽  
Pressure Losses ◽  
Comparison Of The Results ◽  
Very High ◽  
Effect Of Surface

The effect of surface roughness on the efficiency of low pressure turbines (LPTs) was experimentally investigated in a multistage turbine high-speed rig. The rig consisted of three stages of a state-of-the-art LPT. The stages were characterized by a very high wall-slope angle, reverse cut-off design, very high lift, and very high aspect ratio airfoils. Two sets of airfoils (both stators and rotors) were tested. The first set was made of airfoils with a roughness size of 0.7 μm Ra (25–35 × 10−5 ks/Cm), which was representative of LPT polished airfoils. The surface finish for the second set of airfoils was 1.8 μm Ra for blades and 2.5 μm Ra for stators (approximately 90 × 10−5 in terms of ks/Cm for both stators and blades). The resulting roughness of this set was representative of “as-cast” airfoils of low pressure turbines. The airfoil geometries, velocity triangles, leading and trailing edge locations, and flowpath were maintained between both sets. They were tested with the same instrumentation and at the same operating conditions with the intention of determining the isolated impact of the surface roughness on the overall efficiency. The turbine characteristics: sensitivity to speed, specific work, Reynolds number, and purge flows, were obtained for both sets. The comparison of the results suggests that the efficiency and capacity of both types of airfoils exhibit the same behavior. No significant differences in the results can be distinguished for the range of operating conditions in this study. The results agree with previous studies of distributed roughness in turbines: the use of as-cast rough airfoils in some low pressure turbines at high altitude does not introduce additional pressure losses.

Aerodynamic Losses of a Cambered Turbine Vane: Influences of Surface Roughness and Freestream Turbulence Intensity

2005 ◽  
Author(s):  
Qiang Zhang ◽  
Phillip M. Ligrani
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Turbulence Intensity ◽  
Suction Side ◽  
Freestream Turbulence ◽  
Smooth Test ◽  
Profile Losses ◽  
Turbine Vane ◽  
Mach Number Distribution ◽  
Aerodynamic Losses

The effects of surface roughness and freestream turbulence level on the aerodynamic performance of a turbine vane are experimentally investigated. Wake profiles are measured with three different freestream turbulence intensity levels (1.1%, 5.4% and 7.7%) at two different locations downstream of the test vane trailing edge (one and 0.25 axial chord lengths). Chord Reynolds number based on exit flow conditions is 0.9 × 106. The Mach number distribution and the test vane configuration both match arrangements employed in an industrial application. Four cambered vanes with different surface roughness levels are employed in this study. Effects of surface roughness on the vane pressure side on the profile losses are relatively small compared with suction side roughness. Overall effects of turbulence on local wake deficits of total pressure, Mach number, and kinetic energy are almost negligible in most parts of the wake produced by the smooth test vane, except that higher freestream losses are present at higher turbulence intensity levels. Profiles produced by test vanes with rough surfaces show apparent lower peak values in the center of the wake. Integrated Aerodynamic Losses (IAL) and area-averaged loss coefficient YA are also presented and compared with results from other research groups.

Sign in / Sign up

Export Citation Format

Share Document