scholarly journals Flow Inhomogeneities in a Realistic Aeronautical Gas-Turbine Combustor: Formation, Evolution and Indirect Noise

2018 ◽  
Author(s):  
Andrea Giusti ◽  
Luca Magri ◽  
Marco Zedda
Keyword(s):  
Gas Turbines ◽  
Transfer Functions ◽  
Guide Vane ◽  
Flame Structure ◽  
Combustion Noise ◽  
Moment Closure ◽  
Combustion Model ◽  
Conditional Moment ◽  
Eddy Simulation ◽  
Nozzle Guide

Indirect noise generated by the acceleration of combustion inhomogeneities is an important aspect in the design of aeroengines because of its impact on the overall noise emitted by an aircraft and the possible contribution to combustion instabilities. In this study, a realistic rich-quench-lean combustor is numerically investigated, with the objective of quantitatively analyzing the formation and evolution of flow inhomogeneities and determine the level of indirect combustion noise in the nozzle guide vane (NGV). Both entropy and compositional noise are calculated in this work. A high-fidelity numerical simulation of the combustion chamber, based on the Large-Eddy Simulation (LES) approach with the Conditional Moment Closure (CMC) combustion model, is performed. The contributions of the different air streams to the formation of flow inhomogeneities are pinned down and separated with seven dedicated passive scalars. LES-CMC results are then used to determine the acoustic sources to feed an NGV aeroacoustic model, which outputs the noise generated by entropy and compositional inhomogeneities. Results show that non-negligible fluctuations of temperature and composition reach the combustor’s exit. Combustion inhomogeneities originate both from finite-rate chemistry effects and incomplete mixing. In particular, the role of mixing with dilution and liner air flows on the level of combustion inhomogeneities at the combustor’s exit is highlighted. The species that most contribute to indirect noise are identified and the transfer functions of a realistic NGV are computed. The noise level indicates that indirect noise generated by temperature fluctuations is larger that the indirect noise generated by compositional inhomogeneities, although the latter is not negligible and is expected to become louder in supersonic nozzles. It is also shown that relatively small fluctuations of the local flame structure can lead to significant variations of the nozzle transfer function, whose gain increases with the Mach number. This highlights the necessity of an on-line solution of the local flame structure, which is performed in this paper by CMC, for an accurate prediction of the level of compositional noise. This study opens new possibilities for the identification, separation and calculation of the sources of indirect combustion noise in realistic aeronautical gas turbines.

scholarly journals Flow Inhomogeneities in a Realistic Aeronautical Gas-Turbine Combustor: Formation, Evolution, and Indirect Noise

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Andrea Giusti ◽  
Luca Magri ◽  
Marco Zedda
Keyword(s):  
Gas Turbines ◽  
Transfer Functions ◽  
Guide Vane ◽  
Flame Structure ◽  
Combustion Noise ◽  
Moment Closure ◽  
Combustion Model ◽  
Conditional Moment ◽  
Eddy Simulation ◽  
Aero Engines

Indirect noise generated by the acceleration of combustion inhomogeneities is an important aspect in the design of aero-engines because of its impact on the overall noise emitted by an aircraft and the possible contribution to combustion instabilities. In this study, a realistic rich-quench-lean (RQL) combustor is numerically investigated, with the objective of quantitatively analyzing the formation and evolution of flow inhomogeneities and determining the level of indirect combustion noise in the nozzle guide vane (NGV). Both entropy and compositional noise are calculated in this work. A high-fidelity numerical simulation of the combustion chamber, based on the large-eddy simulation (LES) approach with the conditional moment closure (CMC) combustion model, is performed. The contributions of the different air streams to the formation of flow inhomogeneities are pinned down and separated with seven dedicated passive scalars. LES-CMC results are then used to determine the acoustic sources to feed an NGV aeroacoustic model, which outputs the noise generated by entropy and compositional inhomogeneities. Results show that non-negligible fluctuations of temperature and composition reach the combustor's exit. Combustion inhomogeneities originate both from finite-rate chemistry effects and incomplete mixing. In particular, the role of mixing with dilution and liner air flows on the level of combustion inhomogeneities at the combustor's exit is highlighted. The species that most contribute to indirect noise are identified and the transfer functions of a realistic NGV are computed. The noise level indicates that indirect noise generated by temperature fluctuations is larger than the indirect noise generated by compositional inhomogeneities, although the latter is not negligible and is expected to become louder in supersonic nozzles. It is also shown that relatively small fluctuations of the local flame structure can lead to significant variations of the nozzle transfer function, whose gain increases with the Mach number. This highlights the necessity of an on-line solution of the local flame structure, which is performed in this paper by CMC, for an accurate prediction of the level of compositional noise. This study opens new possibilities for the identification, separation, and calculation of the sources of indirect combustion noise in realistic aeronautical gas turbines.

Large Eddy Simulation of an Enclosed Turbulent Reacting Methane Jet With the Tabulated Premixed Conditional Moment Closure Method

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Carlos Velez ◽  
Scott Martin ◽  
Aleksander Jemcov ◽  
Subith Vasu
Keyword(s):  
Turbulent Combustion ◽  
Moment Closure ◽  
Scalar Dissipation ◽  
Combustion Model ◽  
Conditional Moment ◽  
Eddy Simulation ◽  
Conditional Moment Closure ◽  
Major Species ◽  
Large Eddy ◽  
Closure Method

The tabulated premixed conditional moment closure (T-PCMC) method has been shown to provide the capability to model turbulent, premixed methane flames with detailed chemistry and reasonable runtimes in Reynolds-averaged Navier–Stokes (RANS) environment by Martin et al. (2013, “Modeling an Enclosed, Turbulent Reacting Methane Jet With the Premixed Conditional Moment Closure Method,” ASME Paper No. GT2013-95092). Here, the premixed conditional moment closure (PCMC) method is extended to large eddy simulation (LES). The new model is validated with the turbulent, enclosed reacting methane backward facing step data from El Banhawy et al. (1983, “Premixed, Turbulent Combustion of a Sudden-Expansion Flow,” Combust. Flame, 50, pp. 153–165). The experimental data have a rectangular test section at atmospheric pressure and temperature with an inlet velocity of 10.5 m/s and an equivalence ratio of 0.9 for two different step heights. Contours of major species, velocity, and temperature are provided. The T-PCMC model falls into the class of table lookup turbulent combustion models in which the combustion model is solved offline over a range of conditions and stored in a table that is accessed by the computational fluid dynamic (CFD) code using three controlling variables: the reaction progress variable (RPV), variance, and local scalar dissipation rate. The local scalar dissipation rate is used to account for the affects of the small-scale mixing on the reaction rates. A presumed shape beta function probability density function (PDF) is used to account for the effects of subgrid scale (SGS) turbulence on the reactions. SGS models are incorporated for the scalar dissipation and variance. The open source CFD code OpenFOAM is used with the compressible Smagorinsky LES model. Velocity, temperature, and major species are compared to the experimental data. Once validated, this low “runtime” CFD turbulent combustion model will have great utility for designing the next generation of lean premixed (LPM) gas turbine combustors.

scholarly journals Investigation of Flame Structure and Soot Formation in a Single Sector Model Combustor Using Experiments and Numerical Simulations Based on the Large Eddy Simulation/Conditional Moment Closure Approach

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Andrea Giusti ◽  
Epaminondas Mastorakos ◽  
Christoph Hassa ◽  
Johannes Heinze ◽  
Eggert Magens ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Soot Formation ◽  
Flame Structure ◽  
Moment Closure ◽  
Conditional Moment ◽  
Lean Burn ◽  
Eddy Simulation ◽  
Conditional Moment Closure ◽  
Soot Precursors ◽  
Large Eddy

In this work, a single sector lean burn model combustor operating in pilot only mode has been investigated using both experiments and computations with the main objective of analyzing the flame structure and soot formation at conditions relevant to aero-engine applications. Numerical simulations were performed using the large eddy simulation (LES) approach and the conditional moment closure (CMC) combustion model with detailed chemistry and a two-equation model for soot. The CMC model is based on the time-resolved solution of the local flame structure and allows to directly take into account the phenomena associated to molecular mixing and turbulent transport, which are of great importance for the prediction of emissions. The rig investigated in this work, called big optical single sector rig, allows to test real scale lean burn injectors. Experiments, performed at elevated pressure and temperature, corresponding to engine conditions at part load, include planar laser-induced fluorescence of OH (OH-PLIF) and phase Doppler anemometry (PDA) and have been complemented with new laser-induced incandescence (LII) measurements for soot location. The wide range of measurements available allows a comprehensive analysis of the primary combustion region and can be exploited to further assess and validate the LES/CMC approach to capture the flame behavior at engine conditions. It is shown that the LES/CMC approach is able to predict the main characteristics of the flame with a good agreement with the experiment in terms of flame shape, spray characteristics and soot location. Finite-rate chemistry effects appear to be very important in the region close to the injection location leading to the lift-off of the flame. Low levels of soot are observed immediately downstream of the injector exit, where a high amount of vaporized fuel is still present. Further downstream, the fuel vapor disappears quite quickly and an extended region characterized by the presence of pyrolysis products and soot precursors is observed. The strong production of soot precursors together with high soot surface growth rates lead to high values of soot volume fraction in locations consistent with the experiment. Soot oxidation is also very important in the downstream region resulting in a decrease of the soot level at the combustor exit. The results show a very promising capability of the LES/CMC approach to capture the main characteristics of the flame, soot formation, and location at engine relevant conditions. More advanced soot models will be considered in future work in order to improve the quantitative prediction of the soot level.

Assessment of the Indirect Combustion Noise Generated in a Transonic High-Pressure Turbine Stage

2015 ◽  
Author(s):  
Dimitrios Papadogiannis ◽  
Florent Duchaine ◽  
Laurent Gicquel ◽  
Gaofeng Wang ◽  
Stéphane Moreau ◽  
...  
Keyword(s):  
High Pressure ◽  
Acoustic Waves ◽  
Gas Turbines ◽  
Guide Vane ◽  
Combustion Noise ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Noise Generation ◽  
Turbine Stage ◽  
High Pressure Turbine

Indirect combustion noise, generated by the acceleration and distortion of entropy waves through the turbine stages, has been shown to be the dominant noise source of gas turbines at low-frequencies and to impact the thermoacoustic behavior of the combustor. In the present work, indirect combustion noise generation is evaluated in the realistic, fully 3D transonic high-pressure turbine stage MT1 using Large-Eddy Simulations (LES). An analysis of the basic flow and the different turbine noise generation mechanisms is performed for two configurations: one with a steady inflow and a second with a pulsed inlet, where a plane entropy wave train at a given frequency is injected before propagating across the stage generating indirect noise. The noise is evaluated through the Dynamic Mode Decomposition of the flow field. It is compared with previous 2D simulations of a similar stator/rotor configuration, as well as with the compact theory of Cumpsty and Marble. Results show that the upstream propagating entropy noise is reduced due to the choked turbine nozzle guide vane. Downstream acoustic waves are found to be of similar strength to the 2D case, highlighting the potential impact of indirect combustion noise on the overall noise signature of the engine.

An Advanced Single-Stage Turbine Facility for Investigating Non-Axisymmetric Contoured Endwalls in the Presence of Purge Flow

2019 ◽  
Author(s):  
Robin R. Jones ◽  
Oliver J. Pountney ◽  
Bjorn L. Cleton ◽  
Liam E. Wood ◽  
B. Deneys J. Schreiner ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Static Pressure ◽  
Optical Measurement ◽  
Guide Vane ◽  
Single Stage ◽  
Test Facility ◽  
Pressure Distributions ◽  
Mainstream Flow ◽  
Purge Flow ◽  
Nozzle Guide

Abstract In modern gas turbines, endwall contouring (EWC) is employed to modify the static pressure field downstream of the vanes and minimise the growth of secondary flow structures developed in the blade passage. Purge flow (or egress) from the upstream rim-seal interferes with the mainstream flow, adding to the loss generated in the rotor. Despite this, EWC is typically designed without consideration of mainstream-egress interactions. The performance gains offered by EWC can be reduced, or in the limit eliminated, when purge air is considered. In addition, EWC can result in a reduction in sealing effectiveness across the rim seal. Consequently, industry is pursuing a combined design approach that encompasses the rim-seal, seal-clearance profile and EWC on the rotor endwall. This paper presents the design of, and preliminary results from a new single-stage axial turbine facility developed to investigate the fundamental fluid dynamics of egress-mainstream flow interactions. To the authors’ knowledge this is the only test facility in the world capable of investigating the interaction effects between cavity flows, rim seals and EWC. The design of optical measurement capabilities for future studies, employing volumetric velocimetry and planar laser induced fluorescence are also presented. The fluid-dynamically scaled rig operates at benign pressures and temperatures suited to these techniques and is modular. The facility enables expedient interchange of EWC (integrated into the rotor bling), blade-fillet and rim-seals geometries. The measurements presented in this paper include: gas concentration effectiveness and swirl measurements on the stator wall and in the wheel-space core; pressure distributions around the nozzle guide vanes at three different spanwise locations; pitchwise static pressure distributions downstream of the nozzle guide vane at four axial locations on the stator platform.

scholarly journals Turbulent Combustion Modelling and Experiments: Recent Trends and Developments

2019 ◽  
Vol 103 (4) ◽  
pp. 847-869 ◽  
Author(s):  
A. Giusti ◽  
E. Mastorakos
Keyword(s):  
Turbulent Combustion ◽  
Mixture Fraction ◽  
Moment Closure ◽  
Combustion Model ◽  
Complex Geometries ◽  
Conditional Moment ◽  
Practical Applications ◽  
Spray Flames ◽  
Reaction Zones ◽  
Soot Emissions

AbstractThe development of better laser-based experimental methods and the fast rise in computer power has created an unprecedented shift in turbulent combustion research. The range of species and quantities measured and the advent of kHz-level planar diagnostics are now providing great insights in important phenomena and applications such as local and global extinction, pollutants, and spray combustion that were hitherto unavailable. In simulations, the shift to LES allows better representation of the turbulent flow in complex geometries, but despite the fact that the grid size is smaller than in RANS, the push towards realistic conditions and the need to include more detailed chemistry that includes very fast species and thin reaction zones emphasize the necessity of a sub-grid turbulent combustion model. The paper discusses examples from current research with experiments and modelling that focus on flame transients (self-excited oscillations, local extinction), sprays, soot emissions, and on practical applications. These demonstrate how current models are being validated by experimental data and the concerted efforts the community is taking to promote the modelling tools to industry. In addition, the various coordinated International Workshops on non-premixed, premixed, and spray flames, and on soot are discussed and some of their target flames are explored. These comprise flames that are relatively simple to describe from a fluid mechanics perspective but contain difficult-to-model combustion problems such as extinction, pollutants and multi-mode reaction zones. Recently, swirl spray flames, which are more representative of industrial devices, have been added to the target flames. Typically, good agreement is found with LES and some combustion models such as the progress variable - mixture fraction flamelet model, the Conditional Moment Closure, and the Transported PDF method, but predicting soot emissions and the condition of complete extinction in complex geometries is still elusive.

NOx Emissions Reduction in an Innovative Industrial Gas Turbine Combustor (GE10 Machine): A Numerical Study of the Benefits of a New Pilot-System on Flame Structure and Emissions

2005 ◽  
Author(s):  
Antonio Andreini ◽  
Bruno Facchini ◽  
Luca Mangani ◽  
Antonio Asti ◽  
Gianni Ceccherini ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Numerical Study ◽  
Flame Structure ◽  
Combustion Model ◽  
Emissions Reduction ◽  
Minimal Amount ◽  
Nox Emissions ◽  
Ambient Temperatures ◽  
Wide Range

One of the driving requirements in gas turbine design is emissions reduction. In the mature markets (especially the North America), permits to install new gas turbines are granted provided emissions meet more and more restrictive requirements, in a wide range of ambient temperatures and loads. To meet such requirements, design techniques have to take advantage also of the most recent CFD tools. As a successful example of this, this paper reports the results of a reactive 3D numerical study of a single-can combustor for the GE10 machine, recently updated by GE-Energy. This work aims to evaluate the benefits on the flame shape and on NOx emissions of a new pilot-system located on the upper part of the liner. The former GE10 combustor is equipped with fuel-injecting-holes realizing purely diffusive pilot-flames. To reduce NOx emissions from the current 25 ppmvd@15%O2 to less than 15 ppmvd@15%O2 (in the ambient temperature range from −28.9°C to +37.8°C and in the load range from 50% and 100%), the new version of the combustor is equipped with 4 swirler-burners realizing lean-premixed pilot flames; these flames in turn are stabilized by a minimal amount of lean-diffusive sub-pilot-fuel. The overall goal of this new configuration is the reduction of the fraction of fuel burnt in diffusive flames, lowering peak temperatures and therefore NOx emissions. To analyse the new flame structure and to check the emissions reduction, a reactive RANS study was performed using STAR-CD™ package. A user-defined combustion model was used, while to estimate NOx emissions a specific scheme was also developed. Three different ambient temperatures (ISO, −28.9°C and 37.8°C) were simulated. Results were then compared with experimental measurements (taken both from the engine and from the rig), resulting in reasonable agreement. Finally, an additional simulation with an advanced combustion model, based on the laminar flamelet approach, was performed. The model is based on the G-Equation scheme but was modified to study partially premixed flames. A geometric procedure to solve G-Equation was implemented as add-on in STAR-CD™.

Aerodynamic Implications of Reduced Vane Count

2015 ◽  
Author(s):  
Ranjan Saha ◽  
Jens Fridh ◽  
Mats Annerfeldt
Keyword(s):  
Gas Turbines ◽  
Fossil Fuels ◽  
Positive Impact ◽  
Guide Vane ◽  
Suction Side ◽  
Combined Cycle ◽  
Significant Deficit ◽  
Nozzle Guide ◽  
The Cost ◽  
Cooling Air

Given the shortage of fossil fuels and the growing greenhouse effect, one strive in modern gas turbines is to make maximum usage of the burnt fuel. By reducing the number of vanes or blades and thereby increasing the loading per vane (or blade) it is possible to spend less cooling air, which will have a positive impact on the combined cycle efficiency. It also reduces the number of components and usage of metal and thereby also the cost of the engine. These savings should be achieved without any efficiency deficit in aerodynamic efficiency. Based on the fact, aerodynamic investigations were performed to see the aerodynamic implications of reduced vane number in a transonic annular sector cascade. The number of new nozzle guide vane was reduced with 24% compared to a previous design with higher vane count. The investigated vanes were two typical high pressure gas turbine vanes. Results regarding the loading indicated an expected increase with the reduced vane case. The minimum static pressure at the suction side is lower and at an earlier location for the reduced vane case and therefore, an extension of the trailing edge deceleration zone is observed for the reduced vane case. Results regarding losses indicate that even though the losses produced per vane significantly increases for the reduced vane case, a comparison of mass averaged losses between the reduced vane case and previous vane case show similar spanwise loss distributions. Assessing results leads to a conclusion that the reduction of the number of vanes in the first stage seems to be a useful method to save cooling flow as well as material costs without any significant deficit in overall efficiency.

Nozzle Guide Vane Static Strip Seals

2006 ◽  
Author(s):  
Arash Farahani ◽  
Peter Childs
Keyword(s):  
Gas Turbines ◽  
Guide Vane ◽  
Main Stream ◽  
Guide Vanes ◽  
Advantages And Disadvantages ◽  
Air System ◽  
Improved Performance ◽  
Nozzle Guide ◽  
Nozzle Guide Vanes ◽  
Assembly Constraints

Sealing of components where there is no relative motion between the elements concerned remains a significant challenge in many gas turbine engine applications. Loss of sealing and cooling air from the internal air system through seals impacts on specific fuel consumption and can lead to undesirable flow interactions with resultant cost implications. For gas turbines, various strip seal types have been developed for use between Nozzle Guide Vanes in order to limit the flow of gas between the main stream annulus and the internal air system. Many different types of design have been proposed for overcoming strip seal problems such as misalignment of the grooves due to manufacturing and assembly constraints. In this paper various methods, with a particular focus on patents, for minimising the amount of leakage caused by such problems for strip seals between nozzle guide vanes are reviewed. By considering the advantages and disadvantages of each technique it is concluded that although apparently new strip seal designs for NGVs have improved performance, none of them can be considered to be ideal. This paper reviews the techniques and makes recommendations for future designs.

Sign in / Sign up

Export Citation Format

Share Document