Experimental and Computational Investigation of Film Cooling Performance and External Flowfield Effects due to Impingement Coolant Feed in the Leading Edge of a Turbine Blade

2021 ◽  
Author(s):  
Jacob D. Moore ◽  
Christopher C. Easterby ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Leading Edge ◽  
Field Measurements ◽  
Suction Side ◽  
Computational Investigation ◽  
Exterior Surface ◽  
Cooling Performance ◽  
Root Cause ◽  
Shaped Hole ◽  
Adiabatic Effectiveness

Abstract The effects that leading-edge impingement coolant feeds have on the external flowfield and on film cooling performance in the showerhead have not been studied thoroughly in the literature. To isolate the influence of the impingement feed, experimental adiabatic effectiveness and off-the-wall thermal field measurements were made using a shaped hole geometry fed by an ideal plenum coolant feed and by an engine-realistic impingement coolant feed. The impingement configuration exhibited around 10% higher adiabatic effectiveness levels than the plenum configuration did — a finding in agreement with the few studies isolating this effect. CFD RANS simulations of the impingement and the pseudo-plenum configurations from a companion study were consulted to investigate the root cause of this difference in performance because the experimental data alone did not sufficiently explain it. In the impingement feed simulation, flow remained better attached throughout the hole (both at the inlet and at the diffuser) due to a rotation caused by the impingement flow, leading to better attachment on the exterior surface. This was most significant for the suction side holes at higher blowing ratios wherein the pseudo-plenum caused much more severe separation in the holes than the impingement configuration did.

Effects on Film Cooling Performance in the Showerhead From Geometric Parameterization of Shaped Hole Designs

2021 ◽  
Author(s):  
Jacob D. Moore ◽  
Christopher C. Easterby ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Thermal Protection ◽  
Leading Edge ◽  
Field Measurements ◽  
High Heat ◽  
Area Ratio ◽  
Cooling Performance ◽  
Shaped Hole ◽  
Adiabatic Effectiveness ◽  
Marginal Improvement

Abstract The high heat loads at the leading-edge regions of turbine vanes and blades necessitate the most robust thermal protection, typically accomplished via a dense array of film cooling holes, nicknamed the “showerhead.” Although research has shown that film cooling using shaped holes provides more reliable thermal protection than that using cylindrical holes, the effects on cooling performance from varying the geometric details of the shaped hole design are not well characterized. In this study, adiabatic effectiveness and off-the-wall thermal field measurements were conducted for two shaped hole geometries designed as successors to a baseline hole geometry presented in a previous study. One geometry with a 40% increase in area ratio exhibited only a marginal improvement in adiabatic effectiveness (∼10%). A second design with a 12° forward and lateral expansion angle with a breakout area 40% larger performed marginally worse than its matched area ratio counterpart (∼15% lower), suggesting a negative sensitivity to breakout area. Such changes in performance for different shaped hole designs were small compared to the boost in performance gained by switching from a cylindrical hole to a shaped hole, which suggests cooling performance is insensitive to specific shaped hole details provided the exterior coolant flow is well-attached.

scholarly journals Effects of Hole Shape on Film Cooling With Large Angle Injection

1999 ◽  
Author(s):  
Atui Kohil ◽  
David G. Bogard
Keyword(s):  
Velocity Field ◽  
Film Cooling ◽  
Field Measurements ◽  
Round Hole ◽  
Cooling Performance ◽  
Injection Angle ◽  
Hole Shape ◽  
Shaped Hole ◽  
Adiabatic Effectiveness ◽  
Better Than

In this study the film cooling performance of a single row of discrete holes inclined at an injection angle of 55° is investigated at a density ratio of DR = 1.6. Three different hole geometries were used in this study, a round hole and two shaped holes. One shaped hole had forward and lateral expansions of 15°, and the other a 15° lateral with a 25° forward expansion. For reference, a round hole with an injection angle of 35° was also tested. The film cooling performance of each hole shape was evaluated using adiabatic effectiveness, thermal field, and velocity field measurements. The shaped holes showed higher spatially averaged adiabatic effectiveness than the round hole over the whole range of momentum flux ratios (I) investigated. The effectiveness values for the shaped holes were only marginally better than the round hole at the low I, but at the high I, the shaped holes performed much better than the round hole. The temperature and velocity field measurements near the hole exit suggest that there is a slight detachment of the jet from the wall for the round hole, while the jets remain attached for the two shaped holes. The shaped hole with the larger forward expansion had a warmer jet with a higher trajectory at the hole exit suggesting ingestion of mainstream fluid and flow separation within the hole.

Scaling of Performance for Varying Density Ratio Coolants on an Airfoil With Strong Curvature and Pressure Gradient Effects

2000 ◽  
Author(s):  
Marcia I. Ethridge ◽  
J. Michael Cutbirth ◽  
David G. Bogard
Keyword(s):  
Pressure Gradient ◽  
Film Cooling ◽  
Density Ratio ◽  
Flux Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Cooling Performance ◽  
Injection Angle ◽  
Adiabatic Effectiveness ◽  
Strong Curvature

An experimental study was conducted to investigate the film cooling performance on the suction side of a first stage turbine vane. Tests were conducted on a nine times scale vane model at density ratios of DR = 1.1 and 1.6 over a range of blowing conditions, 0.2 ≤ M ≤ 1.5 and 0.05 ≤ I ≤ 1.2. Two different mainstream turbulence intensity levels, Tu∞ = 0.5% and 20%, were also investigated. The row of coolant holes studied was located in a position of both strong curvature and strong favorable pressure gradient. In addition, its performance was isolated by blocking the leading edge showerhead coolant holes. Adiabatic effectiveness measurements were made using an infrared camera to map the surface temperature distribution. The results indicate that film cooling performance was greatly enhanced over holes with a similar 50° injection angle on a flat plate. Overall, adiabatic effectiveness scaled with mass flux ratio for low blowing conditions and with momentum flux ratio for high blowing conditions. However, for M < 0.5 there was a higher rate of decay for the low density ratio data. High mainstream turbulence had little effect at low blowing ratios, but degraded performance at higher blowing ratios.

Scaling of Performance for Varying Density Ratio Coolants on an Airfoil With Strong Curvature and Pressure Gradient Effects

2000 ◽  
Vol 123 (2) ◽  
pp. 231-237 ◽  
Author(s):  
Marcia I. Ethridge ◽  
J. Michael Cutbirth ◽  
David G. Bogard
Keyword(s):  
Pressure Gradient ◽  
Film Cooling ◽  
Density Ratio ◽  
Flux Ratio ◽  
Leading Edge ◽  
Suction Side ◽  
Cooling Performance ◽  
Injection Angle ◽  
Adiabatic Effectiveness ◽  
Strong Curvature

An experimental study was conducted to investigate the film cooling performance on the suction side of a first-stage turbine vane. Tests were conducted on a nine times scale vane model at density ratios of DR=1.1 and 1.6 over a range of blowing conditions, 0.2⩽M⩽1.5 and 0.05⩽I⩽1.2. Two different mainstream turbulence intensity levels, Tu∞=0.5 and 20 percent, were also investigated. The row of coolant holes studied was located in a position of both strong curvature and strong favorable pressure gradient. In addition, its performance was isolated by blocking the leading edge showerhead coolant holes. Adiabatic effectiveness measurements were made using an infrared camera to map the surface temperature distribution. The results indicate that film cooling performance was greatly enhanced over holes with a similar 50 deg injection angle on a flat plate. Overall, adiabatic effectiveness scaled with mass flux ratio for low blowing conditions and with momentum flux ratio for high blowing conditions. However, for M<0.5, there was a higher rate of decay for the low density ratio data. High mainstream turbulence had little effect at low blowing ratios, but degraded performance at higher blowing ratios.

Evaluation of Superposition Predictions for Showerhead Film Cooling on a Vane

2014 ◽  
Author(s):  
Joshua B. Anderson ◽  
James R. Winka ◽  
David G. Bogard ◽  
Michael E. Crawford
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Leading Edge ◽  
Suction Side ◽  
Pressure Side ◽  
Edge Region ◽  
Current Investigation ◽  
Engine Design ◽  
Turbine Vane ◽  
Adiabatic Effectiveness

The leading edge of a turbine vane is subject to some of the highest temperature loading within an engine, and an accurate understanding of leading edge film coolant behavior is essential for modern engine design. Although there have been many investigations of the adiabatic effectiveness for showerhead film cooling of a vane leading edge region, there have been no previous studies in which individual rows of the showerhead were tested with the explicit intent of validating superposition models. For the current investigation, a series of adiabatic effectiveness experiments were performed with a five-row and three-row showerhead. The experiments were repeated separately with each individual row of holes active. This allowed evaluation of superposition methods on both the suction side of the vane, which was moderately convex, and the pressure side of the vane, which was mildly concave. Superposition was found to accurately predict performance on the suction side of the vane at lower momentum flux ratios, but not at higher momentum flux ratios. On the pressure side of the vane the superposition predictions were consistently lower than measured values, with significant errors occurring at the higher momentum flux ratios. Reasons for the under-prediction by superposition analysis are presented.

High-Resolution Film Cooling Effectiveness Measurements of Axial Holes Embedded in a Transverse Trench With Various Trench Configurations

2006 ◽  
Vol 129 (2) ◽  
pp. 294-302 ◽  
Author(s):  
Scot K. Waye ◽  
David G. Bogard
Keyword(s):  
High Resolution ◽  
Film Cooling ◽  
Density Ratio ◽  
Field Measurements ◽  
Suction Side ◽  
Lateral Spreading ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Flow Parameters ◽  
Adiabatic Effectiveness

Adiabatic film cooling effectiveness of axial holes embedded within a transverse trench on the suction side of a turbine vane was investigated. High-resolution two-dimensional data obtained from infrared thermography and corrected for local conduction provided spatial adiabatic effectiveness data. Flow parameters of blowing ratio, density ratio, and turbulence intensity were independently varied. In addition to a baseline geometry, nine trench configurations were tested, all with a depth of 1∕2 hole diameter, with varying widths, and with perpendicular and inclined trench walls. A perpendicular trench wall at the very downstream edge of the coolant hole was found to be the key trench characteristic that yielded much improved adiabatic effectiveness performance. This configuration increased adiabatic effectiveness up to 100% near the hole and 40% downstream. All other trench configurations had little effect on the adiabatic effectiveness. Thermal field measurements confirmed that the improved adiabatic effectiveness that occurred for a narrow trench with perpendicular walls was due to a lateral spreading of the coolant and reduced coolant jet separation. The cooling levels exhibited by these particular geometries are comparable to shaped holes, but much easier and cheaper to manufacture.

Effects of Hot Streaks on Adiabatic Effectiveness for a Film Cooled Turbine Vane

2004 ◽  
Author(s):  
Krishnakumar Varadarajan ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Field Measurements ◽  
Suction Side ◽  
Experimental Program ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Vane ◽  
Adiabatic Effectiveness ◽  
Hot Streak ◽  
Effectiveness Data

Turbine guide vanes in gas turbine engines are typically subjected to localized “hot streaks” emanating from the combustor. This experimental program examined how these hot streaks affect the film cooling performance for these vanes. Adiabatic effectiveness tests were conducted on the showerhead and suction side regions of the vane. Particular attention was placed on how to scale that adiabatic effectiveness data obtained with a hot streak to correctly predict the adiabatic effectiveness. Thermal field measurements were made to determine the temperature gradients for the hot streak near the wall. These experiments showed that the effect of the hot streak on the adiabatic effectiveness could be accounted for by using an “adjusted” mainstream temperature equal to the hot streak temperature at the wall of the vane.

ADIABATIC EFFECTIVENESS AND THERMAL FIELD MEASUREMENTS OF A SHAPED HOLE IN THE SHOWERHEAD OF A MODEL TURBINE BLADE

2021 ◽  
pp. 1-37
Author(s):  
Jacob D. Moore ◽  
Matthew Horner ◽  
David G. Bogard
Keyword(s):  
Turbine Blade ◽  
Thermal Field ◽  
Leading Edge ◽  
Field Measurements ◽  
Injection Rate ◽  
Edge Region ◽  
Test Environment ◽  
Coolant Injection ◽  
Shaped Hole ◽  
Adiabatic Effectiveness

Abstract Few published studies incorporating shaped hole designs in the leading-edge region, or showerhead, of turbine airfoils have been performed; but among them is the indication that shaped holes may offer an improvement in coolant performance compared to cylindrical holes. A shaped hole was designed with the goal of high performance in the showerhead. The performance and physical behavior of this shaped hole design was studied in comparison to a traditional cylindrical hole design in a series of experiments. The geometries were built into the leading edge of a scaled-up turbine blade model for testing in a low-speed simulated linear cascade. To accomplish an engine-representative test environment, a nominally 5% approach turbulence level was used for this study. Adiabatic effectiveness as a function of coolant injection rate was measured for the two designs using infrared thermography. In addition, off-the-wall thermal field measurements were performed for each hole geometry in the leading-edge region. It was found that the shaped hole offered ~20-100% higher performance in terms of adiabatic effectiveness depending on the coolant injection rate. The thermal field measurements suggested that this was due to the better attachment of the jets exiting the shaped holes, the momenta of which were effectively reduced by the diffusers.

Theoretical Film Cooling Performance of Multi Trench Configurations on Flat Plate

2013 ◽  
Author(s):  
Antar M. M. Abdala ◽  
Qun Zheng ◽  
Fifi N. M. Elwekeel
Keyword(s):  
Film Cooling ◽  
Additional Benefit ◽  
The Other ◽  
Low Flow ◽  
Computational Simulations ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Ansys Cfx ◽  
Shaped Hole ◽  
Adiabatic Effectiveness

In the present work, computational simulations was made using ANSYS CFX to predict the improvements in film cooling performance with multi trench. Multi-trench configuration consists of two trenches together, one wider trench and the other is narrow trench that extruded from the wider one. Several blowing ratios in the range (0.5:5) were investigated. By using the multi trench configuration, the coolant jet impacted the trench wall two times allowing increasing the spreading of coolant laterally in the trench, reducing jet velocity and jet completely covered on the surface. The results indicate that this configuration increased adiabatic effectiveness as blowing ratio increased. No observed film blow-off at all blowing ratios. The adiabatic film effectiveness of multi trench case outperformed the narrow trench case, laidback fan-shaped hole, fan-shaped hole and cylinder hole at different blowing ratios. An additional benefit is the low flow rate will provide the same cooling effect by using multi trench configuration.

Rotating Film Cooling Performance of the Hole Near the Leading Edge on the Suction Side of the Turbine Blade

2018 ◽  
Author(s):  
Zhi-yu Zhou ◽  
Hai-wang Li ◽  
Hai-chao Wang ◽  
Guo-qin Zhao ◽  
Feng Han ◽  
...  
Keyword(s):  
Film Cooling ◽  
Leading Edge ◽  
Suction Side ◽  
Axial Direction ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Rotating Speed ◽  
Blowing Ratio ◽  
Numerical Studies

This paper reports the experimental and numerical studies on the effects of rotating speed and blowing ratio on the film cooling performance of the hole near the leading edge on the suction side of the turbine blade. The chord and height of the blade are 60mm and 80mm respectively. The film hole with diameter of 0.8mm is located in the mid span on the suction side at axial location of 8%. The injection angle of the hole is 45° to the suction surface of the blade and is nearly perpendicular to the axial direction. Both experimental and numerical studies were carried out with rotating speeds of 300rpm, 450rpm and 600rpm, and with blowing ratios of 0.5, 1.0, 1.5 and 2.0. CO2 was used as the coolant. Experimental data was measured by applying the Thermochromic Liquid Crystal (TLC) technique and the Stroboscopic Imaging Technique. Mainstream and coolant were heated to 308K and 318K respectively. Numerical studies were performed to assist the analysis of the experimental results. The SST turbulence model was applied in the simulations. Results show that the film cooling performance of the hole near the leading edge is different from that of the hole further downstream on the suction side. This is because the direction of the jet is nearly perpendicular to the axial direction, which increases the effect of the Coriolis force. Besides, the mainstream from leading edge also has effects on film cooling performance. With the increase of the blowing ratio, the film coverage area and spatially averaged film cooling effectiveness increase first and then decrease. The maximum film coverage and averaged film cooling effectiveness appear at blowing ratio of 1.0 and rotating speed of 300rpm. Moreover, the upward deflection angle of the film trajectory increases slightly with the increase of the blowing ratio. Higher rotating speed intensifies the deflection of the film trajectory. Therefore, the film coverage and the averaged film cooling effectiveness decrease rapidly.

Sign in / Sign up

Export Citation Format

Share Document