Durability Testing of Biomass Based Oxygenated Fuel Components in a Compression Ignition Engine

2017 ◽  
Author(s):  
Marc E. Baumgardner ◽  
Arunachalam Lakshminarayanan ◽  
Daniel B. Olsen ◽  
Matthew A. Ratcliff ◽  
Robert L. McCormick ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Engine Performance ◽  
Engine Oil ◽  
Long Term Effects ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Minimal Impact ◽  
Carbon Buildup ◽  
The Impact

Blending cellulosic biofuels with traditional petroleum-derived fuels results in transportation fuels with reduced carbon footprints. Many cellulosic fuels rely on processing methods that produce mixtures of oxygenates which must be upgraded before blending with traditional fuels. Complete oxygenate removal is energy-intensive and it is likely that such biofuel blends will necessarily contain some oxygen content to be economically viable. Previous work by our group indicated that diesel fuel blends with low levels (<4%-vol) of oxygenates resulted in minimal negative effects on short-term engine performance and emissions. However, little is known about the long-term effects of these compounds on engine durability issues such as the impact on fuel injection, in-cylinder carbon buildup, and engine oil degradation. In this study, four of the oxygenated components previously tested were blended at 4%-vol in diesel fuel and tested with a durability protocol devised for this work consisting of 200 hrs of testing in a stationary, single-cylinder, Yanmar diesel engine operating at constant load. Oil samples, injector spray patterns, and carbon buildup from the injector and cylinder surfaces were analyzed. It was found that, at the levels tested, these fuels had minimal impact on the overall engine operation, which is consistent with our previous findings.

Field Test of a Cooper LSVB-20GDT Engine Operating on Biodiesel

2009 ◽  
Author(s):  
Greg Beshouri ◽  
Henry Lam
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Engine Performance ◽  
Engine Emissions ◽  
Single Cylinder ◽  
Energy Center ◽  
The Difference ◽  
Engine Testing ◽  
The Impact ◽  
Diesel Operation

NRG Energy Center Paxton LLC (NRG-ECP) operates two Cooper LSVB-20GDT gas-diesel engines at a combined heat and power facility in Harrisburg, PA. NRG-ECP commissioned Advanced Engine Technologies Corporation (AETC) to conduct a literature review on the impacts of operating these engines on Biodiesel. Based on the somewhat favorable results of the review, NRG-ECP with support from AETC performed single cylinder and then full engine testing on one engine to assess the impact of Biodiesel operation on engine performance, emissions and operability as an alternative to full diesel operation. The results showed the engine exhibited no major differences in combustion performance or engine operability when running on Biodiesel in comparison to standard diesel fuel. During single cylinder testing the switch between diesel and Biodiesel was virtually undetectable. In the full engine Biodiesel test the unit started, idled, synchronized and loaded identical to diesel fuel. From a combustion perspective, the differences in Biodiesel vs. diesel operation are primarily attributable to the difference in air/fuel ratio due to the different fuel compositions. Fuel injection performance did not appear to change significantly or impact engine emissions.

Diesel Engine Operation Using Ammonia as a Carbon-Free Fuel

2010 ◽  
Author(s):  
Aaron J. Reiter ◽  
Song-Charng Kong
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Fuel Mixture ◽  
Maximum Energy ◽  
Nox Emissions ◽  
Compression Ignition Engine ◽  
Relief Valve ◽  
Engine Operation ◽  
Engine Torque ◽  
Energy Replacement

Ammonia combustion does not produce carbon dioxide and thus can be regarded as a carbon-free fuel. Ammonia was used as a fuel in a compression-ignition engine in this study. Vapor ammonia was introduced into the engine intake port, and diesel fuel was injected directly into the cylinder to initiate combustion. This dual-fuel approach was chosen because ammonia has a high resistance to autoignition. A liquid ammonia tank was used for fuel storage and a high pressure relief valve regulated the ammonia flow rate, and ignition was controlled by diesel fuel injection. Ammonia was used as an energy replacement for diesel fuel. The results showed that the peak engine torque could be achieved by using different combinations of diesel fuel and ammonia. During testing, a maximum energy replacement of 95% was measured. It should be noted that, if more ammonia is added, a higher than rated power can be achieved depending on engine load conditions. It was also shown that CO2 emissions were reduced monotonically for the same engine torque output as the amount of the ammonia in the fuel mixture increased. Additionally, burning ammonia in engines does not necessarily increase NOx emissions despite the fuel-bound nitrogen. Lower levels of NOx emissions were obtained as long as energy substitution by ammonia did not exceed 60%. This is thought to occur because of the lower combustion temperature of ammonia.

Measurement of cycle-resolved engine-out soot concentration from a diesel-pilot assisted natural gas direct-injection compression-ignition engine

2021 ◽  
pp. 146808742098626
Author(s):  
Pooyan Kheirkhah ◽  
Patrick Kirchen ◽  
Steven Rogak
Keyword(s):  
Response Time ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Exhaust System ◽  
Cycle Period ◽  
Scanning Mobility Particle Sizer ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Exhaust Port ◽  
Exhaust Stream

Exhaust-stream particulate matter (PM) emission from combustion sources such as internal combustion engines are typically characterized with modest temporal resolutions; however, in-cylinder investigations have demonstrated significant variability and the importance of individual cycles in transient PM emissions. Here, using a Fast Exhaust Nephelometer (FEN), a methodology is developed for measuring the cycle-specific PM concentration at the exhaust port of a single-cylinder research engine. The measured FEN light-scattering is converted to cycle-resolved soot mass concentration ([Formula: see text]), and used to characterize the variability of engine-out soot emission. To validate this method, exhaust-port FEN measurements are compared with diluted gravimetric PM mass and scanning mobility particle sizer (SMPS) measurements, resulting in close agreements with an overall root-mean-square deviation of better than 30%. It is noted that when PM is sampled downstream in the exhaust system, the particles are larger by 50–70 nm due to coagulation. The response time of the FEN was characterized using a “skip-firing” scheme, by enabling and disabling the fuel injection during otherwise steady-state operation. The average response time due to sample transfer and mixing times is 55 ms, well below the engine cycle period (100 ms) for the considered engine speeds, thus suitable for single-cycle measurements carried out in this work. Utilizing the fast-response capability of the FEN, it is observed that cycle-specific gross indicated mean effective pressure (GIMEP) and [Formula: see text] are negatively correlated ([Formula: see text]: 0.2–0.7), implying that cycles with lower GIMEP emit more soot. The physical causes of this association deserve further investigation, but are expected to be caused by local fuel-air mixing effects. The averaged exhaust-port [Formula: see text] is similar to the diluted gravimetric measurements, but the cycle-to-cycle variations can only be detected with the FEN. The methodology developed here will be used in future investigations to characterize PM emissions during transient engine operation, and to enable exhaust-stream PM measurements for optical engine experiments.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

scholarly journals Thermodynamic cycles variability of TJI gas engine with different mixture preparation systems

2020 ◽  
Vol 181 (2) ◽  
pp. 46-52
Author(s):  
Filip SZWAJCA ◽  
Krzysztof WISŁOCKI
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Engine Operation ◽  
Gas Engine ◽  
Part Load ◽  
Mixture Preparation ◽  
Key Factor ◽  
Test Engine ◽  
Operation Stability ◽  
The Impact

Gas engines are a viable source of propulsion due to the ecological indicators of gas fuels and the large amount of the needed natural resources. Combustion of lean homogeneous gas mixtures allows achieving higher thermal efficiency values, which is a key factor in current engine development trends. Using the spark-jet ignition system (also called as Turbulent Jet Ignition or Two-stage combustion) significantly improves the efficiency and stability of the combustion process, especially in the part-load operation on lean or very lean mixtures. This paper presents the impact of using two different fuel injection methods: Port Fuel Injection or Mixer on the operation stability of a gas engine designed for LDVs. Comparative studies of two different mixture preparation systems were carried out on a single-cylinder AVL 5804 test engine. By re-cording the cylinder pressure for a significant number of engine cycles, it became possible to determine the repeatability of engine operation and to correlate the results with the mixture formation system and the air-fuel ratio. In the performed research the beneficial effect of the mixer system application on the engine operation stability in the part-load conditions was found.

Predicted Qualitative Effects of Alternate Liquid Fuels on Heavy-Duty Compression-Ignition Engines

2009 ◽  
Author(s):  
Gong Chen
Keyword(s):  
Fuel Injection ◽  
Cetane Number ◽  
Fuel Properties ◽  
Liquid Fuels ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
End Effects ◽  
Compression Ignition Engines ◽  
The Impact

It is always desirable for a heavy-duty compression-ignition engine, such as a diesel engine, to possess a capability of using alternate liquid fuels without significant hardware modification to the engine baseline. Because fuel properties vary between various types of liquid fuels, it is important to understand the impact and effects of the fuel properties on engine operating and output parameters. This paper intends and attempts to achieve that understanding and to predict the qualitative effects by studying analytically and qualitatively how a heavy-duty compression-ignition engine would respond to the variation of fuel properties. The fuel properties considered in this paper mainly include the fuel density, compressibility, heating value, viscosity, cetane number, and distillation temperature range. The qualitative direct and end effects of the fuel properties on engine bulk fuel injection, in-cylinder combustion, and outputs are analyzed and predicted. Understanding these effects can be useful in analyzing and designing a compression-ignition engine for using alternate liquid fuels.

scholarly journals Comparative Analysis of Combustion Stability of Diesel/Ethanol Utilization by Blend and Dual Fuel

Processes ◽  
2019 ◽  
Vol 7 (12) ◽  
pp. 946 ◽  
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Combustion Process ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Compression Ignition Engine ◽  
Energy Fraction ◽  
Pure Ethanol ◽  
Advantages And Disadvantages

The aim of the work is a comparison of two combustion systems of fuels with different reactivity. The first is combustion of the fuel mixture and the second is combustion in a dual-fuel engine. Diesel fuel was burned with pure ethanol. Both methods of co-firing fuels have both advantages and disadvantages. Attention was paid to the combustion stability aspect determined by COVIMEP as well as the probability density function of IMEP. It was analyzed also the spread of the maximum pressure value, the angle of the position of maximum pressure. The influence of ethanol on ignition delay time spread and end of combustion process was evaluated. The experimental investigation was conducted on 1-cylinder air cooled compression ignition engine. The test engine operated with constant rpm equal to 1500 rpm and constant angle of start of diesel fuel injection. The engine was operated with ethanol up to 50% of its energy fraction.

scholarly journals Research on combustion process of gasoline homogenous charge compression ignition engine

2018 ◽  
Vol 184 ◽  
pp. 01013
Author(s):  
Corneliu Cofaru ◽  
Mihaela Virginia Popescu
Keyword(s):  
Experimental Research ◽  
Fuel Injection ◽  
Combustion Process ◽  
Fuel Mixture ◽  
Spark Ignition Engine ◽  
Injection System ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Homogenous Charge Compression Ignition

The paper presents the research designed to develop a HCCI (Homogenous Charge Compression Ignition) engine starting from a spark ignition engine platform. The chosen test engine was a single cylinder, four strokes provided with a carburettor. The results of experimental research data obtained on this version were used as a baseline for the next phase of the research. In order to obtain the HCCI configuration, the engine was modified, as follows: the compression ratio was increased from 9.7 to 11.5 to ensure that the air – fuel mixture auto-ignite and to improve the engine efficiency; the carburettor was replaced by a direct fuel injection system in order to control precisely the fuel mass per cycle taking into account the measured intake air-mass; the valves shape were modified to provide a safety engine operation by ensuring the provision of sufficient clearance beetween the valve and the piston; the exchange gas system was changed from fixed timing to variable valve timing to have the possibilities of modification of quantities of trapped burnt gases. The cylinder processes were simulated on virtual model. The experimental research works were focused on determining the parameters which control the combustion timing of HCCI engine to obtain the best energetic and ecologic parameters.

Sign in / Sign up

Export Citation Format

Share Document