Experimental and Theoretical Optimization of Combustion Chamber and Fuel Distribution for the Low Emission DI Diesel Engine

2001 ◽  
Author(s):  
Yoshiyuki Kidoguchi ◽  
Michiko Sanda ◽  
Kei Miwa
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Combustion Chamber ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Process ◽  
Mixture Distribution ◽  
Initial Mixture ◽  
Injection Timing ◽  
Initial Heat

Abstract This study investigated the effect of combustion chamber geometry and initial mixture distribution on combustion process in a direct-injection diesel engine by means of experiment and CFD calculation. The high squish combustion chamber with squish lip could produce simultaneous reduction of NOx and particulate emissions with retarded injection timing in the real engine experiment. According to the CFD computation, the high squish combustion chamber with central pip is effective to continue combustion under the squish lip until the end of combustion and the combustion region forms rich and high turbulence atmosphere, which reduces NOx emissions. This chamber can also reduce initial burning because combustion continues under the squish lip. The CFD computation is also carried out in order to investigate the effect of initial mixture distribution on combustion process. The results suggest that mixture distribution affects the history of heat release rate. When fuel is distributed in the bottom or wide region in the combustion chamber, burned gas tends to spread to the cavity center and initial heat release rate becomes high. On the contrary, the high squish combustion chamber with central pip produces lower initial heat release rate because combustion with local rich condition continues long under the squish lip. Diffusion burning is promoted by high swirl motion in this chamber with keeping lower initial heat release rate.

Experimental and Theoretical Optimization of Combustion Chamber and Fuel Distribution for the Low Emission Direct-Injection Diesel Engine

2002 ◽  
Vol 125 (1) ◽  
pp. 351-357 ◽  
Author(s):  
Y. Kidoguchi ◽  
M. Sanda ◽  
K. Miwa
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Combustion Process ◽  
Mixture Distribution ◽  
Initial Mixture ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Particulate Emission ◽  
Direct Injection Diesel Engine

Effects of combustion chamber geometry and initial mixture distribution on the combustion process were investigated in a direct-injection diesel engine. In the engine experiment, a high squish combustion chamber with a squish lip could reduce both NOx and particulate emissions with retarded injection timing. According to the results of CFD computation and phenomenological modeling, the high squish combustion chamber with a central pip is effective to keep the combusting mixture under the squish lip until the end of combustion and the combustion region forms rich and highly turbulent atmosphere. This kind of mixture distribution tends to reduce initial burning, resulting in restraint of NOx emission while keeping low particulate emission.

Determination of the Start and End of Combustion in a Direct Injection Diesel Engine Using the Apparent Heat Release Rate

2017 ◽  
Author(s):  
Joseph Gerard T. Reyes ◽  
Edwin N. Quiros
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Direct Injection ◽  
Injection Timing ◽  
Fuel Injector ◽  
Direct Injection Diesel Engine ◽  
Crank Angle ◽  
Start Of Combustion

The combustion duration in an internal combustion engine is the period bounded by the engine crank angles known as the start of combustion (SOC) and end of combustion (EOC), respectively. This period is essential in analysis of combustion for the such as the production of exhaust emissions. For compression-ignition engines, such as diesel engines, several approaches were developed in order to approximate the crank angle for the start of combustion. These approaches utilized the curves of measured in-cylinder pressures and determining by inspection the crank angle where the slope is steep following a minimum value, indicating that combustion has begun. These pressure data may also be utilized together with the corresponding cylinder volumes to generate the apparent heat release rate (AHRR), which shows the trend of heat transfer of the gases enclosed in the engine cylinder. The start of combustion is then determined at the point where the value of the AHRR is minimum and followed by a rapid increase in value, whereas the EOC is at the crank angle where the AHRR attains a flat slope prior to the exhaust stroke of the engine. To verify the location of the SOC, injection line pressures and fuel injection timing are also used. This method was applied in an engine test bench using a four-cylinder common-rail direct injection diesel engine with a pressure transducer installed in the first cylinder. Injector line pressures and fuel injector voltage signals per engine cycle were also recorded and plotted. By analyzing the trends of this curves in line with the generated AHRR curves, the SOC may be readily determined.

Influence of the Spatial and Temporal Interaction Between Diesel Pilot and Directly Injected Natural Gas Jet on Ignition and Combustion Characteristics

2017 ◽  
Author(s):  
Georg Fink ◽  
Michael Jud ◽  
Thomas Sattelmayer
Keyword(s):  
Natural Gas ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Process ◽  
Gas Jet ◽  
Injection Timing ◽  
Release Rates ◽  
Temporal Interaction ◽  
The Impact

In this paper, pilot-ignited high pressure dual-fuel (HPDF) combustion of a natural gas jet is investigated on a fundamental basis by applying two separate single-hole injectors to a rapid compression expansion machine (RCEM). A Shadowgraphy system is used for optical observations, and the combustion progress is assessed in terms of heat release rates. The experiments focus on the combined influence of injection timing and geometrical jet arrangement on the jet interaction and the impact on the combustion process. In a first step, the operational range for successful pilot self-ignition and transition to natural gas jet combustion is determined, and the restricting phenomena are identified by analyzing the shadowgraph images. Within this range, the combustion process is assessed by evaluation of ignition delays and heat release rates. Strong interaction is found to delay or even prohibit pilot ignition, while it facilitates a fast and stable onset of the gas jet combustion. Furthermore, it is shown that the heat release rate is governed by the time of ignition with respect to the start of natural gas injection — as this parameter defines the level of premixing. Evaluation of the time of gas jet ignition within the operability map can therefore directly link a certain spatial and temporal interaction to the resulting heat release characteristics. It is finally shown that controlling the heat release rate through injection timing variation is limited for a certain angle between the two jets.

scholarly journals Analysis on Pattern of Heat Release Rate in Two-Stroke Slow Speed Diesel Engine (2nd Report: Prediction of the Combustion Process)

2003 ◽  
Vol 38 (5) ◽  
pp. 303-308
Author(s):  
Takeshi Imahashi ◽  
Eiji Tomita ◽  
Sadami Yoshiyama ◽  
Kouji Moriyama
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Process ◽  
Slow Speed

Prediction of the effect of injection parameters on NOx emission and burning quality in the direct injection diesel engine using a modified multizone model

1998 ◽  
Vol 212 (5) ◽  
pp. 427-436 ◽  
Author(s):  
H Salem ◽  
S. H. El-Bahnasy ◽  
M Elbaz
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Combustion Process ◽  
Injection Pressure ◽  
Cylinder Pressure ◽  
Injection Parameters ◽  
Multizone Model ◽  
Engine Power

Combustion process in a quiescent chamber diesel engine is modelled using a multizone model. This model divides the cylinder charge into two zones, namely the unburnt zone (surrounding air) and the burnt zone (fuel spray with entrained air). The burnt zone is subdivided into 16 concentric sprays, instead of only eight sprays as in previous work, each one with its own temperature and composition. Liquid fuel, fuel vapour, air and products of combustion are assumed to be present in each zone. Real gas relations are used to calculate the properties of the mixture while products of combustion are assumed to be in chemical equilibrium at local temperature. The extended Zeldovich mechanism is used to predict the NO x formation. The cylinder pressure, temperature, heat release rate, NO x rate and concentration are calculated. For different injection pressures, injection advance angles and different fuel orifice hole diameters, the results show that the model can predict the measured cylinder pressure with high accuracy but it predicts the measured heat release rate and NO x emission rate with moderate accuracy. In addition, the effect of injection parameters on the NO x emission and engine power is predicted and it has been shown that NO x emission can be reduced without noticeable loss of engine power. This can be done by appropriate choice of injection pressure, injection advance angle and fuel nozzle hole diameters.

Study of Pilot Injection for the Improvement of Combustion and Emissions Characteristics in a Heavy-Duty Diesel Engine

2014 ◽  
Vol 651-653 ◽  
pp. 866-874 ◽  
Author(s):  
Liang Chen ◽  
Hong Zeng ◽  
Xiao Bei Cheng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Injection Timing ◽  
Pilot Injection ◽  
Heavy Duty ◽  
Heavy Duty Diesel Engine ◽  
Heavy Duty Diesel ◽  
Injection Strategies

A 6-cylinder, turbocharged, common rail heavy-duty diesel engine was used in this study. The effect of pilot injection strategies on diesel fuel combustion process, heat release rate, emission and economy of diesel engine is studied. The pilot injection strategies include pilot injection timing and pilot injection mass to achieve the homogeneous compression ignition and lower temperature combustion of diesel engine. The two-color method was applied to take the flame images in the engine cylinder and obtain soot concentration distribution. The results demonstrate that with the advance of pilot injection timing, the peak in-cylinder pressure becomes lower, the ignition delay of the main combustion is shortened, the NOXand soot emissions are reduced, but the HC and CO emissions are increased. With the increase of pilot injection fuel mass, the heat release rate of the pilot injection combustion and the maximum rate of pressure rise increase, NOXand HC emissions are higher, and PM and CO emissions are reduced. The pilot combustion flame is non-luminous.

scholarly journals Combustion and Performance Study of Low-Displacement Compression Ignition Engines Operating with Diesel–Biodiesel Blends

2020 ◽  
Vol 10 (3) ◽  
pp. 907 ◽  
Author(s):  
Guillermo Valencia Ochoa ◽  
Carlos Acevedo Peñaloza ◽  
Jorge Duarte Forero
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Palm Oil ◽  
Heat Release Rate ◽  
Release Rate ◽  
Sunflower Oil ◽  
Combustion Process ◽  
Cylinder Pressure ◽  
Emission Analysis ◽  
Biodiesel Blends

This study investigated the influence of different biodiesel blends produced from residual sunflower oil and palm oil from agroindustry liquid waste on the characteristics of the combustion process, performance, and emissions in a single-cylinder diesel engine. For the analysis of the combustion process, a diagnostic model was developed based on the cylinder pressure signal, which allows the calculation of the heat release rate, the accumulated heat rate, and the temperature in the combustion chamber. This is to assess the influence of these parameters on engine emissions. The experiments on the diesel engine were carried out using five types of fuel: conventional diesel, two biodiesel blends of residual palm oil (PB5 and PB10), and two biodiesel blends formed with palm oil and sunflower oil residues (PB5SB5 and PB10SB5). The engine was running in four different modes, which covered its entire operating area. Experimental results show that the in-cylinder pressure curves decrease as the percentage of biodiesel in the fuel increases. Similarly, the results showed a decrease in the heat release rate for biodiesel blends. The diagrams of the accumulated heat release curves were larger for fuels with higher biodiesel content. This effect is reflected in the thermal efficiency of biodiesel blends since the maximum thermal efficiencies were 29.4%, 30%, 30.6%, 31.2%, and 31.8% for PB10SB5, PB5SB5, PB10, PB5, and diesel, respectively. The emission analysis showed that the blends of biodiesel PB5SB5 and PB10SB allowed a greater reduction in the emissions of CO, CO2, HC, and opacity of smoke in all the modes of operation tested, in comparison with the blends of biodiesel PB5 and PB10. However, NOx emissions increased. In general, biodiesel with the percentage of residual sunflower oil does not cause a significant change in the combustion process and engine performance, when compared to biodiesel that includes only residual palm oil.

Combustion and Emission Characteristics of Dual Fuel Engine for Different Parameters

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Jianjun Zhu ◽  
Peng Li ◽  
Yufeng Xie ◽  
Xin Geng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Cylinder Pressure ◽  
Fuel Delivery ◽  
Soot Emissions

The effects of compression ratio and fuel delivery advance angle on the combustion and emission characteristics of premixed methanol charge induced ignition by Fischer Tropsch diesel engine were investigated using a CY25TQ diesel engine. In the process of reducing the compression ratio from 16.9 to 15.4, the starting point of combustion is fluctuating, the peak of in-cylinder pressure and the maximum pressure increase rate decrease by 44.5% and 37.7% respectively. The peak instantaneous heat release rate increases by 54.4%. HC and CO emissions are on a rising trend. NOx and soot emissions were greatly decreased. The soot emission has the biggest drop of 50%. Reducing the fuel delivery advance angle will make the peak of in-cylinder pressure and the peak of pressure rise rate increase while the peak of heat release rate decreases. The soot emission is negatively correlated with the fuel delivery advance angle. When the fuel delivery advance angle is 16° CA, the soot emissions increased the most by 130%.

Sign in / Sign up

Export Citation Format

Share Document