Experimental Study of Injection and Combustion in a Diesel Engine for Heavy Quadricycle Use

2012 ◽  
Author(s):  
Ezio Mancaruso ◽  
Bianca M. Vaglieco ◽  
Luigi Allocca ◽  
Alessandro Montanaro ◽  
Luigi Arnone
Keyword(s):  
Soot Formation ◽  
Injection System ◽  
Spatial Density ◽  
Experimental Investigations ◽  
Maximum Pressure ◽  
Common Rail Injection System ◽  
The Third ◽  
Common Rail Injection ◽  
Density Analysis ◽  
Injection Strategies

An experimental investigation has been carried out on a diesel 1000 cc, two-valve, three-cylinder, engine for heavy quadricycle and off-road applications. The engine was equipped with a unit-pump common rail injection system, automotive derived, with maximum pressure 140 MPa and ECU able to manage multinjection strategies in Euro 4 target for the foreseen applications. Experimental investigations on the fuel spray have been carried out in an optically accessible vessel at engine gas density. Spatial and temporal spray behavior has been studied by image processing of the evolving jet pictures. Spray tip penetrations, cone angles and fuel spatial density analysis have been extracted and correlated to the injection and engine parameters. On the other side, visible flame propagation and soot formation process have been evaluated by digital imaging at high spatial and temporal resolution using a quartz window of the third cylinder obtained modifying the engine head. Strategies consisting of two injections per cycle, pilot and main, and typical of real engine working conditions have been investigated in the pressure range 43–116 MPa both in terms of injection rates and injected fuel dispersion. The effects of different injection strategies on soot formation and exhaust emissions have been evaluated.

scholarly journals Simulation and experimental coupled research of rate of heat release in DI diesel engine for various injection strategies

2008 ◽  
Vol 132 (1) ◽  
pp. 17-24
Author(s):  
Kazimierz LEJDA ◽  
Paweł WOŚ
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Direct Injection ◽  
Injection System ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
Release Analysis ◽  
Di Diesel Engine ◽  
Rate Of Heat Release ◽  
Injection Strategies

In the paper the rate of heat release analysis in direct injection diesel engine has been presented and discussed. The research has been carried out for two different injection strategies, i.e. for conventional single-phase injection and for triple-phase injection executed by a Common Rail injection system. The calculation methodology of heat release rate based on indicator diagram has been presented as well.

scholarly journals Analysis of the uniqueness of the combustion process of the Perkins 1104D-E44TA engine in dual-fuel operation powered by natural gas and diesel fuel

2019 ◽  
Vol 177 (2) ◽  
pp. 156-164
Author(s):  
Dariusz KURCZYŃSKI ◽  
Michał WARIANEK ◽  
Piotr ŁAGOWSKI
Keyword(s):  
Diesel Fuel ◽  
Combustion Process ◽  
Injection System ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Operating Cycle ◽  
Indicator Diagram ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
The Impact

The paper presents the results of the research on the uniqueness of the combustion process in the Perkins 1104D-E44TA engine already equipped with a Common Rail injection system, and then adapted on an engine test stand to dual-fuel operation. The result of the combustion process is an indicator diagram. The combustion process in the cylinder of the tested engine was evaluated by determining the uniqueness indicators of subsequent operating cycles, such as: the uniqueness indicator for the maximum pressure of the operating cycle, the uniqueness indicator for the mean indicated pressure, the uniqueness indicator for the indicated diagram and the uniqueness indicator for the partial indicator diagram. The conducted tests and the analysis of the results showed the impact of dual-fuel power supply of the tested engine on the combustion process, as compared to supplying the engine only with diesel fuel, for which it has been optimized.

Ion Current, Combustion and Emission Characteristics in an Automotive Common Rail Diesel Engine

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Naeim A. Henein ◽  
Tamer Badawy ◽  
Nilesh Rai ◽  
Walter Bryzik
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Common Rail ◽  
Ion Current ◽  
Injection System ◽  
Feedback Signal ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
No Emissions

Advanced electronically controlled diesel engines require a feedback signal to the ECU to adjust different operating parameters and meet demands for power, better fuel economy and low emissions. Different types of in-cylinder combustion sensors are being considered to produce this signal. This paper presents results of an experimental investigation on the characteristics of the ion current in an automotive diesel engine equipped with a common rail injection system. The engine is a 1.9 L, 4-cylinder, direct injection diesel engine. Experiments covered different engine loads and injection pressures. The relationships between the ion current, combustion parameters and engine out NO emissions and opacity are presented. The analysis of the experimental data identified possible sources of the ion current produced in diesel engines.

Experimental study of spray characteristics of biodiesel blending with diethyl carbonate in a common rail injection system

2017 ◽  
Vol 233 (2) ◽  
pp. 249-262 ◽  
Author(s):  
Wei Fu ◽  
Lanbo Song ◽  
Tao Liu ◽  
Qizhao Lin
Keyword(s):  
Cone Angle ◽  
Injection Pressure ◽  
Injection System ◽  
Diethyl Carbonate ◽  
Spray Characteristics ◽  
Projected Area ◽  
Spray Cone Angle ◽  
Spray Cone ◽  
Common Rail Injection System ◽  
Common Rail Injection

The objective of this paper is to investigate the spray macroscopic characteristics of biodiesel, diethyl carbonate (DEC)-biodiesel blends and diesel fuel based on a common-rail injection system. The spray tip penetration, spray cone angle and the spray projected area were measured through a high-speed photography method. The experimental results reveal that injection pressure and ambient pressure have significant effects on the spray characteristics. Higher injection pressure makes the spray tip penetration increase, while higher back pressure inside the chamber leads to the enlargement of the spray cone angle. The addition of DEC causes the blends fuels to have a shorter penetration and larger spray projected area, which reveals the potential capacity to improve the atomization process compared with biodiesel. The estimation of spray droplet size indicates that DEC30 generates a smaller Sauter mean diameter (SMD) because of its lower surface tension and viscosity. Model predictions were illustrated and compared with current work.

Sign in / Sign up

Export Citation Format

Share Document