Remote Sensing of Fuel Systems Using Real-Time 1D CFD

2012 ◽  
Author(s):  
Matthew Viele ◽  
Isaac Liu ◽  
Guoqiang Wang ◽  
Hugo Andrade ◽  
Bryan Willson
Keyword(s):  
Real Time ◽  
Simulation Software ◽  
Time Model ◽  
Virtual Sensors ◽  
One Dimensional ◽  
Cfd Models ◽  
Physical Sensors ◽  
Field Programmable ◽  
Engine Systems ◽  
Single Processor

Many modern engine systems are designed using one-dimensional computational fluid dynamics (1D CFD). This same technique can be used to model these systems in real time. This real-time model can be used to create virtual sensors in places where due to environmental or cost reasons physical sensors would not be practical. Achieving real-time performance of the CFD model requires more throughput than is available on single processor systems, so an Field Programmable Gate Array (FPGA) is employed. By employing an FPGA, we can synthesize and reconfigure our system to ensure determinism and lower resource usage. We instantiate several dedicated processing cores for parallel processing of sub-volumes. The number of cores can be configured to support up to 500 fluid volumes, more than enough for common 1D CFD models used in engines. This paper evaluates the feasibility of such a system and evaluates the complexity of such models against the GT-SUITE simulation software.

scholarly journals Real-Time Controller Design Test Bench for High-Voltage Direct Current Modular Multilevel Converters

2020 ◽  
Vol 10 (17) ◽  
pp. 6004 ◽  
Author(s):  
Saddaqat Ali ◽  
Jahangir Badar ◽  
Faheem Akhter ◽  
Syed Sabir Hussain Bukhari ◽  
Jong-Suk Ro
Keyword(s):  
Real Time ◽  
Controller Design ◽  
Simulation Software ◽  
Control Algorithms ◽  
Time Model ◽  
Multilevel Converters ◽  
Novel Approach ◽  
Modular Multilevel Converters ◽  
Labview Fpga ◽  
Complete Circuit

Modular multilevel converters (MMCs), with their inherent features and advantages over other conventional converters, have gained popularity and remain an ongoing topic of research. Many scholars have solved issues related to the operation, control, protection, and reliability of MMCs using simulation software and small hardware prototypes. We propose a novel approach for an MMC controller design with real-time systems. By utilizing a key benefit of LabVIEW Multisim co-simulation, an MMC control algorithm that can be deployed on a field-programmable gate array (FPGA) was developed in LabVIEW. The complete circuit was designed in Multisim, and a co-simulation was performed to drive an MMC model. The benefit of this topology is that control algorithms can be designed in a LabVIEW FPGA and tested with the Multisim co-simulation circuit to obtain simulation results. Once the controller works and provides satisfactory results, the same algorithm can be deployed in any NI (National Instruments) FPGA-based controller, like a compact remote input/output (RIO), to control real-time MMCs designed in an NI PCI eXtensions for Instrumentation (PXI) system. This method saves time and provides flexibility for effectively designing control algorithms and implementing them in an FPGA for real-time model implementation.

A Highly Efficient and Optimised Simulation Based Multi objective Decision-Making for FMS Control

2018 ◽  
Vol 6 (6) ◽  
pp. 98
Author(s):  
Shreyanshu Parhi ◽  
S. C. Srivastava
Keyword(s):  
Decision Making ◽  
Real Time ◽  
Manufacturing Industry ◽  
Simulation Software ◽  
Shop Floor ◽  
Simulation Tool ◽  
Routing Flexibility ◽  
Decision System ◽  
Multi Objective ◽  
Arena Simulation

Optimized and efficient decision-making systems is the burning topic of research in modern manufacturing industry. The aforesaid statement is validated by the fact that the limitations of traditional decision-making system compresses the length and breadth of multi-objective decision-system application in FMS.  The bright area of FMS with more complexity in control and reduced simpler configuration plays a vital role in decision-making domain. The decision-making process consists of various activities such as collection of data from shop floor; appealing the decision-making activity; evaluation of alternatives and finally execution of best decisions. While studying and identifying a suitable decision-making approach the key critical factors such as decision automation levels, routing flexibility levels and control strategies are also considered. This paper investigates the cordial relation between the system ideality and process response time with various prospective of decision-making approaches responsible for shop-floor control of FMS. These cases are implemented to a real-time FMS problem and it is solved using ARENA simulation tool. ARENA is a simulation software that is used to calculate the industrial problems by creating a virtual shop floor environment. This proposed topology is being validated in real time solution of FMS problems with and without implementation of decision system in ARENA simulation tool. The real-time FMS problem is considered under the case of full routing flexibility. Finally, the comparative analysis of the results is done graphically and conclusion is drawn.

Real-time signal processing in field programmable gate array based digital gamma-ray spectrometer

2020 ◽  
Vol 91 (10) ◽  
pp. 104707
Author(s):  
Yinyu Liu ◽  
Hao Xiong ◽  
Chunhui Dong ◽  
Chaoyang Zhao ◽  
Quanfeng Zhou ◽  
...  
Keyword(s):  
Signal Processing ◽  
Real Time ◽  
Field Programmable Gate Array ◽  
Gamma Ray ◽  
Time Signal ◽  
Gamma Ray Spectrometer ◽  
Field Programmable ◽  
Gate Array ◽  
Real Time Signal Processing

Accelerating laser processes with a smart two-dimensional polygon mirror scanner for ultra-fast beam deflection

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Florian Roessler ◽  
André Streek
Keyword(s):  
Energy Distribution ◽  
Real Time ◽  
Laser Processing ◽  
High Speed ◽  
Beam Deflection ◽  
Two Dimensional ◽  
Heat Accumulation ◽  
Field Programmable ◽  
Drill Holes ◽  
Average Laser

Abstract In laser processing, the possible throughput is directly scaling with the available average laser power. To avoid unwanted thermal damage due to high pulse energy or heat accumulation during MHz-repetition rates, energy distribution over the workpiece is required. Polygon mirror scanners enable high deflection speeds and thus, a proper energy distribution within a short processing time. The requirements of laser micro processing with up to 10 kW average laser powers and high scan speeds up to 1000 m/s result in a 30 mm aperture two-dimensional polygon mirror scanner with a patented low-distortion mirror configuration. In combination with a field programmable gate array-based real-time logic, position-true high-accuracy laser switching is enabled for 2D, 2.5D, or 3D laser processing capable to drill holes in multi-pass ablation or engraving. A special developed real-time shifter module within the high-speed logic allows, in combination with external axis, the material processing on the fly and hence, processing of workpieces much larger than the scan field.

scholarly journals The Design of a 2D Graphics Accelerator for Embedded Systems

Electronics ◽  
2021 ◽  
Vol 10 (4) ◽  
pp. 469
Author(s):  
Hyun Woo Oh ◽  
Ji Kwang Kim ◽  
Gwan Beom Hwang ◽  
Seung Eun Lee
Keyword(s):  
Embedded Systems ◽  
Embedded System ◽  
Real Time ◽  
Line Drawing ◽  
Cmos Process ◽  
Embedded Processor ◽  
Processor Core ◽  
Field Programmable ◽  
The Embedded System ◽  
Graphics Processing

Recently, advances in technology have enabled embedded systems to be adopted for a variety of applications. Some of these applications require real-time 2D graphics processing running on limited design specifications such as low power consumption and a small area. In order to satisfy such conditions, including a specific 2D graphics accelerator in the embedded system is an effective method. This method reduces the workload of the processor in the embedded system by exploiting the accelerator. The accelerator assists the system to perform 2D graphics processing in real-time. Therefore, a variety of applications that require 2D graphics processing can be implemented with an embedded processor. In this paper, we present a 2D graphics accelerator for tiny embedded systems. The accelerator includes an optimized line-drawing operation based on Bresenham’s algorithm. The optimized operation enables the accelerator to deal with various kinds of 2D graphics processing and to perform the line-drawing instead of the system processor. Moreover, the accelerator also distributes the workload of the processor core by removing the need for the core to access the frame buffer memory. We measure the performance of the accelerator by implementing the processor, including the accelerator, on a field-programmable gate array (FPGA), and ascertaining the possibility of realization by synthesizing using the 180 nm CMOS process.

Sign in / Sign up

Export Citation Format

Share Document