Quasi-Static Capillary Impregnation of a Porous Fiber Bed

1999 ◽  
Author(s):  
J. He ◽  
M. C. Altan
Keyword(s):  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Capillary Forces ◽  
Bond Number ◽  
Contact Angles ◽  
Flow Equation ◽  
Creeping Flow ◽  
Experimental Result ◽  
Fiber Volume ◽  
Front Motion

Abstract The impregnation of a fiber bed by capillary forces in a gravity field is analyzed. Fiber bed is modeled as infinitely long, parallel cylinders arranged in a hexagonal pattern. Quasi-static creeping flow equation is used to obtain the fluid front location and shape during impregnation of the fiber bed. The fluid front motion during impregnation are presented for different Bond numbers, contact angles and fiber volume fractions. It is found that impregnation velocity is significantly affected by contact angle and fiber volume fraction at the initial stages of impregnation. The influence of the Bond number becomes more significant when the fluid front approaches its final position where gravity balances capillary forces. The permeability of the fiber bed is also obtained from the time-dependent motion of the fluid front. The permeability predictions agree with the published experimental result and with those obtained by using lubrication theory.

Monitoring of mechanical properties of prestressed glass fiber epoxy composites over 12 months after fabrication

2021 ◽  
pp. 002199832110047
Author(s):  
Mahmoud Mohamed ◽  
Siddhartha Brahma ◽  
Haibin Ning ◽  
Selvum Pillay
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Flexural Strength ◽  
Compressive Residual Stress ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Epoxy Composites ◽  
Flexural Properties ◽  
Initial Increase ◽  
Fiber Volume

Fiber prestressing during matrix curing can significantly improve the mechanical properties of fiber-reinforced polymer composites. One primary reason behind this improvement is the generated compressive residual stress within the cured matrix, which impedes cracks initiation and propagation. However, the prestressing force might diminish progressively with time due to the creep of the compressed matrix and the relaxation of the tensioned fiber. As a result, the initial compressive residual stress and the acquired improvement in mechanical properties are prone to decline over time. Therefore, it is necessary to evaluate the mechanical properties of the prestressed composites as time proceeds. This study monitors the change in the tensile and flexural properties of unidirectional prestressed glass fiber reinforced epoxy composites over a period of 12 months after manufacturing. The composites were prepared using three different fiber volume fractions 25%, 30%, and 40%. The results of mechanical testing showed that the prestressed composites acquired an initial increase up to 29% in the tensile properties and up to 32% in the flexural properties compared to the non-prestressed counterparts. Throughout the 12 months of study, the initial increase in both tensile and flexural strength showed a progressive reduction. The loss ratio of the initial increase was observed to be inversely proportional to the fiber volume fraction. For the prestressed composites fabricated with 25%, 30%, and 40% fiber volume fraction, the initial increase in tensile and flexural strength dropped by 29%, 25%, and 17%, respectively and by 34%, 26%, and 21%, respectively at the end of the study. Approximately 50% of the total loss took place over the first month after the manufacture, while after the sixth month, the reduction in mechanical properties became insignificant. Tensile modulus started to show a very slight reduction after the fourth/sixth month, while the flexural modulus reduction was observed from the beginning. Although the prestressed composites displayed time-dependent losses, their long-term mechanical properties still outperformed the non-prestressed counterparts.

scholarly journals Effect of Fiber Volume Fraction on Behavior of Concrete Beams Made with Recycled Concrete Aggregates

2019 ◽  
Vol 253 ◽  
pp. 02004
Author(s):  
Wael Alnahhal ◽  
Omar Aljidda
Keyword(s):  
Fiber Volume Fraction ◽  
Concrete Beams ◽  
Volume Fraction ◽  
Recycled Concrete ◽  
Flexural Behavior ◽  
Beam Specimen ◽  
Rc Beam ◽  
Fiber Volume ◽  
Concrete Aggregates ◽  
Recycled Concrete Aggregates

This study investigates the effect of using different volume fractions of basalt macro fibers (BMF) on the flexural behavior of concrete beams made with 100% recycled concrete aggregates (RCA) experimentally. A total of 4 reinforced concrete (RC) beam specimens were flexural tested until failure. The parameter investigated included the BMF volume fraction (0%, 0.5%, 1%, and 1.5%). The testing results of the specimens were compared to control beam specimen made with no added fibers. The experimental results showed that adding BMF improves the flexural capacity of the tested beams.

The Effects of Fiber Volume Fraction on the Experiment Modal Behavior of 45°/-45° Carbon Fiber Plain Woven Fabric/Epoxy Resin Composites

2012 ◽  
Vol 583 ◽  
pp. 150-153
Author(s):  
Qian Liu ◽  
Xiao Yuan Pei ◽  
Jia Lu Li
Keyword(s):  
Carbon Fiber ◽  
Epoxy Resin ◽  
Natural Frequency ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Laminated Composites ◽  
Woven Fabric ◽  
Resin Composites ◽  
Fiber Volume ◽  
Epoxy Resin Composites

The modal properties of carbon fiber woven fabric (with fiber orientation of 45°/-45°) / epoxy resin composites with different fiber volume fraction were studied by using single input and single output free vibration of cantilever beam hammering modal analysis method. The effect of different fiber volume fraction on the modal parameters of laminated composites was analyzed. The experimental results show that with the fiber volume fraction increasing, the natural frequency of laminated composites becomes larger and damping ratio becomes smaller. The fiber volume fraction smaller, the peak value of natural frequency becomes lower and the attenuating degree of acceleration amplitude becomes faster.

Determination of fiber volume fraction in a cured laminate

2021 ◽  
pp. 002199832110112
Author(s):  
Qing Yang Steve Wu ◽  
Nan Zhang ◽  
Weng Heng Liew ◽  
Vincent Lim ◽  
Xiping Ni ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Volume Fraction ◽  
Evaluation Method ◽  
Volume Fraction ◽  
Matrix Material ◽  
Volume Ratio ◽  
Gravimetric Analysis ◽  
Fiber Volume ◽  
Laser Ultrasonic ◽  
The Matrix

Propagation of ultrasonic wave in Carbon Fiber Reinforced Polymer (CFRP) is greatly influenced by the material’s matrix, resins and fiber volume ratio. Laser ultrasonic broadband spectral technique has been demonstrated for porosity and fiber volume ratio extraction on unidirection aligned CFRP laminates. Porosity in the matrix materials can be calculated by longitudinal wave attenuation and accurate fiber volume ratio can be derived by combined velocity through the high strength carbon fiber and the matrix material with further consideration of porosity effects. The results have been benchmarked by pulse-echo ultrasonic tests, gas pycnometer and thermal gravimetric analysis (TGA). The potentials and advantages of the laser ultrasonic technique as a non-destructive evaluation method for CFRP carbon fiber volume fraction evaluation were demonstrated.

ACHIEVING REALISTIC TOW FIBER VOLUME FRACTIONS IN TEXTILE COMPOSITE MODELS BY INDUCING FIBER ENTANGLEMENT

2021 ◽  
Author(s):  
GEORGE BARLOW ◽  
MATHEW SCHEY ◽  
SCOTT STAPLETON
Keyword(s):  
Process Simulation ◽  
Manufacturing Process ◽  
Fiber Bundle ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Simulation Method ◽  
Textile Composite ◽  
Compression Pressure ◽  
Fiber Volume ◽  
Composite Models

Modeling composites can be an effective way to understand how a part will perform without requiring the destruction of costly specimens. By combining artificial fiber entanglement with manufacturing process simulation, a method was developed to create fiber bundle models using entanglement to control the fiber volume fraction. This fiber entanglement generation uses three parameters, probability of swapping (p_(r_S )), swapping radius standard deviation (r_(σ_S )), and the swapping plane spacing (l_S), to control the amount of entanglement within the fiber bundle. A parametric study was conducted and found that the more entanglement within a fiber bundle, the more compression mold pressure required to compact the fiber bundle to the same fiber volume fraction as that required for a less entangled bundle. This artificial fiber entanglement and manufacturing process simulation method for creating fiber bundles shows the potential to be able to create bundles with controlled final volume fraction using a desired mold compression pressure.

Performance of Bamboo Fiber Reinforced Composites: Mechanical Properties

2021 ◽  
Vol 879 ◽  
pp. 284-293
Author(s):  
Norliana Bakar ◽  
Siew Choo Chin
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Ester ◽  
Fiber Volume Fraction ◽  
Volume Fraction ◽  
Bamboo Fiber ◽  
Synthetic Fiber ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Volume Fractions

Fiber Reinforced Polymer (FRP) made from synthetic fiber had been widely used for strengthening of reinforced concrete (RC) structures in the past decades. Due to its high cost, detrimental to the environment and human health, natural fiber composites becoming the current alternatives towards a green and environmental friendly material. This paper presents an investigation on the mechanical properties of bamboo fiber reinforced composite (BFRC) with different types of resins. The BFRC specimens were prepared by hand lay-up method using epoxy and vinyl-ester resins. Bamboo fiber volume fractions, 30%, 35%, 40%, 45% and 50% was experimentally investigated by conducting tensile and flexural test, respectively. Results showed that the tensile and flexural strength of bamboo fiber reinforced epoxy composite (BFREC) was 63.2% greater than the bamboo fiber reinforced vinyl-ester composite (BFRVC). It was found that 45% of bamboo fiber volume fraction on BFREC exhibited the highest tensile strength compared to other BFRECs. Meanwhile, 40% bamboo fiber volume fraction of BFRVC showed the highest tensile strength between bamboo fiber volume fractions for BFRC using vinyl-ester resin. Studies showed that epoxy-based BFRC exhibited excellent results compared to the vinyl-ester-based composite. Further studies are required on using BFRC epoxy-based composite in various structural applications and strengthening purposes.

Sign in / Sign up

Export Citation Format

Share Document