Simulation of Backward Film Cooling at Gas Turbine Operating Conditions With and Without Mist Injection

2011 ◽  
Author(s):  
Ganesh Subbuswamy ◽  
Xianchang Li
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Blowing Ratio ◽  
Flow Mixing ◽  
Cylindrical Holes

The cooling of gas turbines is critical for engines’ efficiency as well as safety and lifetime. Film cooling has been used to cool the turbine blades for many years. The main issues related to film cooling are its poor coverage, aerodynamic loss, and increase of heat transfer coefficient due to strong flow mixing. To overcome these problems, film cooling with backward injection has been found to produce a more uniform cooling coverage under low pressure and temperature conditions and with simple cylindrical holes. The performance of film cooling with backward injection at gas turbine operating conditions is studied with numerical simulation in this paper. Effects of the blowing ratios and angles are examined. It is seen that the cooling coverage is generally much more uniform by using backward injection at gas turbine operating conditions, and in some cases the film cooling effectiveness can be almost doubled when compared to forward injection. The backward injection also shows its advantage when the blowing angle and blowing ratio change. However, mist (droplets) injection does not affect the cooling performance of the backward jet at the conditions under study. The best case of film cooling in this study is the fan-shaped hole with backward injection.

Numerical Simulation on Gas Turbine Film Cooling of Curved Surface With Backward Injection

2012 ◽  
Author(s):  
Shashank Shetty ◽  
Xianchang Li ◽  
Ganesh Subbuswamy
Keyword(s):  
Numerical Simulation ◽  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Strong Mixing ◽  
Inlet Temperature ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss

Due to the unique role of gas turbine engines in power generation and aircraft propulsion, significant effort has been made to improve the gas turbine performance. As a result, the turbine inlet temperature is usually elevated to be higher than the metal melting point. Therefore, effective cooling of gas turbines is a critical task for engines’ efficiency as well as safety and lifetime. Film cooling has been used to cool the turbine blades for many years. The main issues related to film cooling are its poor coverage, aerodynamic loss, and increase of heat transfer coefficient due to strong mixing. To overcome these problems, film cooling with backward injection has been found to produce a more uniform cooling coverage under low pressure and temperature conditions and with simple cylindrical holes. Therefore, the focus of this paper is on the performance of film cooling with backward injection at gas turbine operating conditions. By applying numerical simulation, it is observed that along the centerline on both concave and convex surfaces, the film cooling effectiveness decreases with backward injection. However, cooling along the span is improved, resulting in more uniform cooling.

Effect of blowing ratio on Film-Cooling effectiveness of Ginkgo Shaped Holes: A numerical approach

2021 ◽  
Author(s):  
Muhammad Awais ◽  
Reaz Hasan ◽  
Md. Hamidur Rahman
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Thermal Protection ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Bottom Surface ◽  
Inlet Temperature ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Lift Off

Modern gas turbine engines operate at significantly high temperatures to improve thermal efficiency and power output to a greater extent. The enhancement in rotor inlet temperature (RIT) increases the heat transfer rate to the turbine blades which requires sophisticated cooling schemes to maintain the blade temperature in acceptable levels. Therefore, the present work refers to the numerical investigation of film cooling technique applied in gas turbines. The cooling performance of two different shaped holes namely Ginkgo Forward (GF) and Ginkgo Reverse (GR)) were investigated in terms of centerline and local lateral effectiveness and comprehensive comparison was made with the cooling performance of cylindrical (CY) hole. The investigations were performed at two density ratios (DR=1.6, 2.0) and three different blowing ratios (BR=1.0, 1.5 and 2.0). At all the operating conditions, the results demonstrated significant augmentation in centerline and lateral effectiveness when GR shaped hole was employed followed by the GF and CY cooling holes. For shaped holes, the low velocity gradient through the film alleviated jet lift off and turbulence intensity resulting in decreased entrainment of hot gas to bottom surface. To conclude, the lateral coverage due to the shaped cooling holes significantly enhanced the thermal protection and overall cooling performance.

scholarly journals Heat Transfer Phenomena in Gas Turbines

1980 ◽  
Author(s):  
J. R. Taylor
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Gas Turbine Engine ◽  
Transfer Coefficients ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients

A discussion of the problems encountered in prediction of heat transfer in the turbine section of a gas turbine engine is presented. Areas of current gas turbine engine is presented. Areas of current concern to designers where knowledge is deficient or lacking are elucidated. Consideration is given to methods and problems associated with determination of heat transfer coefficients, external gas temperatures, and, where applicable, film cooling effectiveness. The paper is divided into parts dealing with turbine airfoil heat transfer, endwall heat transfer, and heat transfer in the internal cavities of cooled turbine blades. Recent literature dealing with these topics is listed.

scholarly journals An Experiment Investigation of Film Cooling Effectivenes of Sister Hole of Cylindrical Shaped Hole Film Cooling Geometry on a Flat Plate Surface

2015 ◽  
Vol 773-774 ◽  
pp. 309-322
Author(s):  
Muhammad Haziq Md Yazid ◽  
Hamidon Salleh
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
Operating Temperature ◽  
Cost Effective ◽  
Vital Role ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Shaped Hole

Gas turbines are widely used nowadays for aircraft propulsion and in land-based power generation or in the industrial application. The operating temperature of gas turbine has to be increased in order to increase their effectiveness. Thus, a cooling method known as film cooling is introduced to cool down the high operating temperature of the gas turbine. Film cooling is one of the effective methods in reducing the heat load to a turbine airfoil. This method is cost effective and by far the most common and widely researched method in the industry. Film cooling effectiveness plays a vital role in modern gas turbine technology. This present study will focus on sister holes that are attached to the primary holes at shallow angle of 30°, with 4 different blowing ratios ranging from 0.5 to 2.0. The roles of the different in blowing ratios are to observe the different values of film effectiveness presented by the sister holes design and to select the most effective blowing ratio that suits the design at shallow angle. From the results obtained, the usage of sister holes with shallow angle further increases the film cooling effectiveness particularly at low blowing ratio.

scholarly journals Effect of spherical blockage configurations on film cooling

2018 ◽  
Vol 22 (5) ◽  
pp. 1933-1942 ◽  
Author(s):  
Jin Wang ◽  
Ke Tian ◽  
Kai Zhang ◽  
Jakov Baleta ◽  
Bengt Sunden
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Rectangular Channel ◽  
Turbine Blades ◽  
Dust Particles ◽  
Inlet Temperature ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Lateral Film ◽  
Comparison Of The Results

With increasing inlet temperature of gas turbines, turbine blades need to be effectively protected by using cooling technologies. However, the deposition from the fuel impurities and dust particles in the air is often found inside film holes, which results in partial hole blockage. In this paper, the deposition geometry is simplified as a rectangular channel, and the effect of three blockage ratios is investigated by using the computational fluid dynamics. In addition, water droplets are also released from the coolant inlet to provide a comparison of the results with and without mist injection. It is found that the lateral film cooling effectiveness is reduced with increasing blockage ratio. For all the cases with the blowing ratio 0.6, 1% mist injection provides an improvement of the cooling performance by approximately 10%.

Numerical Predictions of Three-Dimensional Unsteady Turbulent Film-Cooling for Trailing Edge of Gas-Turbine Blade Using Large Eddy Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Ahmed Khalil ◽  
Hatem Kayed ◽  
Abdallah Hanafi ◽  
Medhat Nemitallah ◽  
Mohamed Habib
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Gas Turbine Blades ◽  
Blowing Ratio ◽  
Eddy Simulation

This work investigates the performance of film-cooling on trailing edge of gas turbine blades using unsteady three-dimensional numerical model adopting large eddy simulation (LES) turbulence scheme in a low Mach number flow regime. This study is concerned with the scaling parameters affecting effectiveness and heat transfer performance on the trailing edge, as a critical design parameter, of gas turbine blades. Simulations were performed using ANSYS-fluentworkbench 17.2. High quality mesh was adapted, whereas the size of cells adjacent to the wall was optimized carefully to sufficiently resolve the boundary layer to obtain insight predictions of the film-cooling effectiveness on a flat plate downstream the slot opening. Blowing ratio, density ratio, Reynolds number, and the turbulence intensity of the mainstream and coolant flow are optimally examined against the film-cooling effectiveness. The predicted results showed a great agreement when compared with the experiments. The results show a distinctive behavior of the cooling effectiveness with blowing ratio variation as it has a dip in vicinity of unity which is explained by the behavior of the vortex entrainment and momentum of coolant flow. The negative effect of the turbulence intensity on the cooling effectiveness is demonstrated as well.

The Effect of Using Ramps with Trench Cylindrical Holes on Film Cooling Effectiveness

2015 ◽  
Vol 3 (2) ◽  
pp. 15-27
Author(s):  
Ahmed A. Imram ◽  
Humam K. Jalghef ◽  
Falah F. Hatem
Keyword(s):  
Numerical Simulation ◽  
Film Cooling ◽  
Air Injection ◽  
Baseline Model ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Hot Air ◽  
Test Study ◽  
Cylindrical Holes

     The effect of introducing ramp with a cylindrical slot hole on the film cooling effectiveness has been investigated experimentally and numerically. The film cooling effectiveness measurements are obtained experimentally. A test study was performed at a single mainstream with Reynolds number 76600 at three different coolant to mainstream blowing ratios 1.5, 2, and 3. Numerical simulation is introduced to primarily estimate the best ramp configurations and to predict the behavior of the transport phenomena in the region linked closely to the interaction between the coolant air injection and the hot air mainstram flow. The results showed that using ramps with trench cylindrical holes would enhanced the overall film cooling effectiveness by 83.33% compared with baseline model at blowing ratio of 1.5, also  the best overall flim cooling effectevness was obtained at blowing ratio of 2 while it is reduced at blowing ratio of 3.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

Aerothermal Effect of Cavity Welding Beads on a Transonic Squealer Tip

2020 ◽  
Author(s):  
Joao Vieira ◽  
John Coull ◽  
Peter Ireland ◽  
Eduardo Romero
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Blade Tip ◽  
Mass Flow Rates

Abstract High pressure turbine blade tips are critical for gas turbine performance and are sensitive to small geometric variations. For this reason, it is increasingly important for experiments and simulations to consider real geometry features. One commonly absent detail is the presence of welding beads on the cavity of the blade tip, which are an inherent by-product of the blade manufacturing process. This paper therefore investigates how such welds affect the Nusselt number, film cooling effectiveness and aerodynamic performance. Measurements are performed on a linear cascade of high pressure turbine blades at engine realistic Mach and Reynolds numbers. Two cooled blade tip geometries were tested: a baseline squealer geometry without welding beads, and a case with representative welding beads added to the tip cavity. Combinations of two tip gaps and several coolant mass flow rates were analysed. Pressure sensitive paint was used to measure the adiabatic film cooling effectiveness on the tip, which is supplemented by heat transfer coefficient measurements obtained via infrared thermography. Drawing from all of this data, it is shown that the weld beads have a generally detrimental impact on thermal performance, but with local variations. Aerodynamic loss measured downstream of the cascade is shown to be largely insensitive to the weld beads.

Sign in / Sign up

Export Citation Format

Share Document