Experimental Investigation of an Open Loop Pulsating Heat Pipe Using Ferrofluid

2012 ◽  
Author(s):  
Maziar Mohammadi ◽  
Mehdi Taslimifar ◽  
Mohammad Hassan Saidi ◽  
Mohammad Behshad Shafii ◽  
Hossein Afshin ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
High Heat ◽  
Open Loop ◽  
Working Fluid ◽  
Distilled Water ◽  
Pulsating Heat Pipe ◽  
Resistance Variation

The present work investigates the thermal performance of a five turn Open Loop Pulsating Heat Pipe (OLPHP). The effects of working fluid namely water and ferrofluid, heat input, ferrofluid concentration, charging ratio, and orientation will be considered. Experimental results show that using ferrofluids can enhance the thermal performance in comparison with the case of distilled water. In addition, applying a magnetic field on the OLPHP charged with ferrofluid reduces its thermal resistance. Variation of the ferrofluid concentration results in different thermal performance of the OLPHP. Best charging ratio for the distilled water and ferrofluid without magnetic field is 60% in most of the cases, while in the case of ferrofluid in the presence of magnetic field at low heat inputs, 20% and at high heat inputs 60% of charging ratios have lowest thermal resistance.

Effects of Surface Coating of Nanoparticles on Thermal Performance of Open Loop Pulsating Heat Pipes

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Ali Adibnia ◽  
Hossein Afshin ◽  
Mohammad Hassan Saidi ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Surface Coating ◽  
Heat Pipes ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Performance Of Heat Transfer

Homogenous dispersing of nanoparticles in a base fluid is an excellent way to increase the thermal performance of heat transfer devices especially Heat Pipes (HPs). As a wickless, cheap and efficient heat pipe, Pulsating Heat Pipes (PHPs) are important candidates for thermal application considerations. In the present research an Open Loop Pulsating Heat Pipe (OLPHP) is fabricated and tested experimentally. The effects of working fluid namely, water, Silica Coated ferrofluid (SC ferrofluid), and ferrofluid without surface coating of nanoparticles (ferrofluid), charging ratio, heat input, and application of magnetic field on the overall thermal performance of the OLPHPs are investigated. Experimental results show that ferrofluid has better heat transport capability relative to SC ferrofluid. Furthermore, application of magnetic field improves the heat transfer performance of OLPHPs charged with both ferrofluids.

Thermal Performance of an Open Loop Pulsating Heat Pipe With Ferrofluid (Magnetic Nano-Fluid)

2012 ◽  
Author(s):  
Mehdi Taslimifar ◽  
Maziar Mohammadi ◽  
Mohammad Hassan Saidi ◽  
Hossein Afshin ◽  
Mohammad Behshad Shafii ◽  
...  
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Inclination Angle ◽  
Open Loop ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Degree Relative ◽  
Nano Fluid ◽  
Transfer Capability

In the present research an experimental investigation is performed to explore the effects of working fluid, heat input, ferrofluid concentration, magnets location, and inclination angle on the thermal performance of an Open Loop Pulsating Heat Pipe (OLPHP). Obtained results show that using ferrofluid can improve the thermal performance and applying a magnetic field on the water based ferrofluid decreases the thermal resistance. It shows that at an inclination angle of the OLPHP to be zero, the thermal performance of the present OLPHP reduces. Best heat transfer capability was achieved at 67.5 degree relative to horizontal axis for all of working fluids. Variation of the magnets location leads to a different thermal resistance in the OLPHP charged with ferrofluid.

Experimental Study of the Effects of Ferrofluid on Thermal Performance of a Pulsating Heat Pipe

2011 ◽  
Author(s):  
Maziar Mohammadi ◽  
Mohammad Mohammadi ◽  
Amir R. Ghahremani ◽  
M. B. Shafii
Keyword(s):  
Magnetic Field ◽  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Input ◽  
Pure Water ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Water Based ◽  
The Magnetic Field

In this work, a four-turn Pulsating Heat Pipe (PHP) is fabricated and tested experimentally. The novelty of the present PHP is the capability of obtaining various thermal performances at a specific heat input by changing the magnetic field. The effects of working fluid (water and ferrofluid), charging ratio (25%, 40%, and 55%), heat input (25, 35, 45, 55, 65, 75, and 85 W), orientation (vertical and horizontal heat mode), and magnetic field on the thermal performance of PHPs are investigated. The results showed that applying the magnetic field on the water based ferrofluid reduced the thermal resistance of PHP by a factor of 40.5% and 38.3% in comparison with the pure water case for the vertical and horizontal mode, respectively. According to the experimental results, an optimum thermal resistance of 0.38 °C/W was achieved at the following conditions: water-based ferrofluid as the working fluid in the presence of magnetic field, vertical mode, charging ratio of 55%, 7% volumetric concentration, and 85 W heat input. This thermal resistance is 11.5 times better than that of the empty PHP.

Promising Technology for Electronic Cooling: Nanofluidic Micro Pulsating Heat Pipes

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Kambiz Jahani ◽  
Maziar Mohammadi ◽  
Mohammad Behshad Shafii ◽  
Zahra Shiee
Keyword(s):  
Magnetic Field ◽  
Thermal Resistance ◽  
Thermal Management ◽  
Thermal Performance ◽  
Microelectromechanical Systems ◽  
Heat Pipes ◽  
Electronic Cooling ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Thermal Management Of Electronics

Currently, the thermal management of microelectromechanical systems (MEMS) has become a challenge. In the present research, a micro pulsating heat pipe (MPHP) with a hydraulic diameter of 508 μm, is experimented. The thermal performance of the MPHP in both the transient and steady conditions, the effects of the working fluid (water, silver nanofluid, and ferrofluid), heating power (4, 8, 12, 16, 20, 24, and 28 W), charging ratio (20, 40, 60, and 80%), inclination angle (0 deg, 25 deg, 45 deg, 75 deg, and 90 deg relative to horizontal axis), and the application of magnetic field, are investigated and thoroughly discussed. The experimental results show that the optimum charging ratio for water is 40%, while this optimum for nanofluids is 60%. In most of situations, the nanofluid charged MPHPs have a lower thermal resistance relative to the water charged ones. For ferrofluid charged MPHP, the application of a magnetic field substantially reduces the thermal resistance. This study proposes an outstanding technique for the thermal management of electronics.

Experimental Investigation of a Pulsating Heat Pipe Using Ferrofluid (Magnetic Nanofluid)

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Maziar Mohammadi ◽  
Mohammad Mohammadi ◽  
M. B. Shafii
Keyword(s):  
Magnetic Field ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Input ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Volumetric Concentration ◽  
Magnetic Nanofluid ◽  
Heat Mode ◽  
The Magnetic Field

In this work, a four-turn pulsating heat pipe (PHP) is fabricated and tested experimentally. The novelty of the present PHP is the capability to obtain various thermal performances at a specific heat input by changing the magnetic field. The effects of working fluid (water and ferrofluid), charging ratio (40% and 70%), heat input (35, 45, 55, 65, 75, and 85 W), orientation (horizontal and vertical heat mode), ferrofluid volumetric concentration (2.5% and 7%), and magnetic field on the thermal performance of PHPs are investigated. The results showed that applying the magnetic field on the water-based ferrofluid reduced the thermal resistance of PHP in all orientations. In the presence of a magnetic field, the best thermal performance was achieved at the higher charging ratios (70%) in all orientations.

scholarly journals Numerical Study on the Effects of using Nanofluids in Pulsating Heat Pipe

2018 ◽  
Vol 7 (4.35) ◽  
pp. 204
Author(s):  
M. Zufar ◽  
P. Gunnasegaran ◽  
Ng K. Ching
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Pulsating Heat Pipe ◽  
Working Fluids ◽  
Resistance Value

Pulsating Heat Pipe (PHP) is the next generation heat pipe that has a prospect in improving the heat transfer performance. The type of working fluid use in the PHP has a direct influence on the thermal performance. Incorporating nanofluid in PHP may greatly increase its thermal performance as compared to using base fluid (water). The current work focuses on the simulations of 2-dimensional flows in PHP using working fluids such as diamond, silver (Ag), silica oxide (SiO2) nanofluids and water. Constant heat flux and filling ratio of 50% were used throughout the study. From the results, it was found out that diamond nanofluid has the lowest thermal resistance value as compared to other working fluids. The effect of the number of PHP turns was studied and it was discovered that higher number of turns would produce lower thermal resistance value.

scholarly journals Integration of a Pulsating Heat Pipe in a Flat Plate Heat Sink

2014 ◽  
Author(s):  
Mitchell P. Hoesing ◽  
Gregory J. Michna
Keyword(s):  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Heat Sink ◽  
New Technologies ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Pulsating Heat Pipe ◽  
Plate Heat

The ongoing development of faster and smaller electronic components has led to a need for new technologies to effectively dissipate waste thermal energy. The pulsating heat pipe (PHP) shows potential to meet this need, due to its high heat flux capacity, simplicity, and low cost. A 20-turn flat plate PHP was integrated into an aluminum flat plate heat sink with a simulated electronic load. The PHP heat sink used water as the working fluid and had 20 parallel channels with dimensions 2 mm × 2 mm × 119 mm. Experiments were run under various operating conditions, and thermal resistance of the PHP was calculated. The performance enhancement provided by the PHP was assessed by comparing the thermal resistance of the heat sink with no working fluid to that of it charged with water. Uncharged, the PHP was found to have a resistance of 1.97 K/W. Charged to a fill ratio of approximately 75% and oriented vertically, the PHP achieved a resistance of .49 K/W and .53 K/W when the condenser temperature was set to 20°C and 30°C, respectively. When the PHP was tilted to 45° above horizontal the PHP had a resistance of .76 K/W and .59 K/W when the condenser was set 20°C and 30°C, respectively. The PHP greatly improves the heat transfer properties of the heat sink compared to the aluminum plate alone. Additional considerations regarding flat plate PHP design are also presented.

Experimental Investigation of the Miniature Loop Heat Pipe With Flat Evaporator

2005 ◽  
Author(s):  
Randeep Singh ◽  
Aliakbar Akbarzadeh ◽  
Masataka Mochizuki ◽  
Thang Nguyen ◽  
Vijit Wuttijumnong
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Control ◽  
Capillary Forces ◽  
High Heat ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Wick Structure ◽  
Flat Evaporator ◽  
Heat Loads

Loop heat pipe (LHP) is a very versatile heat transfer device that uses capillary forces developed in the wick structure and latent heat of evaporation of the working fluid to carry high heat loads over considerable distances. Robust behaviour and temperature control capabilities of this device has enable it to score an edge over the traditional heat pipes. In the past, LHPs has been invariably assessed for electronic cooling at large scale. As the size of the thermal footprint and available space is going down drastically, miniature size of the LHP has to be developed. In this paper, results of the investigation on the miniature LHP (mLHP) for thermal control of electronic devices with heat dissipation capacity of up to 70 W have been discussed. Copper mLHP with disk-shaped flat evaporator 30 mm in diameter and 10 mm thickness was developed. Flat evaporators are easy to attach to the heat source without any need of cylinder-plane-reducer saddle that creates additional thermal resistance in the case of cylindrical evaporators. Wick structure made from sintered nickel powder with pore size of 3–5 μm was able to provide adequate capillary forces for the continuos circulation of the working fluid, and successfully transport heat load at the required distance of 60 mm. Heat was transferred using 3 mm ID copper tube with vapour and liquid lines of 60 mm and 200 mm length respectively. mLHP showed very reliable start up at different heat loads and was able to achieve steady state without any symptoms of wick dry-out. Tests were conducted on the mLHP with evaporator and condenser at the same level. Total thermal resistance, R total of the mLHP came out to be in the range of 1–4°C/W. It is concluded from the outcomes of the investigation that mLHP with flat evaporator can be effectively used for the thermal control of the electronic equipments with restricted space and high heat flux chipsets.

Operating Activity Visualization and Thermal Performance Measurement of Pulsating Heat Pipe

2016 ◽  
Vol 369 ◽  
pp. 42-47 ◽  
Author(s):  
Patrik Nemec ◽  
Zuzana Kolková ◽  
Milan Malcho
Keyword(s):  
Heat Transfer ◽  
Performance Measurement ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Vapour Phase ◽  
Working Fluid ◽  
Internal Diameter ◽  
Pulsating Heat Pipe ◽  
Inner Diameter ◽  
Thermo Physical Properties

Heat pipe is well known device which is used to heat transfer phase-change of working fluid. Pulsating heat pipe (PHP) is special type of heat pipe which heat transfer by pulsating movement of working fluid. Article deals about operating activity and thermal performance measurement of this special heat pipe. Operating activity visualization of PHP was performed with PHP made from glass. The two types of PHPs were made. The first PHP has internal diameter of tube 1 mm, second PHP has internal diameter of tube 1.5 mm and both PHPs have eleven meanders. The working fluids used in PHP were water and Fluorinert FC-72. These fluids were chose for their different thermo-physical properties and the visualization observe formation of liquid and vapour phase working fluid during filling process and working operation.Next, the article describes thermal performance measurement of PHP depending on working fluid amount and heat source temperature. Measurement was performed with PHP made from copper tube with inner diameter 1.5 mm curved to the twenty one meanders and filled with water. The results give us image about formation and distribution of working fluid in pulsating heat pipe and about influence of working fluid amount on the heat transfer ability of pulsating heat pipe.

Effect of Inclination Angle on the Closed Loop Pulsating Heat Pipe Thermal Performance

2013 ◽  
Author(s):  
Pramod R. Pachghare ◽  
Ashish M. Mahalle
Keyword(s):  
Thermal Resistance ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Inclination Angle ◽  
Heat Input ◽  
Closed Loop ◽  
Pulsating Heat Pipe ◽  
Working Fluids ◽  
Inclination Angles ◽  
R 134A

The closed loop pulsating heat pipe (CLPHP) is a passive two-phase heat transfer device, patented by Akachi (1990). Due to its excellent features, PHP has been considered as one of the promising technologies for electronic cooling, heat exchanger, etc. This paper presents an experimental study shows the effect of inclination angle on the thermal performance of CLPHP, which consist of 10 turns of copper tubes having inner and outer diameter 2 mm and 3.6 mm respectively. The equal lengths of evaporator, condenser and adiabatic sections are 50 mm each. Different working fluids are used as R-134a, Methanol and Water. For all experimentations, an optimum filling ratio was maintained 50% by volume. The thermal performance have been investigated with different inclination angles (viz. 0°, 20°, 40°, 60° and 90°) at various heat input from 5 to 50W in the steps of 5W. The thermal resistance (which is inversely proportional to thermal performance) of CLPHP at various heat input are plotted for different working fluids. The result shows that, the thermal resistance decreases as heat input increases. But at low heat input i.e. upto 25W, the thermal resistance decreases rapidly and the PHP performance is more sensitive to the inclination angle whereas high heat input i.e. above 25W, the thermal resistance decreases smoothly and less independent to the inclination angle. In all inclination angles, vertical bottom heat position (at 90°) of CLPHP gives best thermal performance due to presence of gravity force. At all inclination angles, the working fluid R-134a show best thermal performance followed by methanol and water.

Sign in / Sign up

Export Citation Format

Share Document