Ultimate Strength Assessment of Semi-Submersible Platform Under Different Load Conditions

2017 ◽  
Author(s):  
Yangzhe Yu ◽  
Guoqing Feng ◽  
Huilong Ren
Keyword(s):  
Finite Element ◽  
Ultimate Strength ◽  
High Stress ◽  
Initial Imperfection ◽  
Element Model ◽  
Nonlinear Finite Element ◽  
Main Bearing ◽  
Strength Assessment ◽  
Hull Structure ◽  
Load Conditions

The nonlinear finite-element method has been widely used in evaluating the ultimate strength of stiffened plates and part of hull girders, considering the effect of boundary conditions, geometrical initial imperfection and welding-induced residual stress in recent years. However, available research on the ultimate strength of large-sized structures, especially of semi-submersible platform is limited. New large-sized semi-submersible platform has been designed with lateral brace structure and square cross-section columns. The investigation of ultimate strength of the whole structure is of paramount importance in assessing the safety and design of such large structure. Therefore, in this paper, a three-dimensional nonlinear finite element model was developed to investigate the ultimate strength of a new generation of semi-submersible platform under different load conditions and its behavior after collapse using explicit dynamic solvers. Results showed that the time dependent dynamic explicit method was reliable and feasible for the calculation of ultimate strength of such complicated structure. For the target platform, the bracings and upper hull structure were the main bearing component and were critical for the ultimate strength of the whole structure. High stress occurred in connection areas and special attention shall be paid for.

scholarly journals Experimental and Numerical Investigations of Ultimate Strength of Imperfect Stiffened Plates of Different Slenderness

2020 ◽  
Vol 27 (4) ◽  
pp. 120-129
Author(s):  
Krzysztof Woloszyk ◽  
Yordan Garbatov ◽  
Jakub Kowalski ◽  
Leszek Samson
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Compressive Force ◽  
Initial Imperfection ◽  
Element Model ◽  
Stiffened Plates ◽  
Structural Behaviour ◽  
Middle Cross Section ◽  
Geometrical Imperfections

AbstractThe objective of this study is to analyse the behaviour of compressed stiffened plates of different slenderness using experimental and numerical methods. The presented results are part of a long-term project to investigate the ultimate strength of geometrically imperfect structures subjected to different degradation phenomena, including corrosion degradation and locked cracks. Several specimens were subjected to a uniaxial compressive force, and the most important quantities related to the structural behaviour were captured and analysed. A finite element model, accounting for material and geometrical nonlinearities and initial geometrical imperfections, was developed using the commercial software ANSYS. The residual welding-induced stresses were measured in the middle cross-section for two specimens. The initial imperfection was identified by employing a close-range photogrammetry approach. It was concluded that the numerical analyses, based on the finite element model, predict the ultimate strength of stiffened plates accurately, although some deviations were also observed. The detailed analysis with the indication of possible uncertainty is presented, and several conclusions are derived.

PHOTOGRAMMETRY MEASUREMENTS OF INITIAL IMPERFECTIONS FOR THE ULTIMATE STRENGTH ASSESSMENT OF PLATES

2021 ◽  
Vol 156 (A4) ◽  
Author(s):  
A Cubells ◽  
Y Garbatov ◽  
C Guedes Soares
Keyword(s):  
Finite Element ◽  
Ultimate Strength ◽  
Compressive Load ◽  
Initial Imperfection ◽  
Maximum Load ◽  
Surface Shape ◽  
Element Analysis ◽  
Strength Assessment ◽  
Load Carrying ◽  
Geometrical Imperfections

The objective of the present study is to develop a new approach to model the initial geometrical imperfections of ship plates by using Photogrammetry. Based on images, Photogrammetry is able to take measurements of the distortions of plates and to catch the dominant surface shape, including the deformations of the edges. Having this data, it is possible to generate faithful models of plate surface based on third order polynomial functions. Finally, the maximum load- carrying capacity of the plates is analysed by performing a nonlinear finite element analysis using a commercial finite element code. Three un-stiffened and four stiffened plates have been modelled and analysed. For each plate, two initial imperfection models have been generated one, based on photogrammetric measurements and the other, based on the trigonometric Fourier functions. Both models are subjected to the same uniaxial compressive load and boundary conditions in order to study the ultimate strength.

Quantify Resonance Inspection With Finite-Element-Based Modal Analyses

2010 ◽  
Author(s):  
K. Lai ◽  
X. Sun ◽  
C. Dasch
Keyword(s):  
Finite Element ◽  
High Stress ◽  
Mesh Size ◽  
Element Model ◽  
Sensitivity Study ◽  
Production Level ◽  
Mode Shapes ◽  
Resonance Spectroscopy ◽  
Frequency Spectra ◽  
Resonance Frequencies

Resonance inspection uses the natural acoustic resonances of a part to identify anomalous parts. Modern instrumentation can measure the many resonant frequencies rapidly and accurately. Sophisticated sorting algorithms trained on sets of good and anomalous parts can rapidly and reliably inspect and sort parts. This paper aims at using finite-element-based modal analysis to put resonance inspection on a more quantitative basis. A production-level automotive steering knuckle is used as the example part for our study. First, the resonance frequency spectra for the knuckle are measured with two different experimental techniques. Next, scanning laser vibrometry is used to determine the mode shape corresponding to each resonance. The material properties including anisotropy are next measured to high accuracy using resonance spectroscopy on cuboids cut from the part. Then, finite element model (FEM) of the knuckle is generated by meshing the actual part geometry obtained with computed tomography (CT). The resonance frequencies and mode shapes are next predicted with a natural frequency extraction analysis after extensive mesh size sensitivity study. The good comparison between the predicted and the experimentally measured resonance spectra indicate that finite-element-based modal analyses have the potential to be a powerful tool in shortening the training process and improving the accuracy of the resonance inspection process for a complex, production level part. The finite element based analysis can also provide a means to computationally test the sensitivity of the frequencies to various possible defects such as porosity or oxide inclusions especially in the high stress regions that the part will experience in service.

The Flattening Behaviour of Angle Section Beams Subjected to Pure Bending

2014 ◽  
Vol 501-504 ◽  
pp. 2479-2483
Author(s):  
Wei Bin Yuan ◽  
Chang Yi Chen
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Analytical Solutions ◽  
Element Model ◽  
Nonlinear Finite Element ◽  
Experimental Results ◽  
Energy Methods ◽  
Pure Bending ◽  
Angle Section ◽  
Nonlinear Finite Element Model

The flattening behaviour of angle section beams subjected to pure bending is studied in this paper. Analytical solutions for static instabilities of angle section beams subjected to pure bending about its weak axis are derived using energy methods. Nonlinear finite element model using the code ANSYS is developed to simulate nonlinear snap-through instability of angle section beams under pure bending. The optimization assumption about flattening shape of the leg is proposed, through comparison of between the present solutions, experimental results, and the finite element results.

Behaviour of cold-formed steel built-up I-section columns composed of four U-profiles

2018 ◽  
Vol 22 (3) ◽  
pp. 613-625 ◽  
Author(s):  
M Anbarasu ◽  
M Venkatesan
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Ultimate Strength ◽  
Element Model ◽  
Cross Sectional ◽  
Direct Strength Method ◽  
The North ◽  
Compression Members ◽  
Cross Sectional Dimension ◽  
Cold Formed Steel

This work reports numerical results concerning the cold-formed steel built-up I-section columns composed of four U-profiles under axial compression. A finite element model is developed by using the software program ABAQUS. The developed model includes geometric, material nonlinearities and geometric imperfections. The finite element model was verified against the experimental results reported in the cold-formed steel built-up open section columns. In the parametric study, the sections are analysed with several cross-sectional dimension ratios and lengths, in order to assess their influence on the buckling behaviour and ultimate strength of cold-formed steel built-up I-section columns. After presenting and discussing the numerical parametric results, the article shows that the current direct strength method in the North American Specification for cold-formed steel compression members design curve fails to predict adequately the ultimate strength of some of the columns analysed and addresses the modification proposed on current direct strength method curves, providing improved predictions of all the numerical ultimate strength available. The proposed method is also assessed by reliability analysis.

Static and Dynamic Analyses of the LSES Hull Structure

1978 ◽  
Vol 22 (02) ◽  
pp. 110-122
Author(s):  
A. S. Hananel ◽  
E. J. Dent ◽  
E. J. Philips ◽  
S. H. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Surface Effect ◽  
Three Dimensional ◽  
Element Model ◽  
Finite Element Program ◽  
Hull Structure ◽  
Surface Effect Ship ◽  
Hull Design ◽  
Element Program

To avoid the conservativeness in the large surface-effect ship hull design which results from simplifying assumptions in the stress analysis, the hull structure was analyzed as a three-dimensional elastic body. The NASTRAN finite-element program, level 15.0, was selected for use in this analysis as the most suitable program available. A finite-element model representing the true hull stiffness was used in obtaining the internal load and displacement distributions. The inertia effect of the ship masses was included with each set of static loads. This was done by using the Static Analysis with Inertia Relief solution included in NASTRAN. The stress redistribution around cutouts in the hull was treated in a separate study. The interaction between hull and deckhouse was investigated by attaching a model of the deckhouse onto the hull model, and then solving for the appropriate load conditions. The natural frequencies were obtained using a reduced finite-element model of both the hull and hull/deckhouse combination. A new technique was developed for determining the dynamic stresses and their proper superposition on the static stresses.

Sign in / Sign up

Export Citation Format

Share Document