Experimental Study of Performance and Exhaust Emissions of a VCR Diesel Engine Fuelled With Oxygenated Additives

2017 ◽  
Author(s):  
Ashish Nayyar ◽  
Dilip Sharma ◽  
Shyam Lal Soni ◽  
Alok Mathur
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Cetane Number ◽  
Exhaust Emissions ◽  
The Other ◽  
Ternary Blend ◽  
Binary Blends ◽  
Oxygenated Additives

This paper reports the results of a study to determine a ternary blend of oxygenated additives for reduction in smoke emissions in diesel engines. Initial studies on binary blends established twenty percent (by volume) n-butanol-diesel blend (B20) as the base fuel. Subsequently observations were taken with Nitromethane (NM)-n-butanol-diesel blends. It was observed that binary blends are not able to reduce smoke and other emissions beyond the optimum blending ratio (B20). Also, Cetane Number of binary blends was found to be lowered due to poor Cetane Number of n-butanol. It is therefore necessary to add another additive which helps in reducing smoke substantially and improve Cetane Number of blend without affecting the other parameters. The study found that blending of one percent of NM by volume gives best results for smoke reduction. The overall effect of this ternary blend is to reduce the smoke and NOx up to 69.76% and 5.4% respectively. It is concluded that NM-n-butanol-diesel blend would be a potential fuel for smoke reduction in diesel engines.

An Experimental Study of Normal-Hexadecane and Iso-Dodecane Binary Fuel Blends in a Military Diesel Engine

2012 ◽  
Author(s):  
Leonard J. Hamilton ◽  
Jim S. Cowart ◽  
Dianne Luning-Prak ◽  
Patrick A. Caton
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Fuel Injection ◽  
Cetane Number ◽  
Straight Chain ◽  
Load Range ◽  
Binary Blends ◽  
Engine Operation ◽  
Fuel Blends ◽  
Branched Alkanes

The molecular composition of new hydrotreated renewable fuels consists of both straight chain and branched alkanes. These new fuels do not contain aromatic or cyclo-paraffinic hydro-carbon compounds which are regularly seen in conventional petroleum fuels. Both experimental and modeling work has shown that straight chain alkanes have shorter ignition delays (e.g. higher cetane number) as compared to branched alkanes. In order to better understand the effects of branched and straight chain alkanes fuels in diesel engines, an experimental study was pursued using binary blends of iso-dodecane (iC12H26 with abbreviation: iC12) and normal-hexadecane (nC16H34 with abbreviation nC16) in a military diesel engine (AM General HMMWV ‘Humvee’ engine). Mixtures of 50% iC12 with 50% nC16 as well as 25% iC12 with 75% nC16 were compared to 100% nC16 (cetane) fueled engine operation across the entire speed-load range. Higher nC16 fuel content operation resulted in modestly earlier fuel injection events and combustion phasing that delievered slightly worse engine brake performance (torque and fuel consumption). Interestingly, ignition delay and overall burn durations were relatively insensitive to the binary blends tested. The significantly different physical properties of iC12 relative to nC16 are believed to affect the fuel injection event leading to later fuel injection with increasing iC12 content. Later injection into a hotter chamber mitigates the lower cetane number of the higher iC12 content fuel blends.

scholarly journals Experimental study of multiple pilot injection strategy in an automotive direct injection diesel engine

2018 ◽  
Vol 234 ◽  
pp. 03007
Author(s):  
Plamen Punov ◽  
Tsvetomir Gechev ◽  
Svetoslav Mihalkov ◽  
Pierre Podevin ◽  
Dalibor Barta
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Diesel Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection Timing ◽  
Pilot Injection ◽  
Injection Strategy ◽  
Direct Injection Diesel Engine ◽  
Rate Of Heat Release

The pilot injection strategy is a widely used approach for reducing the noise of the combustion process in direct injection diesel engines. In the last generation of automotive diesel engines up to several pilot injections could occur to better control the rate of heat release (ROHR) in the cylinder as well as the pollutant formation. However, determination of the timing and duration for each pilot injection needs to be precisely optimised. In this paper an experimental study of the pilot injection strategy was conducted on a direct injection diesel engine. Single and double pilot injection strategy was studied. The engine rated power is 100 kW at 4000 rpm while the rated torque is 320 Nm at 2000 rpm. An engine operating point determined by the rotation speed of 1400 rpm and torque of 100 Nm was chosen. The pilot and pre-injection timing was widely varied in order to study the influence on the combustion process as well as on the fuel consumption.

scholarly journals PENGARUH PENGGUNAAN ENERGI TERBARUKAN BUTANOL TERHADAP PENURUNAN EMISI JELAGA MESIN DIESEL INJEKSI LANGSUNG BERBAHAN BAKAR BIODIESEL CAMPURAN SOLAR DAN JATROPA

Infotekmesin ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 18-22
Author(s):  
Syarifudin Syarifudin ◽  
Syaiful Syaiful
Keyword(s):  
Fuel Consumption ◽  
Diesel Engines ◽  
Driving Forces ◽  
Direct Injection ◽  
Fuel Efficiency ◽  
Cetane Number ◽  
Calorific Value ◽  
Exhaust Emissions ◽  
High Viscosity ◽  
High Oxygen Content

Diesel engines are widely used as driving forces in vehicles and industry due to fuel efficiency and high output power. The wide use of diesel engines triggers an increase in fuel consumption and exhaust emissions that are harmful to health. Jatropha is a renewable fuel as a solution to increase fuel consumption. However, the high viscosity and low calorific value result in reduced performance and increased exhaust emissions. Butanol has a high oxygen content and cetane number and low viscosity compared to diesel and jatropha. Addition of butanol is possible to reduce the decrease in performance and exhaust emissions of diesel engines. this study evaluates the effect of butanol on reducing Isuzu 4JB1 diesel engine direct injection emissions. Percentage of blend used 70/30/0, 65/30/5, 60/30/10, and 55/40/15 based on volume. Tests are carried out at 2500 constant turns with a loading of 25% to 100% using the EGR system. The experimental results showed the presence of butanol caused a decrease in soot emissions produced by diesel engines

Experimental study on performance and exhaust emissions of a diesel engine fuelled with Ceiba pentandra biodiesel blends

2013 ◽  
Vol 76 ◽  
pp. 828-836 ◽  
Author(s):  
A.S. Silitonga ◽  
H.H. Masjuki ◽  
T.M.I. Mahlia ◽  
Hwai Chyuan Ong ◽  
W.T. Chong
Keyword(s):  
Experimental Study ◽  
Diesel Engine ◽  
Exhaust Emissions ◽  
Biodiesel Blends ◽  
Ceiba Pentandra

Exhaust Emission Characteristics of a Three-Wheeler Auto Diesel Engine Fueled with Pongamia, Mahua and Jatropha Biodiesels

2019 ◽  
Vol 13 ◽  
Author(s):  
Bobbili Prasadarao ◽  
Aditya Kolakoti ◽  
Pudi Sekhar
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Edible Oils ◽  
Cetane Number ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
International Standards ◽  
Exhaust Emission ◽  
Emission Characteristics

: This paper presents the production of biodiesel from three different non edible oils of Pongamia, Mahua and Jatropha as an alternative fuel for diesel engine. Biodiesel is produced by followed transesterification process, using catalyst sodium hydroxide (NaOH) and methyl alcohol (CH3OH). A single cylinder four stroke three-wheeler auto diesel engine is used to evaluate the exhaust emission characteristics at a constant speed of 1500rpm with varying loads. Diesel as a reference fuel and cent percent of Pongamia Methyl Ester (PME), Mahua Methyl Ester (MME) and Jatropha Methyl Ester (JME) are used as an alternative fuel. The physicochemical properties of biodiesels are within the limits of international standards (ASTM D6751) noticeably. The results of tested biodiesels offer low exhaust emissions compared to diesel fuel, owing to presence of molecular oxygen and high cetane number. At maximum load the NOx emission reduced by 18.41% for JME, 17.46% for MME and 7.61% for PME. Low levels of CO emissions are recorded for JME (66%) followed by MME (33%) and PME (22%). Unburnt hydrocarbon emissions were reduced by 85.75% for JME and MME, for PME 14.28% reduction is observed. Exhaust smoke emissions are also reduced for PME and MME by 18.84%, for JME 14.49%. As a conclusion, it is observed that all the methyl esters exhibit significant reduction in harmful exhaust emissions compared to diesel fuel and JME is noted as a better choice.

The On-Road Exhaust Emissions from Vehicles Fitted with the Start-Stop System

2013 ◽  
Vol 390 ◽  
pp. 343-349 ◽  
Author(s):  
Jerzy Merkisz ◽  
Pawel Fuc ◽  
Piotr Lijewski ◽  
Andrzej Ziolkowski
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Measurement System ◽  
Power Output ◽  
Gasoline Engine ◽  
Exhaust Emissions ◽  
The Other ◽  
Exhaust Emission ◽  
Traffic Conditions ◽  
Utility Vehicle

The paper describes the influence of the start-stop system on the exhaust emissions and fuel consumption. The tests were performed for two vehicles. The first one was a vehicle designed specifically to operate in city conditions. It was fitted with a gasoline engine of the displacement of 0.9 dm3 and maximum power output of 63.7 kW. The other vehicle was an SUV (Sports Utility Vehicle) fitted with a diesel engine of the displacement of 3.0 dm3. The measurements of the exhaust emission were carried out on the same route under actual traffic conditions. For the tests a portable exhaust emissions analyzer from the PEMS group SEMTECH DS was used (PEMS Portable Emissions Measurement System).

Sign in / Sign up

Export Citation Format

Share Document