Use of Seismic Analyses for the Wind Energy Industry

2017 ◽  
Author(s):  
Weifei Hu ◽  
S. C. Pryor ◽  
F. Letson ◽  
R. J. Barthelmie
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Condition Monitoring ◽  
Wind Farm ◽  
Spectral Power ◽  
Operating Conditions ◽  
Energy Industry ◽  
Ground Vibrations ◽  
Power Spectral ◽  
Sonic Anemometers

This paper proposes new seismic-based methods for use in the wind energy industry with a focus on wind turbine condition monitoring. Fourteen Streckeisen STS-2 Broadband seismometers and two 3D sonic anemometers are deployed in/near an operating wind farm to collect the data used in these proof-of-principle analyses. The interquartile mean (IQM) value of power spectral density (PSD) of the seismic components in 10-minute time series are used to characterize the spectral signatures (i.e. frequencies with enhanced variance) in ground vibrations deriving from vibrations of wind turbine subassemblies. A power spectral envelope approach is taken in which the probability density function of seismic PSD is developed using seismic data collected under normal turbine operation. These power spectral envelopes clearly show the energy distribution of wind-turbine-induced ground vibrations over a wide frequency range. Singular PSD lying outside the power spectral envelopes can be easily identified, and are used herein along with SCADA data to diagnose the associated sub-optimal turbine operating conditions. Illustrative examples are given herein for periods with yaw-misalignment and excess tower acceleration. It is additionally shown that there is a strong association between drivetrain acceleration and seismic spectral power in a frequency band of 2.5–12.5 Hz. The long-term goal of the research is development of seismic-based condition monitoring (SBCM) for wind turbines. The primary advantages of SBCM are that the approach is low-cost, non-invasive and versatile (i.e., one seismic sensor monitoring for multiple turbine subassemblies).

Use of Seismic Analyses for the Wind Energy Industry

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Weifei Hu ◽  
S. C. Pryor ◽  
Frederick Letson ◽  
R. J. Barthelmie
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Condition Monitoring ◽  
Wind Farm ◽  
Spectral Power ◽  
Operating Conditions ◽  
Energy Industry ◽  
Ground Vibrations ◽  
Power Spectral ◽  
Sonic Anemometers

This paper proposes new seismic-based methods for use in the wind energy industry with a focus on wind turbine condition monitoring. Fourteen Streckeisen STS-2 Broadband seismometers and two three-dimensional (3D) sonic anemometers are deployed in/near an operating wind farm to collect the data used in these proof-of-principle analyses. The interquartile mean (IQM) value of power spectral density (PSD) of the seismic components in 10 min time series is used to characterize the spectral signatures (i.e., frequencies with enhanced variance) in ground vibrations deriving from vibrations of wind turbine subassemblies. A power spectral envelope approach is taken in which the probability density function (PDF) of seismic PSD is developed using seismic data collected under normal turbine operation. These power spectral envelopes clearly show the energy distribution of wind-turbine-induced ground vibrations over a wide frequency range. Singular PSD lying outside the power spectral envelopes can be easily identified and is used herein along with supervisory control and data acquisition (SCADA) data to diagnose the associated suboptimal turbine operating conditions. Illustrative examples are given herein for periods with yaw misalignment and excess tower acceleration. It is additionally shown that there is a strong association between drivetrain acceleration and seismic spectral power in a frequency band of 2.5–12.5 Hz. The long-term goal of the research is development of seismic-based condition monitoring (SBCM) for wind turbines. The primary advantages of SBCM are that the approach is low-cost, noninvasive, and versatile (i.e., one seismic sensor monitoring multiple turbine components).

scholarly journals Inter-annual variability of wind climates and wind turbine annual energy production

2018 ◽  
Author(s):  
Sara C. Pryor ◽  
Tristan J. Shepherd ◽  
Rebecca J. Barthelmie
Keyword(s):  
Standard Deviation ◽  
Wind Energy ◽  
Wind Turbine ◽  
Energy Production ◽  
Wind Farm ◽  
Wind Farms ◽  
Wind Speeds ◽  
Annual Variability ◽  
Eastern Usa

Abstract. Inter-annual variability (IAV) of expected annual energy production (AEP) from proposed wind farms plays a key role in dictating project financing. IAV in pre-construction projected AEP and the difference in 50th and 90th percentile (P50 and P90) AEP derives in part from variability in wind climates. However, the magnitude of IAV in wind speeds at/close to wind turbine hub-heights is poorly constrained and maybe overestimated by the 6 % standard deviation of annual mean wind speeds that is widely applied within the wind energy industry. Thus there is a need for improved understanding of the long-term wind resource and the inter-annual variability therein in order to generate more robust predictions of the financial value of a wind energy project. Long-term simulations of wind speeds near typical wind turbine hub-heights over the eastern USA indicate median gross capacity factors (computed using 10-minute wind speeds close to wind turbine hub-heights and the power curve of the most common wind turbine deployed in the region) that are in good agreement with values derived from operational wind farms. The IAV of annual mean wind speeds at/near to typical wind turbine hub-heights in these simulations is lower than is implied by assuming a standard deviation of 6 %. Indeed, rather than in 9 in 10 years exhibiting AEP within 0.9 and 1.1 times the long-term mean AEP, results presented herein indicate that over 90 % of the area in the eastern USA that currently has operating wind turbines simulated AEP lies within 0.94 and 1.06 of the long-term average. Further, IAV of estimated AEP is not substantially larger than IAV in mean wind speeds. These results indicate it may be appropriate to reduce the IAV applied to pre-construction AEP estimates to account for variability in wind climates, which would decrease the cost of capital for wind farm developments.

scholarly journals Value-Centric Approaches to Design, Operations, and Maintenance of Wind Turbines

2013 ◽  
Author(s):  
Madhur A. Khadabadi ◽  
Karen B. Marais
Keyword(s):  
Wind Turbine ◽  
Condition Monitoring ◽  
Wind Farm ◽  
Net Present Value ◽  
Operating Cost ◽  
Optimal Level ◽  
Two Dimensions ◽  
Alternative View ◽  
Operations And Maintenance ◽  
Farm Operators

Wind turbine maintenance is emerging as an unexpectedly high component of turbine operating cost and there is an increasing interest in managing this cost. Here, we present an alternative view of maintenance as a value-driver, and develop an optimization algorithm to maximize the value delivered by maintenance. We model the stochastic deterioration of the turbine in two dimensions: the deterioration rate, and the extent of deterioration, and view maintenance as an operator that moves the turbine to an improved state in which it can generate more power and so earn more revenue. We then use a standard net present value (NPV) approach to calculate the value of the turbine by deducting the costs incurred in the installation, operations and maintenance from the revenue due to the power generation. The application of our model is demonstrated using several scenarios with a focus on blade deterioration. We evaluate the value delivered by implementing blade condition monitoring systems (CMS). A higher fidelity CMS allows the blade state to be determined with higher precision. With this improved state information, an optimal maintenance strategy can be derived. The difference between the value of the turbine with and without CMS can be interpreted as the value of the CMS. The results indicate that a higher fidelity (and more expensive) condition monitoring system (CMS) does not necessarily yield the highest value, and, that there is an optimal level of fidelity that results in maximum value. The contributions of this work are twofold. First, it is a practical approach to wind turbine valuation and operation that takes operating and market conditions into account. This work should therefore be useful to wind farm operators and investors. Second, it shows how the value of a CMS can be explicitly assessed. This work should therefore be useful to CMS manufacturers and wind farm operators.

scholarly journals Optimization of Wind Turbine Interconnections in an Offshore Wind Farm Using Metaheuristic Algorithms

2020 ◽  
Vol 12 (14) ◽  
pp. 5761 ◽  
Author(s):  
Chakib El Mokhi ◽  
Adnane Addaim
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Wind Farm ◽  
Renewable Energy Sources ◽  
Wind Farms ◽  
Optimization Methods ◽  
Network Routing ◽  
Metaheuristic Algorithms ◽  
Offshore Wind ◽  
Offshore Wind Farms

Wind energy is currently one of the fastest-growing renewable energy sources in the world. For this reason, research on methods to render wind farms more energy efficient is reasonable. The optimization of wind turbine positions within wind farms makes the exploitation of wind energy more efficient and the wind farms more competitive with other energy resources. The investment costs alone for substation and electrical infrastructure for offshore wind farms run around 15–30% of the total investment costs of the project, which are considered high. Optimizing the substation location can reduce these costs, which also minimizes the overall cable length within the wind farm. In parallel, optimizing the cable routing can provide an additional benefit by finding the optimal grid network routing. In this article, the authors show the procedure on how to create an optimized wind farm already in the design phase using metaheuristic algorithms. Besides the optimization of wind turbine positions for more energy efficiency, the optimization methods of the substation location and the cable routing for the collector system to avoid cable losses are also presented.

Wind resource assessment and wind farm modeling in Mossobo-Harena area, North Ethiopia

2020 ◽  
pp. 0309524X2092540
Author(s):  
Addisu Dagne Zegeye
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Power Density ◽  
Energy Production ◽  
Wind Farm ◽  
Ground Level ◽  
Energy Potential ◽  
Mean Power ◽  
Wind Energy Potential

Although Ethiopia does not have significant fossil fuel resource, it is endowed with a huge amount of renewable energy resources such as hydro, wind, geothermal, and solar power. However, only a small portion of these resources has been utilized so far and less than 30% of the nation’s population has access to electricity. The wind energy potential of the country is estimated to be up to 10 GW. Yet less than 5% of this potential is developed so far. One of the reasons for this low utilization of wind energy in Ethiopia is the absence of a reliable and accurate wind atlas and resource maps. Development of reliable and accurate wind atlas and resource maps helps to identify candidate sites for wind energy applications and facilitates the planning and implementation of wind energy projects. The main purpose of this research is to assess the wind energy potential and model wind farm in the Mossobo-Harena site of North Ethiopia. In this research, wind data collected for 2 years from Mossobo-Harena site meteorological station were analyzed using different statistical software to evaluate the wind energy potential of the area. Average wind speed and power density, distribution of the wind, prevailing direction, turbulence intensity, and wind shear profile of the site were determined. Wind Atlas Analysis and Application Program was used to generate the generalized wind climate of the area and develop resource maps. Wind farm layout and preliminary turbine micro-sitting were done by taking various factors into consideration. The IEC wind turbine class of the site was determined and an appropriate wind turbine for the study area wind climate was selected and the net annual energy production and capacity factor of the wind farm were determined. The measured data analysis conducted indicates that the mean wind speed at 10 and 40 m above the ground level is 5.12 and 6.41 m/s, respectively, at measuring site. The measuring site’s mean power density was determined to be 138.55 and 276.52 W/m2 at 10 and 40 m above the ground level, respectively. The prevailing wind direction in the site is from east to south east where about 60% of the wind was recorded. The resource grid maps developed by Wind Atlas Analysis and Application Program on a 10 km × 10 km area at 50 m above the ground level indicate that the selected study area has a mean wind speed of 5.58 m/s and a mean power density of 146 W/m2. The average turbulence intensity of the site was found to be 0.136 at 40 m which indicates that the site has a moderate turbulence level. According to the resource assessment done, the area is classified as a wind Class IIIB site. A 2-MW rated power ENERCON E-82 E2 wind turbine which is an IEC Class IIB turbine with 82 m rotor diameter and 98 m hub height was selected for estimation of annual energy production on the proposed wind farm. 88 ENERCON E-82 E2 wind turbines were properly sited in the wind farm with recommended spacing between the turbines so as to reduce the wake loss. The rated power of the wind farm is 180.4 MW and the net annual energy production and capacity factor of the proposed wind farm were determined to be 434.315 GWh and 27.48% after considering various losses in the wind farm.

Condition Monitoring of Wind Turbine Drivetrain Bearings

2019 ◽  
Author(s):  
Konstantinos Gryllias ◽  
Junyu Qi ◽  
Alexandre Mauricio ◽  
Chenyu Liu
Keyword(s):  
Wind Energy ◽  
Condition Monitoring ◽  
Wind Turbines ◽  
Wind Farm ◽  
The Other ◽  
Offshore Wind ◽  
Center Frequency ◽  
Classical Statistic ◽  
Offshore Wind Turbines ◽  
Other Hand

Abstract The current pace of renewable energy development around the world is unprecedented, with offshore wind in particular proving to be an extremely valuable and reliable energy source. The global installed capacity of offshore wind turbines by the end of 2022 is expected to reach the 46.4 GW, among which 33.9 GW in Europe. Costs are critical for the future success of the offshore wind sector. The industry is pushing hard to make cost reductions to show that offshore wind is economically comparable to conventional fossil fuels. Efficiencies in Operations and Maintenance (O&M) offer potential to achieve significant cost savings as it accounts for around 20%–30% of overall offshore wind farm costs. One of the most critical and rather complex assembly of onshore, offshore and floating wind turbines is the gearbox. Gearboxes are designed to last till the end of the lifetime of the asset, according to the IEC 61400-4 standards. On the other hand, a recent study over approximately 350 offshore wind turbines indicate that gearboxes might have to be replaced as early as 6.5 years. Therefore sensing and condition monitoring systems for onshore, offshore and floating wind turbines are needed in order to obtain reliable information on the state and condition of different critical parts, focusing towards the detection and/or prediction of damage before it reaches a critical stage. The development and use of such technologies will allow companies to schedule actions at the right time, and thus will help reducing the costs of operation and maintenance, resulting in an increase of wind energy at a competitive price and thus strengthening productivity of the wind energy sector. At the academic level a plethora of methodologies have been proposed during the last decades for the analysis of vibration signatures focusing towards early and accurate fault detection with limited false alarms and missed detections. Among others, Envelope Analysis is one of the most important methodologies, where an envelope of the vibration signal is estimated, usually after filtering around a selected frequency band excited by impacts due to the faults. Different tools, such as Kurtogram, have been proposed in order to accurately select the optimum filter parameters (center frequency and bandwidth). Cyclostationary Analysis and corresponding methodologies, i.e. the Cyclic Spectral Correlation and the Cyclic Spectral Coherence, have been proved as powerful tools for condition monitoring. On the other hand the application, test and evaluation of such tools on general industrial cases is still rather limited. Therefore the main aim of this paper is the application and evaluation of advanced diagnostic techniques and diagnostic indicators, including the Enhanced Envelope Spectrum and the Spectral Flatness on real world vibration data collected from vibration sensors on gearboxes in multiple wind turbines over an extended period of time of nearly four years. The diagnostic indicators are compared with classical statistic time and frequency indicators, i.e. Kurtosis, Crest Factor etc. and their effectiveness is evaluated based on the successful detection of two failure events.

scholarly journals Comparison of Different Driving Modes for the Wind Turbine Wake in Wind Tunnels

Energies ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1915
Author(s):  
Bingzheng Dou ◽  
Zhanpei Yang ◽  
Michele Guala ◽  
Timing Qu ◽  
Liping Lei ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Farm ◽  
Relevant Information ◽  
Operating Conditions ◽  
Wind Tunnels ◽  
Driving Mode ◽  
Significant Difference ◽  
The Mean ◽  
Turbine Wake

The wake of upstream wind turbine is known to affect the operation of downstream turbines and the overall efficiency of the wind farm. Wind tunnel experiments provide relevant information for understanding and modeling the wake and its dependency on the turbine operating conditions. There are always two main driving modes to operate turbines in a wake experiment: (1) the turbine rotor is driven and controlled by a motor, defined active driving mode; (2) the rotor is driven by the incoming wind and subject to a drag torque, defined passive driving mode. The effect of the varying driving mode on the turbine wake is explored in this study. The mean wake velocities, turbulence intensities, skewness and kurtosis of the velocity time-series estimated from hot-wire anemometry data, were obtained at various downstream locations, in a uniform incoming flow wind tunnel and in an atmospheric boundary layer wind tunnel. The results show that there is not a significant difference in the mean wake velocity between these two driving modes. An acceptable agreement is observed in the comparison of wake turbulence intensity and higher-order statistics in the two wind tunnels.

scholarly journals Wake and Turbulence Analysis for Wind Turbine Layouts in an Island

2018 ◽  
Vol 64 ◽  
pp. 06010
Author(s):  
Bachhal Amrender Singh ◽  
Vogstad Klaus ◽  
Lal Kolhe Mohan ◽  
Chougule Abhijit ◽  
Beyer Hans George
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Production ◽  
Wind Farm ◽  
Full Length Paper ◽  
Turbulence Analysis ◽  
Wake Model ◽  
Wind Resources

There is a big wind energy potential in supplying the power in an island and most of the islands are off-grid. Due to the limited area in island(s), there is need to find appropriate layout / location for wind turbines suited to the local wind conditions. In this paper, we have considered the wind resources data of an island in Trøndelag region of the Northern Norway, situated on the coastal line. The wind resources data of this island have been analysed for wake losses and turbulence on wind turbines for determining appropriate locations of wind turbines in this island. These analyses are very important for understanding the fatigue and mechanical stress on the wind turbines. In this work, semi empirical wake model has been used for wake losses analysis with wind speed and turbine spacings. The Jensen wake model used for the wake loss analysis due to its high degree of accuracy and the Frandsen model for characterizing the turbulent loading. The variations of the losses in the wind energy production of the down-wind turbine relative to the up-wind turbine and, the down-stream turbulence have been analysed for various turbine distances. The special emphasis has been taken for the case of wind turbine spacing, leading to the turbulence conditions for satisfying the IEC 61400-1 conditions to find the wind turbine layout in this island. The energy production of down-wind turbines has been decreased from 2 to 20% due to the lower wind speeds as they are located behind up-wind turbine, resulting in decreasing the overall energy production of the wind farm. Also, the higher wake losses have contributed to the effective turbulence, which has reduced the overall energy production from the wind farm. In this case study, the required distance for wind turbines have been changed to 6 rotor diameters for increasing the energy gain. From the results, it has been estimated that the marginal change in wake losses by moving the down-stream wind turbine by one rotor diameter distance has been in the range of 0.5 to 1% only and it is insignificant. In the full-length paper, the wake effects with wind speed variations and the wind turbine locations will be reported for reducing the wake losses on the down-stream wind turbine. The Frandsen model has been used for analysing turbulence loading on the down-stream wind turbine as per IEC 61400-1 criteria. In larger wind farms, the high turbulence from the up-stream wind turbines increases the fatigues on the turbines of the wind farm. In this work, we have used the effective turbulence criteria at a certain distance between up-stream and down-stream turbines for minimizing the fatigue load level. The sensitivity analysis on wake and turbulence analysis will be reported in the full-length paper. Results from this work will be useful for finding wind farm layouts in an island for utilizing effectively the wind energy resources and electrification using wind power plants.

Wind Flow Over a Complex Terrain in Nygårdsfjell, Norway

2015 ◽  
Author(s):  
Muhammad Bilal ◽  
Narendran Sridhar ◽  
Guillermo Araya ◽  
Sivapathas Parameswaran ◽  
Yngve Birkelund
Keyword(s):  
Wind Energy ◽  
Wind Turbine ◽  
Complex Terrain ◽  
Wind Farm ◽  
Turbulence Models ◽  
Future Research ◽  
Wind Flow ◽  
Governing Equations ◽  
The North ◽  
Numerical Predictions

The understanding of atmospheric flows is crucial in the analysis of dispersion of a contaminant or pollutant, wind energy and air-quality assessment to name a few. Additionally, the effects of complex terrain and associated orographic forcing are crucial in wind energy production. Furthermore, the use of the Reynolds-averaged Navier-Stokes (RANS) equations in the analysis of complex terrain is still considered the “workhorse” since millions of mesh points are required to accurately capture the details of the surface. On the other hand, solving the same problem by means of the instantaneous governing equations of the flow (i.e., in a suite of DNS or LES) would imply almost prohibitive computational resources. In this study, numerical predictions of atmospheric boundary layers are performed over a complex topography located in Nygårdsfjell, Norway. The Nygårdsfjell wind farm is located in a valley at approximately 420 meters above sea level surrounded by mountains in the north and south near the Swedish border. Majority of the winds are believed to be originated from Torneträsk lake in the east which is covered with ice during the winter time. The air closest to the surface on surrounding mountains gets colder and denser. The air then slides down the hill and accumulates over the lake. Later, the air spills out westward towards Ofotfjord through the broader channel that directs and transforms it into highly accelerated winds. Consequently, one of the objectives of the present article is to study the influence of local terrain on shaping these winds over the wind farm. It is worth mentioning that we are not considering any wind turbine model in the present investigation, being the main purpose to understand the influence of the local surface topography and roughness on the wind flow. Nevertheless, future research will include modeling the presence of a wind turbine and will be published elsewhere. The governing equations of the flow are solved by using a RANS approach and by considering three different two-equation turbulence models: k-omega (k–ω), k-epsilon (k–ε) and shear stress transport (SST). Furthermore, the real topographical characteristics of the terrain have been modeled by extracting the required area from the larger digital elevation model (DEM) spanning over 100 km square. The geometry is then extruded using Rhino and meshed in ANSYS Fluent. The terrain dimensions are approximately 2000×1000 meter square.

scholarly journals Wake behavior and control: comparison of LES simulations and wind tunnel measurements

2019 ◽  
Vol 4 (1) ◽  
pp. 71-88 ◽  
Author(s):  
Jiangang Wang ◽  
Chengyu Wang ◽  
Filippo Campagnolo ◽  
Carlo L. Bottasso
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Wind Farm ◽  
Operating Conditions ◽  
Test Cases ◽  
Near Wake ◽  
Large Eddy ◽  
Control Comparison ◽  
High Turbulence ◽  
And Control

Abstract. This paper applies a large-eddy actuator line approach to the simulation of wind turbine wakes. In addition to normal operating conditions, a specific focus of the paper is on wake manipulation, which is performed here by derating, yaw misalignment and cyclic pitching of the blades. With the purpose of clarifying the ability of LES methods to represent conditions that are relevant for wind farm control, numerical simulations are compared to experimental observations obtained in a boundary layer wind tunnel with scaled wind turbine models. Results indicate a good overall matching of simulations with experiments. Low-turbulence test cases appear to be more challenging than moderate- and high-turbulence ones due to the need for denser grids to limit numerical diffusion and accurately resolve tip-shed vortices in the near-wake region.

Sign in / Sign up

Export Citation Format

Share Document