Correlation of Piping System Detonation Test Data and System Analyses

2012 ◽  
Author(s):  
Thomas C. Ligon ◽  
David J. Gross ◽  
John C. Minichiello
Keyword(s):  
Finite Element ◽  
Test Data ◽  
Flow Direction ◽  
Element Model ◽  
Beam Element ◽  
Piping System ◽  
Finite Element Models ◽  
Detonation Pressure ◽  
Reaction Products ◽  
Axial Forces

This paper describes hydrogen and nitrous oxide detonation experiments that were performed using an approximately 200-ft long 2-inch schedule 40 piping system. The objective of these experiments was to develop an understanding of the loads and forces imposed by internal detonation on piping combinations representative of a typical industrial piping system. The apparatus contained numerous straight pipe lengths with 90° and 45° bends, 90° elbows, and a tee along with rigid foundation supports that were connected to the pipe using typical u-bolt fasteners. As a detonation wave propagates through a gas-filled piping system, the pipe begins to respond globally once a detonation encounters a change in flow direction, such as a bend, causing a pressure imbalance due to both the internal detonation pressure and change in momentum of the reaction products. The resultant force imparts both axial forces and moments on the pipe exciting both extensional and bending modes. The test data was used to validate two finite element (FE) models developed using the ANSYS finite-element program: a hybrid model that made use of both shell and beam elements, to determine the interaction between shell and beam modes, and an all beam element model. An additional beam element model was developed using the Bechtel National Inc. software ME101 that was also found to be in agreement with the measured and ANSYS calculated frequencies and support loads. In addition to the detonation testing, the finite-element models were validated against experimental modal analysis data of the piping system that identified the primary modal frequencies and vectors. These data were compared to the modes extracted from finite-element models of the piping system.

Contrastive Study on Finite Element Models of High-Strength Pipelines Crossing Active Faults

2016 ◽  
Vol 850 ◽  
pp. 957-964
Author(s):  
Wei Zheng ◽  
Hong Zhang ◽  
Xiao Ben Liu ◽  
Le Cai Liang ◽  
Yin Shan Han
Keyword(s):  
Finite Element ◽  
Design Method ◽  
Active Faults ◽  
Shell Element ◽  
High Strength ◽  
Element Model ◽  
Beam Element ◽  
Finite Element Models ◽  
Fixed Boundary ◽  
Equivalent Boundary

There is a potential for major damage to the pipelines crossing faults, therefore the strain-based design method is essential for the design of buried pipelines. Finite element models based on soil springs which are able to accurately predict pipelines’ responses to such faulting are recommended by some international guidelines. In this paper, a comparative analysis was carried out among four widely used models (beam element model; shell element model with fixed boundary; shell element model with beam coupled; shell element model with equivalent boundary) in two aspects: differences of results and the efficiency of calculation. The results show that the maximum and minimum strains of models coincided with each other under allowable strain and the calculation efficiency of beam element model was the highest. Besides, the shell element model with beam coupled or equivalent boundary provided the reasonable results and the calculation efficiency of them were higher than the one with fixed boundary. In addition, shell element model with beam coupled had a broader applicability.

scholarly journals Biaxial estimation of biomechanical constitutive parameters of passive porcine sclera soft tissue

2021 ◽  
Author(s):  
Zwelihle Ndlovu ◽  
Dawood Desai ◽  
Thanyani Pandelani ◽  
Harry Ngwangwa ◽  
Fulufhelo Nemavhola
Keyword(s):  
Finite Element ◽  
Soft Tissue ◽  
Finite Element Model ◽  
Test Data ◽  
Element Model ◽  
Finite Element Models ◽  
Anisotropic Model ◽  
Material Models ◽  
Material Parameters ◽  
Constitutive Parameters

This study assesses the modelling capabilities of four constitutive hyperplastic material models to fit the experimental data of the porcine sclera soft tissue. It further estimates the material parameters and discusses their applicability to a finite element model by examining the statistical dispersion measured through the standard deviation. Fifteen sclera tissues were harvested from porcine’ slaughtered at an abattoir and were subjected to equi-biaxial testing. The results show that all the four material models yielded very good correlations at correlations above 96 %. The polynomial (anisotropic) model gave the best correlation of 98 %. However, the estimated material parameters varied widely from one test to another such that there would be needed to normalise the test data to avoid long optimisation processes after applying the average material parameters to finite element models. However, for application of the estimated material parameters to finite element models, there would be needed to consider normalising the test data to reduce the search region for the optimisation algorithms. Although the polynomial (anisotropic) model yielded the best correlation, it was found that the Choi-Vito had the least variation in the estimated material parameters thereby making it an easier option for application of its material parameters to a finite element model and also requiring minimum effort in the optimisation procedure. For the porcine sclera tissue, it was found that the anisotropy more influenced by the fiber-related properties than the background material matrix related properties.

Finite element bending analysis of symmetric and non-symmetric functionally graded sandwich beams using a novel parabolic shear deformation theory

2021 ◽  
pp. 146442072110050
Author(s):  
Mohamed-Ouejdi Belarbi ◽  
Abdelhak Khechai ◽  
Aicha Bessaim ◽  
Mohammed-Sid-Ahmed Houari ◽  
Aman Garg ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Shear Deformation ◽  
Transverse Shear ◽  
Deformation Theory ◽  
Shear Deformation Theory ◽  
Element Model ◽  
Beam Element ◽  
Functionally Graded ◽  
Sandwich Beams

In this paper, the bending behavior of functionally graded single-layered, symmetric and non-symmetric sandwich beams is investigated according to a new higher order shear deformation theory. Based on this theory, a novel parabolic shear deformation function is developed and applied to investigate the bending response of sandwich beams with homogeneous hardcore and softcore. The present theory provides an accurate parabolic distribution of transverse shear stress across the thickness and satisfies the zero traction boundary conditions on the top and bottom surfaces of the functionally graded sandwich beam without using any shear correction factors. The governing equations derived herein are solved by employing the finite element method using a two-node beam element, developed for this purpose. The material properties of functionally graded sandwich beams are graded through the thickness according to the power-law distribution. The predictive capability of the proposed finite element model is demonstrated through illustrative examples. Four types of beam support, i.e. simply-simply, clamped-free, clamped–clamped, and clamped-simply, are used to study how the beam deflection and both axial and transverse shear stresses are affected by the variation of volume fraction index and beam length-to-height ratio. Results of the numerical analysis have been reported and compared with those available in the open literature to evaluate the accuracy and robustness of the proposed finite element model. The comparisons with other higher order shear deformation theories verify that the proposed beam element is accurate, presents fast rate of convergence to the reference results and it is also valid for both thin and thick functionally graded sandwich beams. Further, some new results are reported in the current study, which will serve as a benchmark for future research.

Updating Finite Element Model of Combined Structures on the Basis of Dynamic Test Results

1996 ◽  
Author(s):  
Chen Xin ◽  
Qin Ye ◽  
Yuan Xiguang ◽  
Zhang Ping ◽  
Sun Jian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Test Data ◽  
Dynamic Test ◽  
Element Model ◽  
Physical Parameters ◽  
Structural Joint ◽  
Combined Structure ◽  
Joint Parameters ◽  
Two Stages

Abstract According to the real situation, a new method of updating the finite element model (FEM) of a combined structure step by step is proposed in this paper. It is assumed that there are two types of error when establishing the FEMs. One of them results from the simplifications, in fact, it is severe for complicated structures, which usually assume many simplifications; the other is from the process of identifying structural joint parameters. For this reason, it is recommended that the FEM should be established in two stages. At the first stage, the local physical parameters relating with the simplifications are corrected by using the dynamic test data of the corresponding substructures. Then, the structural joint parameters that link the substructures are corrected by the dynamic test data of the combined structure as a whole. The updating formula is presented and proved, and its algorithm is also described. And the experimental results show that the efficiency and accuracy of the proposed method are quite satisfactory.

Behavior of Structures Using Simple Plastic Hinge Theory

1994 ◽  
Author(s):  
Ramakrishnan Maruthayappan ◽  
Hamid M. Lankarani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cantilever Beam ◽  
Reliable Method ◽  
Plastic Hinge ◽  
Element Model ◽  
Finite Element Models ◽  
Computational Program ◽  
Hinge Model ◽  
The Impact

Abstract The behavior of structures under the impact or crash situations demands an efficient modeling of the system for its behavior to be predicted close to practical situations. The various formulations that are possible to model such systems are spring mass models, finite element models and plastic hinge models. Of these three techniques, the plastic hinge theory offers a more accurate model compared to the spring mass formulation and is much simpler than the finite element models. Therefore, it is desired to model the structure using plastic hinges and to use a computational program to predict the behavior of structures. In this paper, the behavior of some simple structures, ranging from an elementary cantilever beam to a torque box are predicted. It is also shown that the plastic hinge theory is a reliable method by comparing the results obtained from a plastic hinge model of an aviation seat structure with that obtained from a finite element model.

Calculating Mechanics Characteristics of Single-Walled Carbon Nanotube Materials by Finite Element Method

2017 ◽  
Vol 730 ◽  
pp. 548-553
Author(s):  
Jing Ge ◽  
Hao Jiang ◽  
Zhen Yu Sun ◽  
Guo Jun Yu ◽  
Bo Su ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Radial Direction ◽  
Element Model ◽  
Beam Element ◽  
Beam Position ◽  
Single Walled Carbon ◽  
Finite Element Software ◽  
Calculation Results ◽  
The Moment

In this paper, we establish the mechanical property analysis of Single-walled Carbon Nanotubes (SWCNTs) modified beam element model based on the molecular structural mechanics method. Then we study the mechanical properties of their radial direction characteristics using the finite element software Abaqus. The model simulated the different bending stiffness with rectangular section beam elements C-C chemical force field. When the graphene curled into arbitrary chirality of SWCNTs spatial structure, the adjacent beam position will change the moment of inertia of the section of the beam. Compared with the original beam element model and the calculation results, we found that the established model largely reduced the overestimate of the original model of mechanical properties on the radial direction of the SWCNTs. At the same time, compared with other methods available in the literature results and the experimental data, the results can be in good agreement.

scholarly journals Aspects of Uncertainty Analysis for Large Nonlinear Computational Models

2010 ◽  
Vol 24-25 ◽  
pp. 25-41 ◽  
Author(s):  
Keith Worden ◽  
W.E. Becker ◽  
Manuela Battipede ◽  
Cecilia Surace
Keyword(s):  
Finite Element ◽  
Monte Carlo ◽  
Computational Models ◽  
Element Model ◽  
Finite Element Models ◽  
Bayesian Algorithm ◽  
Basic Principles ◽  
Structure Interaction ◽  
Output Uncertainty ◽  
Input Uncertainties

This paper concerns the analysis of how uncertainty propagates through large computational models like finite element models. If a model is expensive to run, a Monte Carlo approach based on sampling over the possible model inputs will not be feasible, because the large number of model runs will be prohibitively expensive. Fortunately, an alternative to Monte Carlo is available in the form of the established Bayesian algorithm discussed here; this algorithm can provide information about uncertainty with many less model runs than Monte Carlo requires. The algorithm also provides information regarding sensitivity to the inputs i.e. the extent to which input uncertainties are responsible for output uncertainty. After describing the basic principles of the Bayesian approach, it is illustrated via two case studies: the first concerns a finite element model of a human heart valve and the second, an airship model incorporating fluid structure interaction.

scholarly journals Reconstruction finite element model of cars

2021 ◽  
Vol 4 (1) ◽  
pp. first
Author(s):  
Lý Hùng Anh ◽  
Nguyễn Phụ Thượng Lưu ◽  
Nguyễn Thiên Phú ◽  
Trần Đình Nhật
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Finite Element Models ◽  
Crash Analysis ◽  
Inertia Moment ◽  
Frontal Crash ◽  
Analysis Center ◽  
Simulation Results ◽  
And Behavior

The experimental method used in a frontal crash of cars costs much time and expense. Therefore, numerical simulation in crashworthiness is widely applied in the world. The completed car models contain a lot of parts which provided complicated structure, especially the rear of car models do not contribute to behavior of frontal crash which usually evaluates injuries of pedestrian or motorcyclist. In order to save time and resources, a simplification of the car models for research simulations is essential with the goal of reducing approximately 50% of car model elements and nodes. This study aims to construct the finite element models of front structures of vehicle based on the original finite element models. Those new car models must be maintained important values such as mass and center of gravity position. By using condition boundaries, inertia moment is kept unchanged on new model. The original car models, which are provided by the National Crash Analysis Center (NCAC), validated by using results from experimental crash tests. The modified (simplistic) vehicle FE models are validated by comparing simulation results with experimental data and simulation results of the original vehicle finite element models. LS-Dyna software provides convenient tools and very strong to modify finite element model. There are six car models reconstructed in this research, including 1 Pick-up, 2 SUV and 3 Sedan. Because car models were not the main object to evaluate in a crash, energy and behavior of frontal part have the most important role. As a result, six simplified car models gave reasonable outcomes and reduced significantly the number of nodes and elements. Therefore, the simulation time is also reduced a lot. Simplified car models can be applied to the upcoming frontal simulations.

Sign in / Sign up

Export Citation Format

Share Document