scholarly journals Reconstruction finite element model of cars

2021 ◽  
Vol 4 (1) ◽  
pp. first
Author(s):  
Lý Hùng Anh ◽  
Nguyễn Phụ Thượng Lưu ◽  
Nguyễn Thiên Phú ◽  
Trần Đình Nhật
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Finite Element Models ◽  
Crash Analysis ◽  
Inertia Moment ◽  
Frontal Crash ◽  
Analysis Center ◽  
Simulation Results ◽  
And Behavior

The experimental method used in a frontal crash of cars costs much time and expense. Therefore, numerical simulation in crashworthiness is widely applied in the world. The completed car models contain a lot of parts which provided complicated structure, especially the rear of car models do not contribute to behavior of frontal crash which usually evaluates injuries of pedestrian or motorcyclist. In order to save time and resources, a simplification of the car models for research simulations is essential with the goal of reducing approximately 50% of car model elements and nodes. This study aims to construct the finite element models of front structures of vehicle based on the original finite element models. Those new car models must be maintained important values such as mass and center of gravity position. By using condition boundaries, inertia moment is kept unchanged on new model. The original car models, which are provided by the National Crash Analysis Center (NCAC), validated by using results from experimental crash tests. The modified (simplistic) vehicle FE models are validated by comparing simulation results with experimental data and simulation results of the original vehicle finite element models. LS-Dyna software provides convenient tools and very strong to modify finite element model. There are six car models reconstructed in this research, including 1 Pick-up, 2 SUV and 3 Sedan. Because car models were not the main object to evaluate in a crash, energy and behavior of frontal part have the most important role. As a result, six simplified car models gave reasonable outcomes and reduced significantly the number of nodes and elements. Therefore, the simulation time is also reduced a lot. Simplified car models can be applied to the upcoming frontal simulations.

The Influence of the Curved Transition on the Coach Roof Cross Beams in Rollover Crashworthiness

2011 ◽  
Vol 474-476 ◽  
pp. 1920-1925
Author(s):  
Fu Lin Shen ◽  
Jun Liang Jiu ◽  
Zhao Kai Li ◽  
Xu Liang Xie ◽  
Ying Hui Mao
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Energy Absorption ◽  
Collision Energy ◽  
Element Model ◽  
Finite Element Models ◽  
Complete Vehicle ◽  
Simulation Results ◽  
Survival Space ◽  
Peak Value

In order to improve the rollover crashworthiness of coach, three roof beam structures commonly used in coach were established with finite element models for the rollover simulation, then the energy absorption, acceleration and body pillar deformation were analyzed. The simulation results show that circle-curved transition and non-curved transition on the roof have better collision performance. Especially, the latter not only reduces the acceleration peak value, but also transfers more collision energy to the offside lateral. The whole coach body will be involved in deformation, thus, the intrusion of survival space would be reduced. Finally, the complete vehicle skeleton finite element model of a 6127-type high-bed coach was built, and the influences of circle-curved transition and non-curved transition on the roof in rollover test were analyzed.

scholarly journals Investigation of the Thickness Differential on the Formability of Aluminum Tailor Welded Blanks

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 875
Author(s):  
Jie Wu ◽  
Yuri Hovanski ◽  
Michael Miles
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Numerical Model ◽  
Plastic Strain ◽  
Finite Element Model ◽  
Equivalent Plastic Strain ◽  
Element Model ◽  
Dome Height ◽  
Tailor Welded Blanks ◽  
Simulation Results

A finite element model is proposed to investigate the effect of thickness differential on Limiting Dome Height (LDH) testing of aluminum tailor-welded blanks. The numerical model is validated via comparison of the equivalent plastic strain and displacement distribution between the simulation results and the experimental data. The normalized equivalent plastic strain and normalized LDH values are proposed as a means of quantifying the influence of thickness differential for a variety of different ratios. Increasing thickness differential was found to decrease the normalized equivalent plastic strain and normalized LDH values, this providing an evaluation of blank formability.

Behavior of Structures Using Simple Plastic Hinge Theory

1994 ◽  
Author(s):  
Ramakrishnan Maruthayappan ◽  
Hamid M. Lankarani
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Cantilever Beam ◽  
Reliable Method ◽  
Plastic Hinge ◽  
Element Model ◽  
Finite Element Models ◽  
Computational Program ◽  
Hinge Model ◽  
The Impact

Abstract The behavior of structures under the impact or crash situations demands an efficient modeling of the system for its behavior to be predicted close to practical situations. The various formulations that are possible to model such systems are spring mass models, finite element models and plastic hinge models. Of these three techniques, the plastic hinge theory offers a more accurate model compared to the spring mass formulation and is much simpler than the finite element models. Therefore, it is desired to model the structure using plastic hinges and to use a computational program to predict the behavior of structures. In this paper, the behavior of some simple structures, ranging from an elementary cantilever beam to a torque box are predicted. It is also shown that the plastic hinge theory is a reliable method by comparing the results obtained from a plastic hinge model of an aviation seat structure with that obtained from a finite element model.

scholarly journals Biaxial estimation of biomechanical constitutive parameters of passive porcine sclera soft tissue

2021 ◽  
Author(s):  
Zwelihle Ndlovu ◽  
Dawood Desai ◽  
Thanyani Pandelani ◽  
Harry Ngwangwa ◽  
Fulufhelo Nemavhola
Keyword(s):  
Finite Element ◽  
Soft Tissue ◽  
Finite Element Model ◽  
Test Data ◽  
Element Model ◽  
Finite Element Models ◽  
Anisotropic Model ◽  
Material Models ◽  
Material Parameters ◽  
Constitutive Parameters

This study assesses the modelling capabilities of four constitutive hyperplastic material models to fit the experimental data of the porcine sclera soft tissue. It further estimates the material parameters and discusses their applicability to a finite element model by examining the statistical dispersion measured through the standard deviation. Fifteen sclera tissues were harvested from porcine’ slaughtered at an abattoir and were subjected to equi-biaxial testing. The results show that all the four material models yielded very good correlations at correlations above 96 %. The polynomial (anisotropic) model gave the best correlation of 98 %. However, the estimated material parameters varied widely from one test to another such that there would be needed to normalise the test data to avoid long optimisation processes after applying the average material parameters to finite element models. However, for application of the estimated material parameters to finite element models, there would be needed to consider normalising the test data to reduce the search region for the optimisation algorithms. Although the polynomial (anisotropic) model yielded the best correlation, it was found that the Choi-Vito had the least variation in the estimated material parameters thereby making it an easier option for application of its material parameters to a finite element model and also requiring minimum effort in the optimisation procedure. For the porcine sclera tissue, it was found that the anisotropy more influenced by the fiber-related properties than the background material matrix related properties.

Application of a FRF Based Model Updating Technique for the Validation of Finite Element Models of Components of the Automotive Industry

1995 ◽  
Author(s):  
Stefan Lammens ◽  
Marc Brughmans ◽  
Jan Leuridan ◽  
Ward Heylen ◽  
Paul Sas
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Automotive Industry ◽  
Stiffness Matrix ◽  
Model Updating ◽  
Dynamic Stiffness ◽  
Element Model ◽  
Model Parameters ◽  
Finite Element Models ◽  
Analytical Dynamic

Abstract This paper presents two applications of the RADSER model updating technique (Lammens et al. (1995) and Larsson (1992)). The RADSER technique updates finite element model parameters by solution of a linearised set of equations that optimise the Reduced Analytical Dynamic Stiffness matrix based on Experimental Receptances. The first application deals with the identification of the dynamic characteristics of rubber mounts. The second application validates a coarse finite element model of a subframe of a Volvo 480.

ESTABLISHMENT AND APPLICATION OF LOWER LIMB FINITE ELEMENT MODEL BASED ON MUSCLE GROUPS

2018 ◽  
Vol 18 (08) ◽  
pp. 1840024
Author(s):  
MONAN WANG ◽  
RONGPENG LI ◽  
JUNTONG JING
Keyword(s):  
Experimental Study ◽  
Finite Element ◽  
Finite Element Model ◽  
Lower Limb ◽  
Element Model ◽  
Upper And Lower Bounds ◽  
Three Point Bending ◽  
Living Body ◽  
Prosthetic Socket ◽  
Simulation Results

Living body or corpse could be replaced with the virtual human tissue model for biomechanical experimental study, which effectively avoids the non-reusability, great social controversy, huge costs and difficulty in extracting parameters, and finally, the accurate analysis results are obtained. Unlike the previous lower limb models, the finite element models of hip and thigh were established based on the concept of muscle group in this paper. The cortical bones of hip bone and femur were set as *MAT_PIECEWISE_LINEAR_ PLASTICITY. The material of cancellous bone was set as *MAT_ELASTIC_PLASTIC_ WITH_DAMAGE_FAILURE. The material of articular cartilage was set as *MAT_ISOTROPIC_ELASTIC. The materials of muscle and fat were set as *MAT_VISCOELASTIC. The accuracy of the finite element model was verified by dynamic three-point bending experiment of the thighs. Mechanical simulation was carried out to the stump-prosthetic socket and the comfort of socks by the established model. The simulation results were all between the upper and lower bounds of the experimental results in the dynamic three-point bending experiment of the thighs where the loads were separately applied to one-third of the distal end of thighs and the middle part of thighs. The simulation results of the stump-prosthetic socket example show that the optimal elastic modulus of silicone pad is 2.5[Formula: see text]MPa. Simulation results of socks comfort show that the distribution of stress and deformation of the anterior and posterior thighs is different when the human lower limbs are in stockings. The established simulation model meets the accuracy requirement and can replace the living body or corpse to carry out biomechanical experimental study. The finite element simulation results converge, and the time to complete a finite element calculation is less than or equal to 10[Formula: see text]min.

Numerical Simulation and Process Research for Cylindrical Drawing

2010 ◽  
Vol 20-23 ◽  
pp. 1405-1408 ◽  
Author(s):  
Wei Hua Kuang ◽  
Qun Liu
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Process Research ◽  
Die Design ◽  
Drawing Process ◽  
3D Finite Element ◽  
Simulation Results ◽  
Distribution Of Stress

Drawing process is an important technology in shaping products. In the paper, the geometric surfaces of tools and sheet were modeled by Pro/E software, and a 3D finite element model of the cylindrical drawing process was developed by DYNAFORM. Numerical simulation results showed the distribution of stress, strain and thickness. FLD showed no material was in crack area and risk crack area. The drawing process could be successfully completed in one stroke. The simulation results were helpful for the die design.

Forming limit diagrams by including the M–K model in finite element simulation considering the effect of bending

2016 ◽  
Vol 232 (8) ◽  
pp. 625-636 ◽  
Author(s):  
Mostafa Habibi ◽  
Ramin Hashemi ◽  
Ahmad Ghazanfari ◽  
Reza Naghdabadi ◽  
Ahmad Assempour
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Metal Forming ◽  
Forming Limit Diagram ◽  
Element Model ◽  
Forming Limit ◽  
Finite Element Models ◽  
Element Simulation ◽  
Simple Tension ◽  
Out Of Plane

Forming limit diagram is often used as a criterion to predict necking initiation in sheet metal forming processes. In this study, the forming limit diagram was obtained through the inclusion of the Marciniak–Kaczynski model in the Nakazima out-of-plane test finite element model and also a flat model. The effect of bending on the forming limit diagram was investigated numerically and experimentally. Data required for this simulation were determined through a simple tension test in three directions. After comparing the results of the flat and Nakazima finite element models with the experimental results, the forming limit diagram computed by the Nakazima finite element model was more convenient with less than 10% at the lower level of the experimental forming limit diagram.

Stress Analysis of Laminated Glass under Uniform Lateral Pressure

2011 ◽  
Vol 418-420 ◽  
pp. 50-54
Author(s):  
Shi Hong Pang ◽  
Juan Rong Ma ◽  
Zhen Zhu Ma ◽  
Li Chuang Wang
Keyword(s):  
Finite Element ◽  
Shear Modulus ◽  
Finite Element Model ◽  
Stress Analysis ◽  
Lateral Pressure ◽  
Element Model ◽  
Maximum Principal Stress ◽  
Laminated Glass ◽  
Load Duration ◽  
Simulation Results

The shear modulus of PVB and SGP interlayer is analyzed. With the same conditions of load duration and temperature, the shear modulus of SGP interlayer is about fifteen times than that of PVB interlayer. A finite element model of laminated glass is established in this paper. The simulation results show that the maximum principal stress contours of PVB laminated glass change from a circular to a petal-shaped one and those of SGP laminated glass change form a quadrangular to a square-shaped one when the temperature rises from 20 degrees Celsius to 50 degrees Celsius.

Sign in / Sign up

Export Citation Format

Share Document