Hydrogen Embrittlement Susceptibility of Clad Steel Pipes

2017 ◽  
Author(s):  
Lise Jemblie ◽  
Vigdis Olden ◽  
Bård Nyhus ◽  
Odd Magne Akselsen
Keyword(s):  
Hydrogen Embrittlement ◽  
Base Material ◽  
Fracture Initiation ◽  
Experimental Investigations ◽  
Initiation Toughness ◽  
Steel Pipes ◽  
Ni Interlayer ◽  
Clad Steel ◽  
Hot Rolled

The objective of the present work has been to evaluate the hydrogen embrittlement susceptibility of 316L - X60/X65 carbon steel hot rolled bonded clad pipes through experimental investigations and cohesive zone numerical simulations. Fracture mechanical testing in air and under in situ electrochemical hydrogen charging revealed little hydrogen influence on the samples with a Ni-interlayer between the clad and the base material, while significant hydrogen influence on the sample without a Ni-interlayer. Cohseive zone simulations were able to predict the detrimental influence of hydrogen on the fracture initiation toughness. The simulations suggest that hydrogen trapped at dislocations are mainly responsible for the embrittlement of the clad pipe base material.

scholarly journals The fracture toughness of martensite islands in dual-phase DP800 steel

2021 ◽  
Author(s):  
Chunhua Tian ◽  
Christoph Kirchlechner
Keyword(s):  
Fracture Toughness ◽  
Fracture Initiation ◽  
Initiation Toughness ◽  
Dual Phase ◽  
Dp Steel ◽  
Bending Tests ◽  
Damage Initiation ◽  
Linear Elastic ◽  
Steel Grades

Abstract In situ microcantilever bending tests were performed on martensite islands in a dual-phase (DP) steel to extract the fracture toughness of martensite at the microscale and to understand damage initiation during forming of DP steels. All microcantilevers were produced through FIB milling. The martensite islands do not exhibit linear elastic brittle fracture; instead, significant ductile tearing is observed. The conditional fracture initiation toughness extracted by definition and by Pippan’s transfer criterion is Ki = 6.5 ± 0.4 MPa m1/2 and Ki,2% = 10.1 ± 0.3 MPa m1/2, respectively. The obtained value is well-represented by the strength-toughness trend of other ferritic steel grades. Considering the yield stress of the same martensite island, we found that crack initiation can occur only in very large martensite islands or in a banded or agglomerated martensite structure. Graphic abstract

Hydraulic Fracturing Process: Roles of In Situ Stress and Rock Strength

2012 ◽  
Vol 616-618 ◽  
pp. 435-440
Author(s):  
Yan Jun Feng ◽  
Xiu Wei Shi
Keyword(s):  
Hydraulic Fracturing ◽  
Analytical Model ◽  
Field Experiments ◽  
Rock Strength ◽  
Fracture Initiation ◽  
In Situ Stress ◽  
Experimental Investigations ◽  
Propagation Process ◽  
Fracturing Process

This paper presents results of a comprehensive study involving analytical and field experimental investigations into the factors controlling the hydraulic fracturing process. Analytical theories for fracture initiation of vertical and horizontal borehole are reviewed. The initiation and propagation process of hydraulic fracturing is performed in the field by means of hydraulic fracturing and stepwise hydraulic fracturing, the effect of factors such as in-situ stress and rock strength on fracture propagation process is studied and discussed. The fracture initiation pressures estimated from the analytical model and field experiments are compared as well as the fracturing process during case 1and case 2. Results from the analytical model and field experiments conducted in this study are interpreted with a particular effort to enlighten the factors controlling the hydraulic fracturing process.

scholarly journals Additive Manufacturing-Based In Situ Consolidation of Continuous Carbon Fibre-Reinforced Polycarbonate

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2450
Author(s):  
Andreas Borowski ◽  
Christian Vogel ◽  
Thomas Behnisch ◽  
Vinzenz Geske ◽  
Maik Gude ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Carbon Fibre ◽  
Bending Test ◽  
Thermoplastic Composites ◽  
Experimental Investigations ◽  
Material Structure ◽  
Three Point Bending ◽  
Continuous Fibre ◽  
Local Material

Continuous carbon fibre-reinforced thermoplastic composites have convincing anisotropic properties, which can be used to strengthen structural components in a local, variable and efficient way. In this study, an additive manufacturing (AM) process is introduced to fabricate in situ consolidated continuous fibre-reinforced polycarbonate. Specimens with three different nozzle temperatures were in situ consolidated and tested in a three-point bending test. Computed tomography (CT) is used for a detailed analysis of the local material structure and resulting material porosity, thus the results can be put into context with process parameters. In addition, a highly curved test structure was fabricated that demonstrates the limits of the process and dependent fibre strand folding behaviours. These experimental investigations present the potential and the challenges of additive manufacturing-based in situ consolidated continuous fibre-reinforced polycarbonate.

Hydrogen-induced amorphization and embrittlement resistance in Ti-based in situ composite with bcc-phase in an amorphous matrix

2007 ◽  
Vol 22 (2) ◽  
pp. 428-436 ◽  
Author(s):  
S. Jayalakshmi ◽  
J.P. Ahn ◽  
K.B. Kim ◽  
E. Fleury
Keyword(s):  
Hydrogen Embrittlement ◽  
Amorphous Alloys ◽  
Amorphous Matrix ◽  
Mechanical Tests ◽  
High Concentration ◽  
High Hydrogen ◽  
In Situ Composite ◽  
Bcc Phase ◽  
Embrittlement Resistance

We report the hydrogenation characteristics and mechanical properties of Ti50Zr25Cu25 in situ composite ribbons, composed of β-Ti crystalline phase dispersed in an amorphous matrix. Upon cathodic charging at room temperature, high hydrogen absorption up to ∼60 at.% (H/M = ∼1.2) is obtained. At such a high concentration, hydrogen-induced amorphization occurs. Mechanical tests conducted on the composite with varying hydrogen concentrations indicate that the Ti50Zr25Cu25 alloy is significantly resistant to hydrogen embrittlement when compared to conventional amorphous alloys. A possible mechanism that would contribute toward hydrogen-induced amorphization and hydrogen embrittlement is discussed.

scholarly journals Computational and experimental investigations of one-step conversion of poly(carbonate)s into value-added poly(aryl ether sulfone)s

2016 ◽  
Vol 113 (28) ◽  
pp. 7722-7726 ◽  
Author(s):  
Gavin O. Jones ◽  
Alexander Yuen ◽  
Rudy J. Wojtecki ◽  
James L. Hedrick ◽  
Jeannette M. García
Keyword(s):  
High Performance ◽  
Density Functional ◽  
Value Added ◽  
Single Step ◽  
Nucleophilic Attack ◽  
Experimental Investigations ◽  
Aryl Ether ◽  
One Step ◽  
Poly Carbonate

It is estimated that ∼2.7 million tons poly(carbonate)s (PCs) are produced annually worldwide. In 2008, retailers pulled products from store shelves after reports of bisphenol A (BPA) leaching from baby bottles, reusable drink bottles, and other retail products. Since PCs are not typically recycled, a need for the repurposing of the PC waste has arisen. We report the one-step synthesis of poly(aryl ether sulfone)s (PSUs) from the depolymerization of PCs and in situ polycondensation with bis(aryl fluorides) in the presence of carbonate salts. PSUs are high-performance engineering thermoplastics that are commonly used for reverse osmosis and water purification membranes, medical equipment, as well as high temperature applications. PSUs generated through this cascade approach were isolated in high purity and yield with the expected thermal properties and represent a procedure for direct conversion of one class of polymer to another in a single step. Computational investigations performed with density functional theory predict that the carbonate salt plays two important catalytic roles in this reaction: it decomposes the PCs by nucleophilic attack, and in the subsequent polyether formation process, it promotes the reaction of phenolate dimers formed in situ with the aryl fluorides present. We envision repurposing poly(BPA carbonate) for the production of value-added polymers.

Experimental Investigations on Aluminium Ultrasonic Welding Parameters

2014 ◽  
Vol 657 ◽  
pp. 306-310
Author(s):  
Lăcrămioara Apetrei ◽  
Vasile Rață ◽  
Ruxandra Rață ◽  
Elena Raluca Bulai
Keyword(s):  
Microstructural Analysis ◽  
Base Material ◽  
Welding Process ◽  
Ultrasonic Welding ◽  
Experimental Investigations ◽  
Welding Parameters ◽  
Material Structure ◽  
Welding Temperature ◽  
Wide Range ◽  
Made In

Research evolution timely tendencies, in the nonconventional technologies field, are: manufacture conditions optimization and complex equipments design. The increasing of ultrasonic machining use, in various technologies is due to the expanding need of a wide range materials and high quality manufacture standards in many activity fields. This paper present a experimental study made in order to analyze the welded zone material structure and welding quality. The effects of aluminium ultrasonic welding parameters such as relative energy, machining time, amplitude and working force were compared through traction tests values and microstructural analysis. Microhardness tests were, also, made in five different points, two in the base material and three in the welded zone, on each welded aluminium sample. The aluminum welding experiments were made at the National Research and Development Institute for Welding and Material Testing (ISIM) Timişoara. The ultrasonic welding temperature is lower than the aluminium melting temperature, that's so our experiments reveal that the aluminium ultrasonic welding process doesn't determine the appearance of moulding structure. In the joint we have only crystalline grains deformation, phase transformation and aluminium diffusion.

In Situ Produced MMC Layer by Laser Melt Injection

2010 ◽  
Vol 649 ◽  
pp. 61-66
Author(s):  
Zoltán Kálazi ◽  
Viktória Janó ◽  
Gábor Buza
Keyword(s):  
Carbon Content ◽  
Composite Layer ◽  
Pure Titanium ◽  
Base Material ◽  
Titanium Content ◽  
Steel Sample ◽  
Low Carbon ◽  
The Matrix ◽  
Ti Powder

Tungsten (W) based alloy composite layer reinforced with TiC particles has been successfully prepared on unalloyed steel sample by LMI technology. In order to obtain in situ produced TiC reinforcement, pure titanium has been introduced to the melt pool. WC powder was added for increasing the carbon content of the layer in order to avoid the softening of the matrix (with low carbon content) during TiC formation. The present study aims to investigate the optimum amount of injected WC and Ti powder to improve wear resistance and hardness of the layer. Samples were investigated using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The maximum hardness of the layer has been reached ~900HV in case of 2-4wt% of titanium content. Ti has been collected all of the carbon from the matrix when titanium content was 9,6wt%, which resulted that the austenite and (Fe,W)6C phases have been disappeared. Only α-Fe and TiC phases were presented in the layer. The hardness of the layer reduced to the hardness of the base material.

Sign in / Sign up

Export Citation Format

Share Document