Analysis of a Weld Overlay to Address Fatigue Cracking in a Stainless Steel Nozzle

2018 ◽  
Author(s):  
S. E. Marlette ◽  
A. Udyawar ◽  
J. Broussard
Keyword(s):  
Stainless Steel ◽  
Residual Stresses ◽  
Stress Corrosion ◽  
Crack Growth ◽  
Stress Corrosion Cracking ◽  
Fatigue Cracking ◽  
Corrosion Cracking ◽  
Nuclear Industry ◽  
Pressurized Water ◽  
Design Life

For several decades the nuclear industry has used structural weld overlays (SWOL) to repair and mitigate cracking within pressurized water reactor (PWR) components such as nozzles, pipes and elbows. There are two known primary mechanisms that have led to cracking within PWR components. One source of cracking has been primary water stress corrosion cracking (PWSCC). Numerous SWOL repairs and mitigations were installed in the early 2000s to address PWSCC in components such as pressurizer nozzles. However, nearly all of the likely candidate components for SWOL repairs have now been addressed in the industry. The other cause for cracking has been by fatigue, which usually results from thermal cycling events such as leakage caused by a faulty valve close to the component. The PWR components of most concern for fatigue cracking are mainly stainless steel. Thus, ASME Section XI Code Case N-504-4 would be a likely basis for SWOL repairs of these components, although this Code Case was originally drafted to address stress corrosion cracking (SCC) in boiling water reactors (BWR). N-504-4 includes the requirements for the SWOL design and subsequent analyses to establish the design life for the overlay based on predicted crack growth after the repair. This paper presents analysis work performed using Code Case N-504-4 to establish the design life of a SWOL repair applied to a boron injection tank (BIT) line nozzle attached to the cold leg of an operating PWR. The overlay was applied to the nozzle to address flaws found within the stainless steel base metal during inservice examination. Analyses were performed to calculate the residual stresses resulting from the original fabrication and the subsequent SWOL repair. In addition, post-SWOL operating stresses were calculated to demonstrate that the overlay does not invalidate the ASME Section III design basis for the nozzle and attached pipe. The operating and residual stresses were also used for input to a fatigue crack growth (FCG) analysis in order to establish the design life of the overlay. Lastly, the weld shrinkage from the application of overlay was evaluated for potential impact on the attached piping, restraints and valves within the BIT line. The combined analyses of the installed SWOL provide a basis for continued operation for the remaining life of the plant.

Stress Corrosion Cracking (SCC) of Nickel-Base Weld Metals in PWR Primary Water

2013 ◽  
Vol 747-748 ◽  
pp. 723-732 ◽  
Author(s):  
Ru Xiong ◽  
Ying Jie Qiao ◽  
Gui Liang Liu
Keyword(s):  
Residual Stresses ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Surface Condition ◽  
Cold Work ◽  
Corrosion Cracking ◽  
Pressurized Water ◽  
Weld Metals ◽  
Surface Residual Stresses ◽  
Primary Water

This discussion reviewed the occurrence of stress corrosion cracking (SCC) of alloys 182 and 82 weld metals in primary water (PWSCC) of pressurized water reactors (PWR) from both operating plants and laboratory experiments. Results from in-service experience showed that more than 340 Alloy 182/82 welds have sustained PWSCC. Most of these cases have been attributed to the presence of high residual stresses produced during the manufacture aside from the inherent tendency for Alloy 182/82 to sustain SCC. The affected welds were not subjected to a stress relief heat treatment with adjacent low alloy steel components. Results from laboratory studies indicated that time-to-cracking of Alloy 82 was a factor of 4 to 10 longer than that for Alloy 182. PWSCC depended strongly on the surface condition, surface residual stresses and surface cold work, which were consistent with the results of in-service failures. Improvements in the resistance of advanced weld metals, Alloys 152 and 52, to PWSCC were discussed.

Weld Residual Stresses and Primary Water Stress Corrosion Cracking in Bimetal Nuclear Pipe Welds

2007 ◽  
Author(s):  
Frederick W. Brust ◽  
Paul M. Scott
Keyword(s):  
Water Stress ◽  
Residual Stresses ◽  
Weld Metal ◽  
Stress Corrosion ◽  
Crack Growth ◽  
Stress Corrosion Cracking ◽  
Pressure Vessel ◽  
Large Diameter ◽  
Corrosion Cracking ◽  
Primary Water

There have been incidents recently where cracking has been observed in the bi-metallic welds that join the hot leg to the reactor pressure vessel nozzle. The hot leg pipes are typically large diameter, thick wall pipes. Typically, an inconel weld metal is used to join the ferritic pressure vessel steel to the stainless steel pipe. The cracking, mainly confined to the inconel weld metal, is caused by corrosion mechanisms. Tensile weld residual stresses, in addition to service loads, contribute to PWSCC (Primary Water Stress Corrosion Cracking) crack growth. In addition to the large diameter hot leg pipe, cracking in other piping components of different sizes has been observed. For instance, surge lines and spray line cracking has been observed that has been attributed to this degradation mechanism. Here we present some models which are used to predict the PWSCC behavior in nuclear piping. This includes weld model solutions of bimetal pipe welds along with an example calculation of PWSCC crack growth in a hot leg. Risk based considerations are also discussed.

NRC/EPRI Residual Stress Validation Program Phase I: Experimental Specimen Modeling and Measurement

2011 ◽  
Author(s):  
J. Broussard ◽  
P. Crooker
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Phase 1 ◽  
Measurement Techniques ◽  
Corrosion Cracking ◽  
Welding Residual Stress ◽  
Hole Drilling ◽  
Pressurized Water

The US Nuclear Regulatory Commission (NRC) and the Electric Power Research Institute (EPRI) are working cooperatively under a memorandum of understanding to validate welding residual stress predictions in pressurized water reactor primary cooling loop components containing dissimilar metal welds. These stresses are of interest as DM welds in pressurized water reactors are susceptible to primary water stress corrosion cracking (PWSCC) and tensile weld residual stresses are one of the primary drivers of this stress corrosion cracking mechanism. The NRC/EPRI weld residual stress (WRS) program currently consists of four phases, with each phase increasing in complexity from lab size specimens to component mock-ups and ex-plant material. This paper describes the Phase 1 program, which comprised an initial period of learning and research for both FEA methods and measurement techniques using simple welded specimens. The Phase 1 specimens include a number of plate and cylinder geometries, each designed to provide a controlled configuration for maximum repeatability of measurements and modeling. A spectrum of surface and through-wall residual stress measurement techniques have been explored using the Phase 1 specimens, including incremental hole drilling, ring-core, and x-ray diffraction for surface stresses and neutron diffraction, deep-hole drilling, and contour method for through-wall stresses. The measured residual stresses are compared to the predicted stress results from a number of researchers employing a variety of modeling techniques. Comparisons between the various measurement techniques and among the modeling results have allowed for greater insight into the impact of various parameters on predicted versus measured residual stress. This paper will also discuss the technical challenges and lessons learned as part of the DM weld materials residual stress measurements.

scholarly journals A Study on Microstructure, Residual Stresses and Stress Corrosion Cracking of Repair Welding on 304 Stainless Steel: Part I-Effects of Heat Input

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2416
Author(s):  
Yun Luo ◽  
Wenbin Gu ◽  
Wei Peng ◽  
Qiang Jin ◽  
Qingliang Qin ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Heat Input ◽  
Corrosion Cracking ◽  
304 Stainless Steel ◽  
Sensitivity Index ◽  
Repair Welding

In this paper, the effect of repair welding heat input on microstructure, residual stresses, and stress corrosion cracking (SCC) sensitivity were investigated by simulation and experiment. The results show that heat input influences the microstructure, residual stresses, and SCC behavior. With the increase of heat input, both the δ-ferrite in weld and the average grain width decrease slightly, while the austenite grain size in the heat affected zone (HAZ) is slightly increased. The predicted repair welding residual stresses by simulation have good agreement with that by X-ray diffraction (XRD). The transverse residual stresses in the weld and HAZ are gradually decreased as the increases of heat input. The higher heat input can enhance the tensile strength and elongation of repaired joint. When the heat input was increased by 33%, the SCC sensitivity index was decreased by more than 60%. The macroscopic cracks are easily generated in HAZ for the smaller heat input, leading to the smaller tensile strength and elongation. The larger heat input is recommended in the repair welding in 304 stainless steel.

An Analytical Evaluation of the Effect of Weld Material Thickness on Residual Stresses Produced by Structural Weld Overlays on Pressurized Water Reactor Primary Cooling Piping

2009 ◽  
Author(s):  
L. F. Fredette ◽  
Paul M. Scott ◽  
F. W. Brust ◽  
A. Csontos
Keyword(s):  
Residual Stresses ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Corrosion Cracking ◽  
Intergranular Stress Corrosion ◽  
Pressurized Water ◽  
Weld Overlay ◽  
Water Reactor ◽  
Dissimilar Metal ◽  
Structural Reinforcement

Full Structural Weld Overlay (FSWOL) has been used successfully to mitigate intergranular stress corrosion cracking in boiling water reactor (BWR) welded stainless steel piping for many years. The FSWOL technique adds structural reinforcement, can add crack resistant material, and can create compressive residual stresses at the inside surface of the welded joint which reduces the possibility of further stress corrosion cracking. Recently, the FSWOL has been applied as a preemptive measure to prevent primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR) on susceptible welded pipes with dissimilar metal welds common to PWR primary cooling piping. This study uses finite element models to evaluate the likely residual and operating stress profiles remaining after FSWOL and describes the results of sensitivity studies which were performed to examine the effect of weld overlay thickness on the residual stresses for typical dissimilar metal weld configurations.

Continuity of Environmentally Assisted Fatigue and Stress Corrosion Cracking Based on Short Crack Growth Behavior of 316 Stainless Steel in Simulated PWR Primary Water

2017 ◽  
Author(s):  
Choongmoo Shim ◽  
Yoichi Takeda ◽  
Tetsuo Shoji
Keyword(s):  
Stainless Steel ◽  
Stress Corrosion ◽  
Crack Growth ◽  
Stress Corrosion Cracking ◽  
Water Environment ◽  
Growth Behavior ◽  
Corrosion Cracking ◽  
Short Crack ◽  
Crack Growth Behavior ◽  
Primary Water

Environmental correction factor (Fen) is one of the parameters to evaluate the effect of a pressurized high temperature water environment. It has been reported that Fen for stainless steel saturates at a very low strain rate. However, the relationship between environmentally assisted fatigue (EAF) and stress corrosion cracking (SCC) is still unclear. The aim of this study is to investigate the short crack growth behavior and possible continuity of EAF and SCC at very low strain rates. Short crack initiation and propagation have similar behaviors, which retard the crack growth between 100–200 μm in depth. We find that the striation spacing correlates well with the maximum crack growth rate (CGR) data. Based on the correlation, it is clarified that the local CGR on an intergranular facet was faster than that on a transgranular facet. Furthermore, the overall maximum and average CGR from the EAF data is well interpreted and compared with the SCC data.

Failure Probability Analysis Based on FRI Model for Stress Corrosion Cracking Growth Introducing Residual Stress Distribution by Weld

2012 ◽  
Author(s):  
Noriyoshi Maeda ◽  
Tetsuo Shoji
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Stress Distribution ◽  
Stress Corrosion ◽  
Crack Growth ◽  
Stress Corrosion Cracking ◽  
Failure Probability ◽  
Corrosion Cracking ◽  
Protective Film

Failure probability of welds by stress corrosion cracking (SCC) in austenitic stainless steel piping is analyzed by a probabilistic fracture mechanics (PFM) approach based on an electro-chemical crack growth model (FRI model, where FRI stands for “Fracture and Reliability Research Institute” of Tohoku University in Japan). In this model, crack growth rate da/dt, where a is crack depth, is anticipated as the rate of chemical corrosion process defined by electro-chemical Coulomb’s law. The process is also related to the strain rate at the crack tip, taking the small scale yielding into consideration. Compared to the mechanical crack growth equation like the power law for SCC, FRI model can introduce many parameters affecting the generation and break of protective film on the crack surface such as electric current associated with corrosion, the frequency of protective film break and mechanical parameters such as the stress intensity factor K and its change with time dK/dt. Derived transcendental equation is transformed into non-dimensional form, and then solved numerically by iterative method. The extension of surface crack by SCC under residual stress field is simulated by developing the stress distribution in polynomial form following ASME section XI appendix A. This simulation scheme is introduced into PFM framework to derive the failure probability of austenitic stainless steel piping in nuclear power plants to be used in developing a risk-informed inservice inspection (RI-ISI) program.

An Analytical Evaluation of the Effect of Weld Sequencing on Residual Stresses Produced by Full Structural Weld Overlays on Pressurized Water Reactor Primary Cooling Piping

2009 ◽  
Author(s):  
L. F. Fredette ◽  
Paul M. Scott ◽  
F. W. Brust ◽  
A. Csontos
Keyword(s):  
Residual Stresses ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Cooling System ◽  
Corrosion Cracking ◽  
Intergranular Stress Corrosion ◽  
Pressurized Water ◽  
Water Reactor ◽  
Dissimilar Metal ◽  
Structural Reinforcement

Full Structural Weld Overlay (FSWOL) has been used successfully to mitigate intergranular stress corrosion cracking in boiling water reactor (BWR) welded stainless steel piping for many years. The FSWOL technique adds structural reinforcement, can add crack resistant material, and can create compressive residual stresses at the inside surface of the welded joint which reduces the possibility of further stress corrosion cracking. Recently, the FSWOL has been applied as a preemptive measure to prevent primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR) on susceptible welded pipes with dissimilar metal welds common to PWR primary cooling piping. This study uses finite element models to evaluate the likely residual and operating stress profiles remaining after FSWOL for typical dissimilar metal weld configurations and describes the results of sensitivity studies which were performed to examine the effect of weld sequencing on the residual stresses produced in common configurations of PWR primary cooling system piping.

Technical Basis for Code Case N-894 Alternative Rules for Repair of Classes 1, 2, and 3 Austenitic Stainless Steel Piping With Thermal Fatigue Cracking

2020 ◽  
Author(s):  
Stephen Marlette ◽  
Steven L. McCraken ◽  
Christopher Lohse
Keyword(s):  
Stainless Steel ◽  
Stress Corrosion ◽  
Thermal Fatigue ◽  
Stress Corrosion Cracking ◽  
Fatigue Cracking ◽  
Corrosion Cracking ◽  
Weld Overlay ◽  
Water Reactors ◽  
Technical Basis ◽  
Weld Overlays

Abstract Since 1982 the nuclear industry has employed weld overlay repairs to address intergranular stress corrosion cracking (IGSCC) in boiling water reactors (BWR) and primary water stress corrosion cracking (PWSCC) in pressurized water reactors (PWR). The American Society of Mechanical Engineers (ASME) has created several documents to provide rules and guidelines for weld overlay repair of nuclear components that have experienced stress corrosion cracking (SCC). These documents include ASME Code Case N-504-4 and ASME Section XI, Nonmandatory Appendix Q which specifically address weld overlay repair of stainless steel components. Recently, stainless steel components that have experienced thermal fatigue cracking at the inner diameter surfaces have been repaired with structural weld overlays (SWOL) using the methodology of Code Cases N-504-4 and N-740-2. The SWOL is a good choice for repair of thermal fatigue cracks in piping because it provides structural reinforcement to the affected location and places the inside diameter (ID) surface into compression preventing, or significantly reducing, further flaw growth. However, the rules of Case N-504-4 and N-740 were not specifically written to address thermal fatigue cracking as the primary cause and may not adequately address design, analysis and examination requirements when thermal fatigue is the active mechanism because it is very different in nature than SCC. For example, SCC is driven by a combination of environment, steady state operating stresses, residual stresses from welding and fabrication processes, and operating temperature, whereas thermal fatigue is driven by thermal stress cycles resulting from fluid thermal cycling or stratification. The source of the thermal events that result in cracking may not be as well understood or predictable as SCC degradation. In addition, weld overlays applied to address SCC are constructed of SCC resistant material but are not resistant to thermal fatigue. Therefore, ASME Section XI recognized that alternative rules were needed for repair of piping damaged by thermal fatigue. This paper provides a technical basis for weld overlay repair of components that have experienced thermal fatigue cracking. It addresses design, analysis and examination requirements considering the nature of thermal fatigue in nuclear piping systems. The Code Case was originally drafted based on the industry accepted rules of Case N-504-4 and Appendix Q but includes appropriate modifications needed to address thermal fatigue cracking. These modifications include removing restrictions such as the delta ferrite limit for PWRs that is only applicable to address SCC in BWR environments, and enhancements to the examination requirements to ensure that the repaired location is adequately monitored throughout the remaining service life of the plant. The purpose of this paper is to document the technical basis for Code Case N-894, which is currently still under development by ASME Section XI.

Crack Growth Rate Testing and Large Plate Demonstration Under Chloride-Induced Stress Corrosion Cracking Conditions in Stainless Steel Canisters for Storage of Spent Nuclear Fuel

2019 ◽  
Author(s):  
Poh-Sang Lam ◽  
Andrew J. Duncan ◽  
Lisa N. Ward ◽  
Robert L. Sindelar ◽  
Yun-Jae Kim ◽  
...  
Keyword(s):  
Growth Rate ◽  
Stainless Steel ◽  
Crack Growth Rate ◽  
Stress Corrosion ◽  
Crack Growth ◽  
Nuclear Fuel ◽  
Stress Corrosion Cracking ◽  
Spent Nuclear Fuel ◽  
Compact Tension ◽  
Corrosion Cracking

Abstract Stress corrosion cracking may occur when chloride-bearing salts deposit and deliquesce on the external surface of stainless steel spent nuclear fuel storage canisters at weld regions with high residual stresses. Although it has not yet been observed, this phenomenon leads to a confinement concern for these canisters due to its potential for radioactive materials breaching through the containment system boundary provided by the canister wall during extended storage. The tests for crack growth rate have been conducted on bolt-load compact tension specimens in a setup designed to allow initially dried salt deposits to deliquesce and infuse to the crack front under conditions relevant to the canister storage environments (e.g., temperature and humidity). The test and characterization protocols are performed to provide bounding conditions in which cracking will occur. The results after 2- and 6-month exposure are examined in relation to previous studies in condensed brine and compared with other experimental data in the open literature. The knowledge gained from bolt-load compact tension testing is being applied to a large plate cut from a mockup commercial spent nuclear fuel canister to demonstrate the crack growth behavior induced from starter cracks machined in regions where the welding residual stress is expected. All these tests are conducted to support the technical basis for ASME Boiler and Pressure Vessel Section XI Code Case N-860.

Sign in / Sign up

Export Citation Format

Share Document