A Parametric Study of Variable Crack Initiation Criterion in XFEM on Pipeline Steel

2020 ◽  
Author(s):  
Meng Lin ◽  
Yong Li ◽  
Mohammad Salem ◽  
J. J. Roger Cheng ◽  
Samer Adeeb ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Crack Initiation ◽  
Parametric Study ◽  
Pipeline Steel ◽  
Stress Triaxiality ◽  
Element Analysis ◽  
Physical Test ◽  
Crack Initiation Criterion ◽  
Element Method

Abstract The integrity decisions for cracked pipelines can be made based on the conventional Finite Element Method (FEM). However, it is extremely time-consuming due to the requirement of remeshing to continuously conform to the geometric discontinuities as the crack propagates. The more recently developed Extended Finite Element Method (XFEM) provides a more robust approach in which a crack can propagate through the finite element analysis mesh and thus alleviates the requirement for remeshing. However, the current criteria for crack initiation and propagation in XFEM framework have not been calibrated to pipeline steels. The current built-in criterion in Abaqus assumes a fixed value as the damage strain. Crack initiation occurs after this strain is exceeded. However, the accuracy of numerical crack propagating path is questionable, especially in a side-grooved single edge notched tension (SENT) model. Faster crack initiation at specimen side over the center conflicts with the actual crack propagating path obtained from a physical test. This paper develops a new crack initiation criterion which defines a variable damage strain as a function of the stress configuration at the crack tip. The criterion is modified from the Mohr-Coulomb fracture criterion as a function of stress triaxiality and Lode angle parameters. The damage strain exponentially decreases as the stress triaxiality increases. This paper presents a parametric study on the effects of material parameters considered in the criterion on the development of damage strain locus. The new crack initiation criterion is applied to a side-grooved SENT model, in which the corresponding failure mechanism is defined by the user’s subroutine UDMGINI in Abaqus.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Tire Cornering Simulation Using an Explicit Finite Element Analysis Code

1998 ◽  
Vol 26 (2) ◽  
pp. 109-119 ◽  
Author(s):  
M. Koishi ◽  
K. Kabe ◽  
M. Shiratori
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Test System ◽  
Experimental Results ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Explicit Finite Element ◽  
Explicit Finite Element Analysis ◽  
Element Method

Abstract The finite element method has been used widely in tire engineering. Most tire simulations using the finite element method are static analyses, because tires are very complex nonlinear structures. Recently, transient phenomena have been studied with explicit finite element analysis codes. In this paper, the authors demonstrate the feasibility of tire cornering simulation using an explicit finite element code, PAM-SHOCK. First, we propose the cornering simulation using the explicit finite element analysis code. To demonstrate the efficiency of the proposed simulation, computed cornering forces for a 175SR14 tire are compared with experimental results from an MTS Flat-Trac Tire Test System. The computed cornering forces agree well with experimental results. After that, parametric studies are conducted by using the proposed simulation.

Parametric Study of a Simply Supported Composite Plate Using Finite Element Method

2014 ◽  
Vol 4 (4) ◽  
pp. 26-33
Author(s):  
P.Deepak Kumar ◽  
◽  
Ishan Sharma ◽  
P.R. Maiti ◽  
◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Parametric Study ◽  
Composite Plate ◽  
Simply Supported ◽  
Element Method

A Fracture Mechanics Based Parametric Study of the Copper-to-Copper Direct Thermo-Compression Bonded Interface Using Finite Element Method

2013 ◽  
Author(s):  
Ah-Young Park ◽  
Satish Chaparala ◽  
Seungbae Park
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Parametric Study ◽  
Initial Crack ◽  
Bonding Interface ◽  
Interface Condition ◽  
Large Temperature ◽  
Bonded Interface ◽  
The Impact ◽  
Element Method

Through-silicon via (TSV) technology is expected to overcome the limitations of I/O density and helps in enhancing system performance of conventional flip chip packages. One of the challenges for producing reliable TSV packages is the stacking and joining of thin wafers or dies. In the case of the conventional solder interconnections, many reliability issues arise at the interface between solder and copper bump. As an alternative solution, Cu-Cu direct thermo-compression bonding (CuDB) is a possible option to enable three-dimension (3D) package integration. CuDB has several advantages over the solder based micro bump joining, such as reduction in soldering process steps, enabling higher interconnect density, enhanced thermal conductivity and decreased concerns about intermetallic compounds (IMC) formation. Critical issue of CuDB is bonding interface condition. After the bonding process, Cu-Cu direct bonding interface is obtained. However, several researchers have reported small voids at the bonded interface. These defects can act as an initial crack which may lead to eventual fracture of the interface. The fracture could happen due to the thermal expansion coefficient (CTE) mismatch between the substrate and the chip during the postbonding process, board level reflow or thermal cycling with large temperature changes. In this study, a quantitative assessment of the energy release rate has been made at the CuDB interface during temperature change finite element method (FEM). A parametric study is conducted to analyze the impact of the initial crack location and the material properties of surrounding materials. Finally, design recommendations are provided to minimize the probability of interfacial delamination in CuDB.

scholarly journals Shape Sensing of a Complex Aeronautical Structure with Inverse Finite Element Method

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1388
Author(s):  
Daniele Oboe ◽  
Luca Colombo ◽  
Claudio Sbarufatti ◽  
Marco Giglio
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Boundary Conditions ◽  
Strain Field ◽  
Element Analysis ◽  
Inverse Finite Element Method ◽  
Shape Sensing ◽  
Definition Of ◽  
High Level ◽  
Element Method

The inverse Finite Element Method (iFEM) is receiving more attention for shape sensing due to its independence from the material properties and the external load. However, a proper definition of the model geometry with its boundary conditions is required, together with the acquisition of the structure’s strain field with optimized sensor networks. The iFEM model definition is not trivial in the case of complex structures, in particular, if sensors are not applied on the whole structure allowing just a partial definition of the input strain field. To overcome this issue, this research proposes a simplified iFEM model in which the geometrical complexity is reduced and boundary conditions are tuned with the superimposition of the effects to behave as the real structure. The procedure is assessed for a complex aeronautical structure, where the reference displacement field is first computed in a numerical framework with input strains coming from a direct finite element analysis, confirming the effectiveness of the iFEM based on a simplified geometry. Finally, the model is fed with experimentally acquired strain measurements and the performance of the method is assessed in presence of a high level of uncertainty.

scholarly journals COMPARISON OF SAW BLADE NATURAL FREQUENCIES AND CRITICAL SPEEDS USING CSAW AND FINITE ELEMENT ANALYSIS

2011 ◽  
Author(s):  
J. Poirier ◽  
P. Radziszewski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Saw Blade ◽  
Circular Saws ◽  
The Finite Element Model ◽  
Element Method

The natural frequencies of circular saws limit the operating speeds of the saws. Current industry methods of increasing natural frequency include pretensioning, where plastic deformation is induced into the saw. To better model the saw, the finite element model is compared to current software for steel saws; C-SAW, a software program that calculates frequencies for stiffened circular saws. Using C-SAW and the finite element method the results are compared and the finite element method is validated for steel saws.

scholarly journals Experimental Results of SiC reinforced Al2O3 Matrix Ceramic Matrix Composites Validated with Finite Element Method

2019 ◽  
Vol 8 (12) ◽  
pp. 307-310
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Ceramic Matrix Composites ◽  
Experimental Results ◽  
Matrix Composites ◽  
Metal Oxidation ◽  
Element Analysis ◽  
Advanced Analysis ◽  
Al2o3 Matrix ◽  
Element Method

In this paper, SiCp /Al2O3 composites were fabricated through directed metal oxidation process. Experimental results of these composites validated or compared with Finite Element Method (FEM). Finite Element has become one in all the foremost necessary tools offered to an engineer. The finite part methodology is employed to resolve advanced analysis issues. In this paper, Finite Element Method based ANSYS software is used to FEM model to determine mechanical properties of SiC reinforced Al2O3 matrix composite by changing volume fractions of SiC. The comparison of experimental results with Finite element analysis provides detailed information about the results of these comparisons. The FA was competent of predict the information for several scenario quite fine

Probabilistic Finite-Element Analysis of Airfield Pavements

1996 ◽  
Vol 1540 (1) ◽  
pp. 29-38 ◽  
Author(s):  
Yuan Jie Lua ◽  
Robert H. Sues
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Spatial Variability ◽  
Life Prediction ◽  
Homogeneous Layer ◽  
Response Analysis ◽  
Element Analysis ◽  
Analysis And Design ◽  
Pavement Structures ◽  
Element Method

Mechanistic pavement analysis and design based on either layered elastic analysis (LEA) or the finite element method (FEM) is increasingly being used to replace the empirical design process. The simplifying assumptions of a uniform, homogeneous layer of linear material used in LEA can render its analysis inaccurate for real pavement structures. The FEM is more attractive for structural analysis of pavements; the generality of the FEM also allows both the use of comprehensive material models and modeling of the spatial variability that exists in pavement systems. To date, spatial variability and uncertainty are ignored in pavement system finite element analyses. Ignoring spatial variability and uncertainty implies a false sense of accuracy in the results and can lead to inaccurate assessment of the pavement. The first application of the probabilistic finite element method to pavement response analysis and life prediction and the first investigation of the effects of spatial variability on pavement life prediction are presented. It is concluded that the probabilistic FEA, with spatial variability, is a more accurate representation of the true physical condition and leads to results that are less conservative than those obtained with probabilistic LEA.

Sign in / Sign up

Export Citation Format

Share Document