An Experimental and Numerical Investigation Into the Effects of Squealer Blade Tip Modifications on Aerodynamic Performance

2013 ◽  
Author(s):  
G. A. Ledezma ◽  
J. Allen ◽  
R. S. Bunker
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Turbine Blades ◽  
Suction Side ◽  
Aerodynamic Performance ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Numerical Predictions ◽  
Blade Tip

Gas turbine blades using the so-called squealer tip configuration represent a majority of the high-pressure first stage blades in service. The squealer tip in its most basic format is simply a two-tooth labyrinth seal projecting from the blade tip towards the stationary shroud or casing. As with all blade tip configurations, the geometry is a compromise between aerodynamics, cooling, mechanical stress, durability, and repair. While many proposed blade tip innovations involve more complex geometries, this study seeks to determine if a simpler geometry, other than a flat tip, can provide equivalent aerodynamic performance with a reasonable chance of satisfying all other design factors. Using an annular sector blade cascade, total pressure loss surveys are measured with three blade tip geometries, the standard squealer tip, a single-sided suction side seal strip, and the single-sided strip with a pressure side winglet added. The same cascade is modeled numerically as a periodic passage for each of the geometries tested. Experiment and simulation both utilize all blade tip cooling flow injection locations and nominal magnitudes, as well as a constant tip clearance above the suction side seal strip. Experimental data show that the removal of the pressure side seal strip reduces the area-averaged total pressure loss slightly, while the addition of a winglet returns the performance to the baseline result. Numerical predictions indicate essentially equal performance for all geometries. The numerical results provide insight into the loss mechanisms of both the tip leakage flows and the coolant injection flows. This study, when combined with literature data on heat transfer and cooling, concludes that the simpler single-sided suction seal strip is better overall than the commonly employed squealer tip.

Aerodynamic optimisation of a winglet-cavity tip in a high-pressure axial turbine cascade

2016 ◽  
Vol 232 (4) ◽  
pp. 649-663 ◽  
Author(s):  
Zhihua Zhou ◽  
Shaowen Chen ◽  
Songtao Wang
Keyword(s):  
High Pressure ◽  
Mass Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Suction Side ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Tip Clearance Flow ◽  
Clearance Flow

Tip clearance flow between rotating blades and the stationary casing in high-pressure turbines is very complex and is one of the most important factors influencing turbine performance. The rotor with a winglet-cavity tip is often used as an effective method to improve the loss resulting from the tip clearance flow. In this study, an aerodynamic geometric optimisation of a winglet-cavity tip was carried out in a linear unshrouded high-pressure axial turbine cascade. For the purpose of shaping the efficient winglet geometry of the rotor tip, a novel parameterisation method has been introduced in the optimisation procedure based on the computational fluid dynamics simulation and analysis. The reliability of a commercial computational fluid dynamics code with different turbulence models was first validated by contrasting with the experimental results, and the numerical total pressure loss and flow angle using the Baseline k-omega Model (BSL κ-ω model) shows a better agreement with the test data. Geometric parameterisation of blade tips along the pressure side and suction side was adopted to optimise the tip clearance flow, and an optimal winglet-cavity tip was proven to achieve lower tip leakage mass flow rate and total pressure loss than the flat tip and cavity tip. Compared to the numerical results of flat tip and cavity tip, the optimised winglet-cavity design, with the winglet along the pressure side and suction side, had lower tip leakage mass flow rate and total pressure loss. It offered a 35.7% reduction in the change ratio [Formula: see text]. In addition, the optimised winglet along pressure side and suction side, respectively, by using the parameterisation method was studied for investigating the individual effect of the pressure-side winglet and suction-side winglet on the tip clearance flow. It was found that the suction-side extension of the optimal winglet resulted in a greater reduction of aerodynamic loss and leakage mass flow than the pressure-side extension of the optimal winglet. Moreover, with the analysis based on the tip flow pattern, the numerical results show that the pressure-side winglet reduced the contraction coefficient, and the suction-side winglet reduced the aerodynamic loss effectively by decreasing the driving pressure difference near the blade tips, the leakage flow velocity, and the interaction between the leakage flow and the main flow. Overall, a better aerodynamic performance can be obtained by adopting the pressure-side and suction-side winglet-cavity simultaneously.

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

2021 ◽  
Author(s):  
Feng Li ◽  
Zhao Liu ◽  
Zhenping Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Cooling Performance ◽  
Pressure Loss Coefficient ◽  
Blade Tip ◽  
Total Pressure Loss Coefficient

Abstract The blade tip region of the shroud-less high-pressure gas turbine is exposed to an extremely operating condition with combined high temperature and high heat transfer coefficient. It is critical to design new tip structures and apply effective cooling method to protect the blade tip. Multi-cavity squealer tip has the potential to reduce the huge thermal loads and improve the aerodynamic performance of the blade tip region. In this paper, numerical simulations were performed to predict the aerothermal performance of the multi-cavity squealer tip in a heavy-duty gas turbine cascade. Different turbulence models were validated by comparing to the experimental data. It was found that results predicted by the shear-stress transport with the γ-Reθ transition model have the best precision. Then, the film cooling performance, the flow field in the tip gap and the leakage losses were presented with several different multi-cavity squealer tip structures, under various coolant to mainstream mass flow ratios (MFR) from 0.05% to 0.15%. The results show that the ribs in the multi-cavity squealer tip could change the flow structure in the tip gap for that they would block the coolant and the leakage flow. In this study, the case with one-cavity (1C) achieves the best film cooling performance under a lower MFR. However, the cases with multi-cavity (2C, 3C, 4C) show higher film cooling effectiveness under a higher MFR of 0.15%, which are 32.6%%, 34.2%% and 41.0% higher than that of the 1C case. For the aerodynamic performance, the case with single-cavity has the largest total pressure loss coefficient in all MFR studied, whereas the case with two-cavity obtains the smallest total pressure loss coefficient, which is 7.6% lower than that of the 1C case.

Effect of Rotor Tip Winglet on the Performance and Stability of a Transonic Axial Compressor

2017 ◽  
Author(s):  
Subbaramu Shivaramaiah ◽  
Quamber H. Nagpurwala ◽  
Mahesh K. Varpe ◽  
H. K. Narahari
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Axial Compressor ◽  
Suction Side ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Compressor Stage ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Overall Performance

Winglets are plane surfaces with certain thickness and different shapes. Winglets are used in aircraft to reduce wing tip vortex which is created due to differential pressure in between pressure surface and suction surface. In transonic axial compressor, rotor tip leakage vortex interaction with shock layer and shroud boundary layer leads to total pressure loss and initiation of stall phenomenon. Effect of tip winglets are investigated in compressor rotor cascade. Cascade investigation shows that rotor tip winglet are able to reduce total pressure loss due to tip leakage flow and blade passage secondary flow. Cascade studies are performed with winglet on blade suction side, pressure side and combination of both. From cascade studies it is revealed that suction side winglet are aerodynamically better than pressure side and combined winglets. Owing to favorable results of tip winglet on compressor cascade performance, it was assumed that tip winglets would enhance overall performance of transonic compressor stage with rotating rotor. Results of present CFD simulations have predicted both positive and negative effects of winglets. Effect of different winglet configurations on pressure side and suction side of rotor blade tip are investigated to analyze the compressor stage overall performance. Rotor tip winglets are able to increase stage total pressure ratio compare to the baseline stage without winglet. Stage with winglets have shown better performance in choke region. Winglets are able to vary rotor blade loading from hub to tip region. Presence of winglet has shown ability to reduce to total pressure loss in trailing edge wake region. Stall margin is decreased in compressor stage with winglets due to more blockage towards trailing edge in tip region.

Conjugate Heat Transfer Characteristics of Double Wall Cooling With Gradient Diameter of Film and Impingement Holes

2021 ◽  
Author(s):  
Juan He ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Flow Direction ◽  
Turbine Blades ◽  
Total Pressure Loss ◽  
Advanced Technique ◽  
Cooling Effectiveness ◽  
Uniform Pattern ◽  
Double Wall

Abstract Double wall cooling, consisting of internal impingement cooling and external film cooling, is believed to be the most advanced technique in modern turbine blades cooling. In this paper, to improve the uniformity of temperature distribution, a flat plate double wall cooling model with gradient diameter of film and impingement holes was proposed, and the heat transfer and flow characteristics were investigated by solving steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equations with SST k-ω turbulence model. The influence of gradient diameter on overall cooling effectiveness and total pressure loss was studied by comparing with the uniform pattern at the blowing ratios ranging from 0.5 to 2. For gradient diameter of film hole patterns, results show that −10% film pattern always has the lowest film flow non-uniformity coefficient. The laterally averaged overall cooling effectiveness of uniform pattern lies between that of +10% and −10% film patterns, but the intersection of three patterns moves upstream from the middle of flow direction with the increase of blowing ratio. Therefore, the −10% film pattern exerts the highest area averaged cooling effectiveness, which is improved by up to 1.6% and 1% at BR = 0.5 and 1 respectively compared with a uniform pattern. However, at higher blowing ratios, the +10% film pattern maintains higher cooling effectiveness and lower total pressure loss. For gradient diameter of impingement hole patterns, the intersection of laterally averaged overall cooling effectiveness in three patterns is located near the middle of flow direction under all blowing ratios. The uniform pattern has the highest area averaged cooling effectiveness and the smallest non-uniform coefficient, but the −10% jet pattern has advantages of reducing pressure loss, especially in the laminated loss.

scholarly journals Effects of Tip Clearance Gap and Exit Mach Number on Turbine Blade Tip and Near-Tip Heat Transfer

2013 ◽  
Author(s):  
K. Anto ◽  
S. Xue ◽  
W. F. Ng ◽  
L. J. Zhang ◽  
H. K. Moon
Keyword(s):  
Heat Transfer ◽  
Mach Number ◽  
Turbine Blade ◽  
Leading Edge ◽  
Suction Side ◽  
Tip Clearance ◽  
Pressure Side ◽  
Engine Blade ◽  
Blade Tip ◽  
Exit Mach Number

This study focuses on local heat transfer characteristics on the tip and near-tip regions of a turbine blade with a flat tip, tested under transonic conditions in a stationary, 2-D linear cascade with high freestream turbulence. The experiments were conducted at the Virginia Tech transonic blow-down wind tunnel facility. The effects of tip clearance and exit Mach number on heat transfer distribution were investigated on the tip surface using a transient infrared thermography technique. In addition, thin film gages were used to study similar effects in heat transfer on the near-tip regions at 94% height based on engine blade span of the pressure and suction sides. Surface oil flow visualizations on the blade tip region were carried-out to shed some light on the leakage flow structure. Experiments were performed at three exit Mach numbers of 0.7, 0.85, and 1.05 for two different tip clearances of 0.9% and 1.8% based on turbine blade span. The exit Mach numbers tested correspond to exit Reynolds numbers of 7.6 × 105, 9.0 × 105, and 1.1 × 106 based on blade true chord. The tests were performed with a high freestream turbulence intensity of 12% at the cascade inlet. Results at 0.85 exit Mach showed that an increase in the tip gap clearance from 0.9% to 1.8% translates into a 3% increase in the average heat transfer coefficients on the blade tip surface. At 0.9% tip clearance, an increase in exit Mach number from 0.85 to 1.05 led to a 39% increase in average heat transfer on the tip. High heat transfer was observed on the blade tip surface near the leading edge, and an increase in the tip clearance gap and exit Mach number augmented this near-leading edge tip heat transfer. At 94% of engine blade height on the suction side near the tip, a peak in heat transfer was observed in all test cases at s/C = 0.66, due to the onset of a downstream leakage vortex, originating from the pressure side. An increase in both the tip gap and exit Mach number resulted in an increase, followed by a decrease in the near-tip suction side heat transfer. On the near-tip pressure side, a slight increase in heat transfer was observed with increased tip gap and exit Mach number. In general, the suction side heat transfer is greater than the pressure side heat transfer, as a result of the suction side leakage vortices.

Influence of a Novel 3D Leading Edge Geometry on the Aerodynamic Performance of Low Pressure Turbine Blade Cascade Vanes

2014 ◽  
Author(s):  
A. Asghar ◽  
W. D. E. Allan ◽  
M. LaViolette ◽  
R. Woodason
Keyword(s):  
Turbine Blade ◽  
Pressure Loss ◽  
Total Pressure ◽  
Separated Flow ◽  
Leading Edge ◽  
Low Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Low Pressure Turbine ◽  
Edge Geometry

This paper addresses the issue of aerodynamic performance of a novel 3D leading edge modification to a reference low pressure turbine blade. An analysis of tubercles found in nature and used in some engineering applications was employed to synthesize new leading edge geometry. A sinusoidal wave-like geometry characterized by wavelength and amplitude was used to modify the leading edge along the span of a 2D profile, rendering a 3D blade shape. The rationale behind using the sinusoidal leading edge was that they induce streamwise vortices at the leading edge which influence the separation behaviour downstream. Surface pressure and total pressure measurements were made in experiments on a cascade rig. These were complemented with computational fluid dynamics studies where flow visualization was also made from numerical results. The tests were carried out at low Reynolds number of 5.5 × 104 on a well-researched profile representative of conventional low pressure turbine profiles. The performance of the new 3D leading edge geometries was compared against the reference blade revealing a downstream shift in separated flow for the LE tubercle blades; however, total pressure loss reduction was not conclusively substantiated for the blade with leading edge tubercles when compared with the performance of the baseline blade. Factors contributing to the total pressure loss are discussed.

Aerodynamic Performance of Suction-Side Gill Region Film Cooling

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Justin Chappell ◽  
Phil Ligrani ◽  
Sri Sreekanth ◽  
Terry Lucas ◽  
Edward Vlasic
Keyword(s):  
Mach Number ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Suction Side ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Blowing Ratio ◽  
Exit Mach Number ◽  
Total Pressure Loss Coefficient

The performance of suction-side gill region film cooling is investigated using the University of Utah transonic wind tunnel and a simulated turbine vane in a two-dimensional cascade. The effects of film cooling hole orientation, shape, and number of rows, and their resulting effects on the aerodynamic losses, are considered for four different hole configurations: round axial (RA), shaped axial (SA), round radial (RR), and round compound (RC). The mainstream Reynolds number based on axial chord is 500,000, exit Mach number is 0.35, and the tests are conducted using the first row of holes, or both rows of holes at blowing ratios of 0.6 and 1.2. Carbon dioxide is used as the injectant to achieve density ratios of 1.77–1.99 similar to values present in operating gas turbine engines. Presented are the local distributions of total pressure loss coefficient, local normalized exit Mach number, and local normalized exit kinetic energy. Integrated aerodynamic losses (IAL) increase anywhere from 4% to 45% compared with a smooth blade with no film injection. The performance of each hole type depends on the airfoil configuration, film cooling configuration, mainstream flow Mach number, number of rows of holes, density ratio, and blowing ratio, but the general trend is an increase in IAL as either the blowing ratio or the number of rows of holes increase. In general, the largest total pressure loss coefficient Cp magnitudes and the largest IAL are generally present at any particular wake location for the RR or SA configurations, regardless of the film cooling blowing ratio and number of holes. The SA holes also generally produce the highest local peak Cp magnitudes. IAL magnitudes are generally lowest with the RA hole configuration. A one-dimensional mixing loss correlation for normalized IAL values is also presented, which matches most of the both rows data for RA, SA, RR, and RC hole configurations. The equation also provides good representation of the RA, RC, and RR first row data sets.

Effect of Turbine Blade tip shape on the Total Pressure Loss of a Turbine Cascade

2009 ◽  
Vol 12 (2) ◽  
pp. 39-45 ◽  
Author(s):  
Ki-Seon Lee ◽  
Seoung-Duck Park ◽  
Young-Chul Noh ◽  
Hak-Bong Kim ◽  
Jae-Su Kwak ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Turbine Cascade ◽  
Blade Tip

Impact of a Combination of Micro-Vortex Generator and Boundary Layer Suction on Performance in a High-Load Compressor Cascade

2018 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Chuanle Liu
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Control Methods ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Micro Vortex Generator

The performance of a compressor cascade is considerably influenced by flow control methods. In this paper, the synergistic effects of combination between micro-vortex generators (MVG) and boundary layer suction (BLS) are discussed in a high-load compressor cascade. Seven cases, which are grouped by a kind of micro-vortex generator and boundary layer suction with three locations, are investigated to control secondary flow effects and enhance the aerodynamic performance of the compressor cascade. The MVG is mounted on the end-wall in front of the passage. The rectangle suction slot with three radial positions is installed on the blade suction surface near the trailing edge. The numerical results show that: at the design condition, the total pressure loss is effectively decreased as well as the static pressure coefficient increase when the combined MVG and SBL method (COM) is used, which is superior to MVG in an aerodynamic performance. At the stall condition, the induced vortex coming from MVG could mix the low-energy fluid and mainstream, which result in the reduced separation, and the total pressure loss decreased by 11.54% when the suction flow ratio is 1.5%. The total pressure loss decreases by 14.59% when the COM control methods are applied.

Investigation on Performance of Compressor Cascade with Tubercle Leading Edge Blade

2020 ◽  
Vol 37 (3) ◽  
pp. 295-303 ◽  
Author(s):  
Tu Baofeng ◽  
Zhang Kai ◽  
Hu Jun
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Large Scale ◽  
Design Method ◽  
Leading Edge ◽  
Experimental Tests ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Linear Compressor Cascade

AbstractIn order to improve compressor performance using a new design method, which originates from the fins on a humpback whale, experimental tests and numerical simulations were undertaken to investigate the influence of the tubercle leading edge on the aerodynamic performance of a linear compressor cascade with a NACA 65–010 airfoil. The results demonstrate that the tubercle leading edge can improve the aerodynamic performance of the cascade in the post-stall region by reducing total pressure loss, with a slight increase in total pressure loss in the pre-stall region. The tubercles on the leading edge of the blades cause the flow to migrate from the peak to the valley on the blade surface around the tubercle leading edge by the butterfly flow. The tubercle leading edge generates the vortices similar to those created by vortex generators, splitting the large-scale separation region into multiple smaller regions.

Sign in / Sign up

Export Citation Format

Share Document