Aerodynamic optimisation of a winglet-cavity tip in a high-pressure axial turbine cascade

2016 ◽  
Vol 232 (4) ◽  
pp. 649-663 ◽  
Author(s):  
Zhihua Zhou ◽  
Shaowen Chen ◽  
Songtao Wang
Keyword(s):  
High Pressure ◽  
Mass Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Suction Side ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Tip Clearance Flow ◽  
Clearance Flow

Tip clearance flow between rotating blades and the stationary casing in high-pressure turbines is very complex and is one of the most important factors influencing turbine performance. The rotor with a winglet-cavity tip is often used as an effective method to improve the loss resulting from the tip clearance flow. In this study, an aerodynamic geometric optimisation of a winglet-cavity tip was carried out in a linear unshrouded high-pressure axial turbine cascade. For the purpose of shaping the efficient winglet geometry of the rotor tip, a novel parameterisation method has been introduced in the optimisation procedure based on the computational fluid dynamics simulation and analysis. The reliability of a commercial computational fluid dynamics code with different turbulence models was first validated by contrasting with the experimental results, and the numerical total pressure loss and flow angle using the Baseline k-omega Model (BSL κ-ω model) shows a better agreement with the test data. Geometric parameterisation of blade tips along the pressure side and suction side was adopted to optimise the tip clearance flow, and an optimal winglet-cavity tip was proven to achieve lower tip leakage mass flow rate and total pressure loss than the flat tip and cavity tip. Compared to the numerical results of flat tip and cavity tip, the optimised winglet-cavity design, with the winglet along the pressure side and suction side, had lower tip leakage mass flow rate and total pressure loss. It offered a 35.7% reduction in the change ratio [Formula: see text]. In addition, the optimised winglet along pressure side and suction side, respectively, by using the parameterisation method was studied for investigating the individual effect of the pressure-side winglet and suction-side winglet on the tip clearance flow. It was found that the suction-side extension of the optimal winglet resulted in a greater reduction of aerodynamic loss and leakage mass flow than the pressure-side extension of the optimal winglet. Moreover, with the analysis based on the tip flow pattern, the numerical results show that the pressure-side winglet reduced the contraction coefficient, and the suction-side winglet reduced the aerodynamic loss effectively by decreasing the driving pressure difference near the blade tips, the leakage flow velocity, and the interaction between the leakage flow and the main flow. Overall, a better aerodynamic performance can be obtained by adopting the pressure-side and suction-side winglet-cavity simultaneously.

An Experimental and Numerical Investigation Into the Effects of Squealer Blade Tip Modifications on Aerodynamic Performance

2013 ◽  
Author(s):  
G. A. Ledezma ◽  
J. Allen ◽  
R. S. Bunker
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Turbine Blades ◽  
Suction Side ◽  
Aerodynamic Performance ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Numerical Predictions ◽  
Blade Tip

Gas turbine blades using the so-called squealer tip configuration represent a majority of the high-pressure first stage blades in service. The squealer tip in its most basic format is simply a two-tooth labyrinth seal projecting from the blade tip towards the stationary shroud or casing. As with all blade tip configurations, the geometry is a compromise between aerodynamics, cooling, mechanical stress, durability, and repair. While many proposed blade tip innovations involve more complex geometries, this study seeks to determine if a simpler geometry, other than a flat tip, can provide equivalent aerodynamic performance with a reasonable chance of satisfying all other design factors. Using an annular sector blade cascade, total pressure loss surveys are measured with three blade tip geometries, the standard squealer tip, a single-sided suction side seal strip, and the single-sided strip with a pressure side winglet added. The same cascade is modeled numerically as a periodic passage for each of the geometries tested. Experiment and simulation both utilize all blade tip cooling flow injection locations and nominal magnitudes, as well as a constant tip clearance above the suction side seal strip. Experimental data show that the removal of the pressure side seal strip reduces the area-averaged total pressure loss slightly, while the addition of a winglet returns the performance to the baseline result. Numerical predictions indicate essentially equal performance for all geometries. The numerical results provide insight into the loss mechanisms of both the tip leakage flows and the coolant injection flows. This study, when combined with literature data on heat transfer and cooling, concludes that the simpler single-sided suction seal strip is better overall than the commonly employed squealer tip.

Effect of Rotor Tip Winglet on the Performance and Stability of a Transonic Axial Compressor

2017 ◽  
Author(s):  
Subbaramu Shivaramaiah ◽  
Quamber H. Nagpurwala ◽  
Mahesh K. Varpe ◽  
H. K. Narahari
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Axial Compressor ◽  
Suction Side ◽  
Total Pressure Loss ◽  
Pressure Side ◽  
Compressor Stage ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Overall Performance

Winglets are plane surfaces with certain thickness and different shapes. Winglets are used in aircraft to reduce wing tip vortex which is created due to differential pressure in between pressure surface and suction surface. In transonic axial compressor, rotor tip leakage vortex interaction with shock layer and shroud boundary layer leads to total pressure loss and initiation of stall phenomenon. Effect of tip winglets are investigated in compressor rotor cascade. Cascade investigation shows that rotor tip winglet are able to reduce total pressure loss due to tip leakage flow and blade passage secondary flow. Cascade studies are performed with winglet on blade suction side, pressure side and combination of both. From cascade studies it is revealed that suction side winglet are aerodynamically better than pressure side and combined winglets. Owing to favorable results of tip winglet on compressor cascade performance, it was assumed that tip winglets would enhance overall performance of transonic compressor stage with rotating rotor. Results of present CFD simulations have predicted both positive and negative effects of winglets. Effect of different winglet configurations on pressure side and suction side of rotor blade tip are investigated to analyze the compressor stage overall performance. Rotor tip winglets are able to increase stage total pressure ratio compare to the baseline stage without winglet. Stage with winglets have shown better performance in choke region. Winglets are able to vary rotor blade loading from hub to tip region. Presence of winglet has shown ability to reduce to total pressure loss in trailing edge wake region. Stall margin is decreased in compressor stage with winglets due to more blockage towards trailing edge in tip region.

Numerical Simulation of Tip Clearance Control in Axial Turbine Rotor: Part 2—Passive Control of Five Different Tip Platforms

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Passive Control ◽  
Suction Side ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

The tip leakage flow has significant effects on turbine in loss production, aerodynamic efficiency, etc. Then it’s important to minimize these effects for a better performance by adopting corresponding flow control. The active turbine tip clearance flow control with injection from the tip platform is given in Part-1 of this paper. This paper is Part-2 of the two-part papers focusing on the effect of five different passive turbine tip clearance flow control methods on the tip clearance flow physics, which consists of a partial suction side squealer tip (Partial SS Squealer), a double squealer tip (Double Side Squealer), a pressure side tip shelf with inclined squealer tip on a double squealer tip (Improved PS Squealer), a tip platform extension edge in pressure side (PS Extension) and in suction side (SS Extension) respectively. Combined with the turbine rotor and the numerical method mentioned in Part 1, the effects of passive turbine tip clearance flow controls on the tip clearance flow were sequentially simulated. The detailed tip clearance flow fields with different squealer rims were described with the streamline and the velocity vector in various planes parallel to the tip platform or normal to the tip leakage vortex core. Accordingly, the mechanisms of five passive controls were put in evidence; the effects of the passive controls on the turbine efficiency and the tip clearance flow field were highlighted. The results show that the secondary flow loss near the outer casing including the tip leakage flow and the casing boundary layer can be reduced in all the five passive control methods. Comparing the active control with the passive control, the effect brought by the active injection control on the tip leakage flow is evident. The turbine rotor efficiency could be increased via the rational passive turbine tip clearance flow control. The Improved PS Squealer had the best effect on turbine rotor efficiency, and it increased by 0.215%.

Method for Non-Dimensional Tip Leakage Flow Characterization in Radial Turbines

2018 ◽  
Author(s):  
José Ramón Serrano ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Lukas Benjamin Inhestern
Keyword(s):  
Suction Side ◽  
Tip Clearance ◽  
Navier Stokes ◽  
The Novel ◽  
Tip Leakage Flow ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Wide Range ◽  
Clearance Flow

Tip leakage loss characterization and modeling plays an important role in small size radial turbine research. The momentum of the flow passing through the tip gap is highly related with the tip leakage losses. The ratio of fluid momentum driven by the pressure gradient between suction side and pressure side and the fluid momentum caused by the shroud friction has been widely used to analyze and to compare different sized tip clearances. However, the commonly used number for building this momentum ratio lacks some variables, as the blade tip geometry data and the viscosity of the used fluid. To allow the comparison between different sized turbocharger turbine tip gaps, work has been put into finding a consistent characterization of radial tip clearance flow. Therefore, a non-dimensional number has been derived from the Navier Stokes Equation. This number can be calculated like the original ratio over the chord length. Using the results of wide range CFD data, the novel tip leakage number has been compared with the traditional and widely used ratio. Furthermore, the novel tip leakage number can be separated into three different non-dimensional factors. First, a factor dependent on the radial dimensions of the tip gap has been found. Second, a factor defined by the viscosity, the blade loading, and the tip width has been identified. Finally, a factor that defines the coupling between both flow phenomena. These factors can further be used to filter the tip gap flow, obtained by CFD, with the influence of friction driven and pressure driven momentum flow.

Numerical Simulation of Deposition Phenomena on High-Pressure Turbine Vane Using UPACS

2019 ◽  
Author(s):  
Kenta Mizutori ◽  
Koji Fukudome ◽  
Makoto Yamamoto ◽  
Masaya Suzuki
Keyword(s):  
Numerical Simulation ◽  
High Pressure ◽  
Flow Field ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
High Pressure Turbine ◽  
Pressure Loss Coefficient ◽  
Turbine Vane ◽  
Total Pressure Loss Coefficient

Abstract We performed numerical simulation to understand deposition phenomena on high-pressure turbine vane. Several deposition models were compared and the OSU model showed good adaptation to any flow field and material, so it was implemented on UPACS. After the implementation, the simulations of deposition phenomenon in several cases of the flow field were conducted. From the results, particles adhere on the leading edge and the trailing edge side of the pressure surface. Also, the calculation of the total pressure loss coefficient was conducted after computing the flow field after deposition. The total pressure loss coefficient increased after deposition and it was revealed that the deposition deteriorates aerodynamic performance.

scholarly journals Preliminary Experimental Study on Pressure Loss Coefficients of Exhaust Manifold Junction

2014 ◽  
Vol 2014 ◽  
pp. 1-10
Author(s):  
Xiao-lu Lu ◽  
Kun Zhang ◽  
Wen-hui Wang ◽  
Shao-ming Wang ◽  
Kang-yao Deng
Keyword(s):  
Mass Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Flow Ratio ◽  
Pressure Loss Coefficient ◽  
Loss Coefficients ◽  
Total Pressure Loss Coefficient ◽  
Mass Flow Ratio

The flow characteristic of exhaust system has an important impact on inlet boundary of the turbine. In this paper, high speed flow in a diesel exhaust manifold junction was tested and simulated. The pressure loss coefficient of the junction flow was analyzed. The steady experimental results indicated that both of static pressure loss coefficientsL13andL23first increased and then decreased with the increase of mass flow ratio of lateral branch and public manifold. The total pressure loss coefficientK13always increased with the increase of mass flow ratio of junctions 1 and 3. The total pressure loss coefficientK23first increased and then decreased with the increase of mass flow ratio of junctions 2 and 3. These pressure loss coefficients of the exhaust pipe junctions can be used in exhaust flow and turbine inlet boundary conditions analysis. In addition, simulating calculation was conducted to analyze the effect of branch angle on total pressure loss coefficient. According to the calculation results, total pressure loss coefficient was almost the same at low mass flow rate of branch manifold 1 but increased with lateral branch angle at high mass flow rate of branch manifold 1.

scholarly journals Investigation of Unsteady Tip Clearance Flow in a Low-Speed One and Half Stage Axial Compressor With LES and PIV

2015 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz ◽  
David Tan
Keyword(s):  
Axial Compressor ◽  
Suction Side ◽  
Flow Fields ◽  
Tip Clearance ◽  
Gap Size ◽  
Tip Clearance Flow ◽  
Gap Flow ◽  
Clearance Flow ◽  
Single Structure ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate how a rotor’s unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor when the rotor tip gap size is increased from 0.5 mm (0.49% of rotor tip blade chord, 2% of blade span) to 2.4 mm (2.34% chord, 4% span) at the design condition are investigated. The changes in unsteady tip clearance flow with the 0.62 % tip gap as the flow rate is reduced to near stall condition are also investigated. A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at these three flow conditions. Detailed Stereoscopic PIV (SPIV) measurements of the current flow fields were also performed at the Johns Hopkins University in a refractive index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. Unsteady tip clearance flow fields from LES are compared with the PIV measurements and both LES and PIV results are used to study changes in tip clearance flow structures. The current study shows that the tip clearance vortex is not a single structure as traditionally perceived. The tip clearance vortex is formed by multiple interlaced vorticities. Therefore, the tip clearance vortex is inherently unsteady. The multiple interlaced vortices never roll up to form a single structure. When phased-averaged, the tip clearance vortex appears as a single structure. When flow rate is reduced with the same tip gap, the tip clearance vortex rolls further upstream and the tip clearance vortex moves further radially inward and away from the suction side of the blade. When the tip gap size is increased at the design flow condition, the overall tip clearance vortex becomes stronger and it stays closer to the blade suction side and the vortex core extends all the way to the exit of the blade passage. Measured and calculated unsteady flow fields inside the tip gap agree fairly well. Instantaneous velocity vectors inside the tip gap from both the PIV and LES do show flow separation and reattachment at the entrance of tip gap as some earlier studies suggested. This area at the entrance of tip gap flow (the pressure side of the blade) is confined very close to the rotor tip section. With a small tip gap (0.5mm), the gap flow looks like a simple two-dimensional channel flow with larger velocity near the casing for both flow rates. A small area with a sharp velocity gradient is observed just above the rotor tip. This strong shear layer is turned radially inward when it collides with the incoming flow and forms the core structure of the tip clearance vortex. When tip gap size is increased to 2.4 mm at the design operation, the radial profile of the tip gap flow changes drastically. With the large tip gap, the gap flow looks like a two-dimensional channel flow only near the casing. Near the rotor top section, a bigger region with very large shear and reversed flow is observed.

Aerodynamic Performance of Suction-Side Gill Region Film Cooling

2010 ◽  
Vol 132 (3) ◽  
Author(s):  
Justin Chappell ◽  
Phil Ligrani ◽  
Sri Sreekanth ◽  
Terry Lucas ◽  
Edward Vlasic
Keyword(s):  
Mach Number ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Suction Side ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Blowing Ratio ◽  
Exit Mach Number ◽  
Total Pressure Loss Coefficient

The performance of suction-side gill region film cooling is investigated using the University of Utah transonic wind tunnel and a simulated turbine vane in a two-dimensional cascade. The effects of film cooling hole orientation, shape, and number of rows, and their resulting effects on the aerodynamic losses, are considered for four different hole configurations: round axial (RA), shaped axial (SA), round radial (RR), and round compound (RC). The mainstream Reynolds number based on axial chord is 500,000, exit Mach number is 0.35, and the tests are conducted using the first row of holes, or both rows of holes at blowing ratios of 0.6 and 1.2. Carbon dioxide is used as the injectant to achieve density ratios of 1.77–1.99 similar to values present in operating gas turbine engines. Presented are the local distributions of total pressure loss coefficient, local normalized exit Mach number, and local normalized exit kinetic energy. Integrated aerodynamic losses (IAL) increase anywhere from 4% to 45% compared with a smooth blade with no film injection. The performance of each hole type depends on the airfoil configuration, film cooling configuration, mainstream flow Mach number, number of rows of holes, density ratio, and blowing ratio, but the general trend is an increase in IAL as either the blowing ratio or the number of rows of holes increase. In general, the largest total pressure loss coefficient Cp magnitudes and the largest IAL are generally present at any particular wake location for the RR or SA configurations, regardless of the film cooling blowing ratio and number of holes. The SA holes also generally produce the highest local peak Cp magnitudes. IAL magnitudes are generally lowest with the RA hole configuration. A one-dimensional mixing loss correlation for normalized IAL values is also presented, which matches most of the both rows data for RA, SA, RR, and RC hole configurations. The equation also provides good representation of the RA, RC, and RR first row data sets.

Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade

2014 ◽  
Vol 599-601 ◽  
pp. 368-371
Author(s):  
Zhi Hui Xu ◽  
He Bin Lv ◽  
Ru Bin Zhao
Keyword(s):  
Computational Simulation ◽  
Suction Side ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow ◽  
Blade Tip

Using blade tip winglet to control the tip leakage flow has been concerned in the field of turbomachinery. Computational simulation was conducted to investigate the phenomenological features of tip clearance flow. The simulation results show that suction-side winglet can reduce leakage flow intensity. The tip winglet can also decrease tip leakage mass flow and weaken tip leakage flow mixing with the mainstream and therefore reduce the total pressure loss at the blade tip.

The Effects of Water Ingestion on the Tip Clearance Flow in Compressor Rotors

2018 ◽  
Author(s):  
Lu Yang ◽  
Xiaocui Wu ◽  
Desheng Qin ◽  
Qun Zheng ◽  
Hai Zhang
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
External Disturbance ◽  
Rotating Stall ◽  
Droplet Breakup ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Water Ingestion ◽  
Clearance Flow ◽  
Wet Compression

As the first core component of commercial aviation engines, compressor is likely to ingest a serious amount of liquid water into its path flow during the situation of heavy rain. Under the influence of centrifugal force, the tip region of compressor rotors may be filled with water. Unfortunately, the instability of tip clearance flow is a major reason for rotating stall. In order to explore the effects of water ingestion on the steady operating boundary of compressor, the change characteristics of tip clearance flow have been investigated in this research by using numerical simulation method. In reality, the compression process after water ingestion can be regarded as a special wet compression. Therefore, on the basis of existing wet compression study, the ingested mass flow and the mean droplet diameters were set as 1% of inlet air flow as well as 100 μm respectively to investigate how does water ingestion affects the flow field at the tip clearance of rotors. The typical trajectory of water droplet in compressor has been researched firstly to simply understand the situation of water ingestion and to verify the reliability of some special droplet breakup models. Then, the compressor performance in two states of dry and wet have been compared to indicate that the pressure ratio and adiabatic efficiency of compressor will decrease after water ingestion. Among them, the compression efficiency drops by 1∼2% as a whole compared with the dry condition, the operating point moves forward and the surge margin reduces slightly. The simulation results show that the presence of water droplets will change the distribution of airflow parameters along span direction, which leads to the decreases of mass flow rate and flow capacity of blade row, the increase of attack angel at tip region, and the separation of boundary layer in suction surface. Furthermore, the momentum losses caused by droplet impingement and breakup cause a sharp increase in the static entropy at the blade tip region as well. On the other hand, the ingestion of droplet brings an external disturbance to the flow, although it has some dissipated effects on the turbulence kinetic energy, it aggravates the unsteady characteristic of turbulent flow seriously at the tip region of blade.

Sign in / Sign up

Export Citation Format

Share Document