Applied research on real-time film and television animation virtual shooting for multiplayer action capture technology based on optical positioning and inertial attitude sensing technology

2021 ◽  
Vol 30 (03) ◽  
Author(s):  
Yongsheng Wang ◽  
Yifei Wang ◽  
Xu Lang
Author(s):  
Vincent Berardi ◽  
John Bellettiere ◽  
Benjamin Nguyen ◽  
Neil E Klepeis ◽  
Suzanne C Hughes ◽  
...  

Abstract Few studies have examined the relative effectiveness of reinforcing versus aversive consequences at changing behavior in real-world environments. Real-time sensing devices makes it easier to investigate such questions, offering the potential to improve both intervention outcomes and theory. This research aims to describe the development of a real-time, operant theory-based secondhand smoke (SHS) intervention and compare the efficacy of aversive versus aversive plus reinforcement contingency systems. Indoor air particle monitors were placed in the households of 253 smokers for approximately three months. Participants were assigned to a measurement-only control group (N = 129) or one of the following groups: 1.) aversive only (AO, N = 71), with aversive audio/visual consequences triggered by the detection of elevated air particle measurements, or 2.) aversive plus reinforcement (AP, N = 53), with reinforcing consequences contingent on the absence of SHS added to the AO intervention. Residualized change ANCOVA analysis compared particle concentrations over time and across groups. Post-hoc pairwise comparisons were also performed. After controlling for Baseline, Post-Baseline daily particle counts (F = 6.42, p = 0.002), % of time >15,000 counts (F = 7.72, p < 0.001), and daily particle events (F = 4.04, p = 0.02) significantly differed by study group. Nearly all control versus AO/AP pair-wise comparisons were statistically significant. No significant differences were found for AO versus AP groups. The aversive feedback system reduced SHS, but adding reinforcing consequences did not further improve outcomes. The complexity of real-world environments requires the nuances of these two contingency systems continue to be explored, with this study demonstrating that real-time sensing technology can serve as a platform for such research.


2010 ◽  
Vol 34-35 ◽  
pp. 1314-1318
Author(s):  
Xin Hua Wang ◽  
Shou Qiang Hu ◽  
Qian Yi Ya ◽  
Shu Wen Sun ◽  
Xiu Xia Cao

Structure and principle of a new kind of diphase opposition giant magnetostrictive self-sensing actuator (SSA for short) is introduced, for which a kind of double outputs high-precision NC stable voltage power is designed. With the method of combining with the hardware design and the software setting, the controllability and reliability of the actuator are greatly improved. And the whole design becomes more reasonable, which saves the cost and improves the practicability. In addition, based on the micro controller unit (MCU) with high-speed control, the scheme design of the real-time separation circuit for dynamic balance signal can effectively identify out and pick up the self-sensing signal which changes from foreign pressure feed back. Then the SSA real-time, dynamic and accurately control is realized. The experiment results show that the voltage power can high-speed and accurately output both output voltages with high current, and that the self-sensing signal decoupling circuit can isolate the self-sensing signals without distortion


2017 ◽  
Author(s):  
Runqi Han ◽  
Pradeepkumar Ashok ◽  
Mitchell Pryor ◽  
Eric van Oort ◽  
Paul Scott ◽  
...  

2019 ◽  
Vol 129 (5) ◽  
pp. 1319-1327 ◽  
Author(s):  
Ralf E. Gebhard ◽  
Tobias Moeller-Bertram ◽  
Douglas Dobecki ◽  
Feyce Peralta ◽  
Evan G. Pivalizza ◽  
...  

2013 ◽  
Vol 330 ◽  
pp. 561-564 ◽  
Author(s):  
Ming Li ◽  
Chun Ping Wang ◽  
Zhi Qiang Wang

In order to meet the real-time demands of some equipment networked test, the time synchronization techniques of ATS based traditional instrument buses are compared with the techniques of LXI ATS. Accordingly,the necessity of LXI ATS time synchronization technique study is put forward. The sorts of time synchronization techniques based on Local Area Network are analyzed. In addition, some methods which could improve the level of LXI data real-time communications are presented. Afterwards, technique realizations of PTP are studied in detail. Local Area Network techniques and IEEE 1588 Precise Time Protocol are adopted in the LXI Automatic Test System which designed in the paper, and the level of time synchronization precision in the system is improved.


Author(s):  
E. Tapanes

A proprietary fibre optic sensing technology has been developed and is capable of simultaneously utilising an existing fibre optic communication cable as an integrity-testing sensing cable, thus providing continuous, real-time monitoring of the fibre cable and any structure near the cable (ie., ground, tunnels, ducts, pipes, buildings, equipment, vessels, etc.). With this system, simultaneous fibre optic communications and real-time vibration monitoring was demonstrated using a wavelength multiplexed fibre system for a channel bandwidth of 500 MHz over 18 km of standard singlemode fibre. Real-time vibration monitoring was also demonstrated using standard singlemode and multimode fibre over lengths of 28 km and 53 km, respectively. Trials of the system are currently underway in Australia and the first commercial field installation with this capability is to be completed in mid-1998 in Indonesia. This paper highlights the benefits and potential of this dual-capacity system and details results obtained to-date.


Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 3123 ◽  
Author(s):  
Jonghyuk Kim ◽  
Hyunwoo Hwangbo

Recent paradigm shifts in manufacturing have resulted from the need for a smart manufacturing environment. In this study, we developed a model to detect anomalous signs in advance and embedded it in an existing programmable logic controller system. For this, we investigated the innovation process for smart manufacturing in the domain of synthetic rubber and its vulcanization process, as well as a real-time sensing technology. The results indicate that only analysis of the pattern of input variables can lead to significant results without the generation of target variables through manual testing of chemical properties. We have also made a practical contribution to the realization of a smart manufacturing environment by building cloud-based infrastructure and models for the pre-detection of defects.


2010 ◽  
Vol 143-144 ◽  
pp. 837-840
Author(s):  
Ying Li Liu ◽  
Te Liang Yan ◽  
Zhen Jiang

In the vibration isolating foundation buildings, build strong earthquake observation system, at the same time, join the seismic observation to this system, underground observation is carrying along with the observation of the seismic response on the ground and the buildings. The dynamic accelerator-type apparatus applied in the system, comes into being an accelerator-characteristics from 0.05HZ to 50HZ by electronics feeding back, enormously decrease affects of super low frequency interference and the linear and dynamic ranges can suffice the actual functions, avoids obviously errors of displacement-type apparatus in low frequencies, acquires satisfied effects.


Sign in / Sign up

Export Citation Format

Share Document