Magnetic properties, thermal stability, and structure of the nanocrystalline soft magnetic (Fe0.7Co0.3)88Hf2W2Mo2Zr1B4Cu1 alloy with induced magnetic anisotropy

2014 ◽  
Vol 115 (4) ◽  
pp. 326-334 ◽  
Author(s):  
N. V. Dmitrieva ◽  
V. A. Lukshina ◽  
E. G. Volkova ◽  
A. P. Potapov ◽  
B. N. Fillipov ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Magnetic Properties ◽  
Magnetic Anisotropy ◽  
Soft Magnetic ◽  
Induced Magnetic Anisotropy

Nanocrystalline Soft Magnetic Fe-, Co-Based Alloys Doped by Hf, Mo and Zr with Enhanced Thermal Stability of Magnetic Properties

2014 ◽  
Vol 215 ◽  
pp. 196-199
Author(s):  
Anatolii P. Potapov ◽  
Natalia V. Dmitrieva ◽  
Vera A. Lukshina ◽  
Elena G. Volkova ◽  
Boris N. Filippov
Keyword(s):  
Thermal Stability ◽  
Magnetic Properties ◽  
Magnetic Anisotropy ◽  
Easy Axis ◽  
Subsequent Annealing ◽  
Soft Magnetic ◽  
Different Temperatures ◽  
Thermal Stability Of

Magnetic properties, thermal stability and structure of the alloys - (Fe0.6Co0.4)86Hf7B6Cu1 (1), (Fe0.7Co0.3)88Hf7B4Cu1 (2) and (Fe0.7Co0.3)88Hf4Mo2Zr1B4Cu1 (3) obtained in the form of ribbons quenched from the melt were investigated after their nanocrystallization in the course of the thermal (TA) and stress (SA) annealings in the air at different temperatures. In all three alloys SA resulted in the induction of magnetic anisotropy with an easy axis along the direction of the ribbon. It is established that the alloy 3 after SA at 620°C for 20 min has the best thermal stability of magnetic properties, which remained practically unchanged after the subsequent annealing at 550°C for 26 hours. Magnetic properties of the alloys 1 and 2 subjected to SA under the same conditions did not change after annealing at 500°C.

Atomic structure of soft magnetic Fe-Si alloys with induced magnetic anisotropy

2006 ◽  
Vol 101 (S1) ◽  
pp. S59-S62 ◽  
Author(s):  
N. V. Ershov ◽  
Yu. P. Chernenkov ◽  
V. A. Lukshina ◽  
V. I. Fedorov ◽  
B. K. Sokolov
Keyword(s):  
Magnetic Anisotropy ◽  
Atomic Structure ◽  
Soft Magnetic ◽  
Induced Magnetic Anisotropy

Magnetic Properties and Structure of the Alloy Fe63.5Ni10Cu1Nb3Si13.5B9 with Induced Magnetic Anisotropy

2021 ◽  
Vol 122 (6) ◽  
pp. 533-539
Author(s):  
V. A. Lukshina ◽  
N. V. Dmitrieva ◽  
E. G. Volkova ◽  
D. A. Shishkin
Keyword(s):  
Magnetic Properties ◽  
Magnetic Anisotropy ◽  
Induced Magnetic Anisotropy

scholarly journals Optimization of Magnetic Properties of Magnetic Microwires by Post-Processing

Processes ◽  
2020 ◽  
Vol 8 (8) ◽  
pp. 1006
Author(s):  
Valentina Zhukova ◽  
Paula Corte-Leon ◽  
Lorena González-Legarreta ◽  
Ahmed Talaat ◽  
Juan Maria Blanco ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Chemical Composition ◽  
Hysteresis Loops ◽  
Structural Features ◽  
Post Processing ◽  
Soft Magnetic ◽  
Magnetic Microwires ◽  
Prepared State ◽  
Induced Magnetic Anisotropy ◽  
Selection Of

The influence of post-processing conditions on the magnetic properties of amorphous and nanocrystalline microwires has been thoroughly analyzed, paying attention to the influence of magnetoelastic, induced and magnetocrystalline anisotropies on the hysteresis loops of Fe-, Ni-, and Co-rich microwires. We showed that magnetic properties of glass-coated microwires can be tuned by the selection of appropriate chemical composition and geometry in as-prepared state or further considerably modified by appropriate post-processing, which consists of either annealing or glass-coated removal. Furthermore, stress-annealing or Joule heating can further effectively modify the magnetic properties of amorphous magnetic microwires owing to induced magnetic anisotropy. Devitrification of microwires can be useful for either magnetic softening or magnetic hardening of the microwires. Depending on the chemical composition of the metallic nucleus and on structural features (grain size, precipitating phases), nanocrystalline microwires can exhibit either soft magnetic properties or semi-hard magnetic properties. We demonstrated that the microwires with coercivities from 1 A/m to 40 kA/m can be prepared.

scholarly journals Field- and Stress-Induced Magnetic Anisotropy in Nanocrystalline Fe-Based and Amorphous Co-Based Alloys

1999 ◽  
Vol 32 (1-4) ◽  
pp. 289-294
Author(s):  
V. A. Lukshina ◽  
N. V. Dmitrieva ◽  
A. P. Potapov
Keyword(s):  
Magnetic Field ◽  
Magnetic Properties ◽  
Amorphous Alloy ◽  
Magnetic Anisotropy ◽  
Thermomechanical Treatment ◽  
Nanocrystalline Alloy ◽  
Complex Effect ◽  
Induced Magnetic Anisotropy ◽  
The Magnetic Field

For nanocrystalline alloy Fe73.5Cu1Nb3Si13.5B9 thermomechanical treatment was carried out simultaneously with nanocrystallizing annealing (1) or after it (2). It was shown that a change in magnetic properties for the case 1 is essentially greater than for the case 2. Complex effect of thermomagnetic and thermomechanical treatments on magnetic properties was studied in the above-mentioned nanocrystalline alloy as well as in the amorphous alloy Fe5Co70.6Si15B9.4., During the annealings both field and stress were aligned with the long side of the specimens. It was shown that the magnetic field, AC or DC, decreases an effect of loading. Moreover, the magnetic field, AC or DC, applied after stress-annealing can destroy the magnetic anisotropy already induced under load.

scholarly journals Effects of La on Thermal Stability, Phase Formation and Magnetic Properties of Fe–Co–Ni–Si–B–La High Entropy Alloys

Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1907
Author(s):  
Jiaming Li ◽  
Jianliang Zuo ◽  
Hongya Yu
Keyword(s):  
Thermal Stability ◽  
Magnetic Properties ◽  
Saturation Magnetization ◽  
Phase Formation ◽  
Crystallization Temperature ◽  
High Entropy Alloys ◽  
Soft Magnetic Properties ◽  
Soft Magnetic ◽  
High Entropy ◽  
Bcc Phase

The microstructure, phase formation, thermal stability and soft magnetic properties of melt-spun high entropy alloys (HEAs) Fe27Co27Ni27Si10−xB9Lax with various La substitutions for Si (x = 0, 0.2, 0.4, 0.6, 0.8, and 1) were investigated in this work. The Fe27Co27Ni27Si10−xB9La0.6 alloy shows superior soft magnetic properties with low coercivity Hc of ~7.1 A/m and high saturation magnetization Bs of 1.07 T. The content of La has an important effect on the primary crystallization temperature (Tx1) and the secondary crystallization temperature (Tx2) of the alloys. After annealing at relatively low temperature, the saturation magnetization of the alloy increases and the microstructure with a small amount of body-centered cubic (BCC) phase embedded in amorphous matrix is observed. Increasing the annealing temperature reduces the magnetization due to the transformation of BCC phase into face-centered cubic (FCC) phase.

scholarly journals Thermal Stability of Field- and Stress-Induced Anisotropy in Nanocrystalline Fe-Based and Amorphous Co-Based Alloys

1999 ◽  
Vol 32 (1-4) ◽  
pp. 281-287 ◽  
Author(s):  
N. V. Dmitrieva ◽  
V. A. Lukshina ◽  
G. V. Kurlyandskaya ◽  
A. P. Potapov
Keyword(s):  
Thermal Stability ◽  
Magnetic Anisotropy ◽  
Amorphous Alloys ◽  
Nanocrystalline Alloy ◽  
Induced Anisotropy ◽  
External Effects ◽  
Nanocrystalline And Amorphous ◽  
Induced Magnetic Anisotropy ◽  
Stress Induced Anisotropy ◽  
Thermal Stability Of

Thermal stability of induced magnetic anisotropy (IMA) was studied in a course of subsequent annealings without any external effects for already field- or stress-annealed specimens of the nanocrystalline Fe73.5Cu1Nb3Si13.5B9 and amorphous Fe3Co67Cr3Si15B12 alloys. For these alloys the dependence of IMA thermal stability on the magnitude of the IMA constant (Ku) and temperature of stress-annealing was investigated. For the nanocrystalline alloy thermal stability of field- and stress-induced anisotropy with identical Ku was compared. It was shown that nanocrystalline specimens with identical Ku values after field- or stress-annealing have identical thermal stability of IMA. This can point to a similarity of the mechanisms of IMA formation after field- or stress-annealings. Thermal stability of stress-induced anisotropy in the nanocrystalline alloy with Ku value less than 1000 J/m3 and the amorphous alloy with Ku less than 100 J/m3 depends on the value of Ku. For both stress-annealed nanocrystalline and amorphous alloys magnetic anisotropy induced at higher temperatures is more stable because more long-range and energy-taking processes take place at these temperatures.

Sign in / Sign up

Export Citation Format

Share Document