scholarly journals On the use of Fredlund gas–fluid compressibility relationship to model medium-dense gassy sand behavior

2019 ◽  
Vol 56 (8) ◽  
pp. 1070-1079 ◽  
Author(s):  
David G. Zapata-Medina ◽  
Carellys Y. Vergara ◽  
Carlos A. Vega-Posada ◽  
Luis G. Arboleda-Monsalve
Keyword(s):  
Pore Fluid ◽  
Experimental Program ◽  
Soil Parameters ◽  
Slight Reduction ◽  
Soil Behavior ◽  
Stress Strain ◽  
Soil Response ◽  
Wide Range ◽  
Constitutive Parameters ◽  
Fluid Compressibility

This paper presents the influence of gas bubbles trapped in a soil mass on the stress–strain–strength response of medium-dense sands. A hypoplastic constitutive sand model enhanced with the intergranular strain concept was coupled with the Fredlund gas–fluid compressibility relationship to capture gassy soil behavior. Boundary value element representations in a finite element platform of oedometer and saturated drained and undrained triaxial compression tests are performed for the calibration of soil parameters. For the numerical simulation of gassy soil behavior, pore fluid compressibility is modified to account for the presence of free gas in the pore fluid. The gassy soil mechanical response is studied by using only one set of parameters determined from the saturated soil response. The testing bed for this evaluation is a laboratory experimental program conducted on sands retrieved from the Oakridge Landfill, a sanitary landfill located in South Carolina, USA. The hypoplasticity sand model specialized with the Fredlund relationship reproduces reasonably well the stress–strain–strength response of these sands for a wide range of loading conditions and at a reasonable level of testing for the calibration of constitutive parameters. It is found that a slight reduction in the degree of saturation significantly decreases the undrained shear strength of the soil and causes changes in volume (i.e., drained-like behavior).

Determination and prediction of the stress-strain state of pipeline, taking into account soil changes during operation

2020 ◽  
Vol 10 (4) ◽  
pp. 372-378
Author(s):  
Aydar К. Gumerov ◽  
◽  
Rinat M. Karimov ◽  
Robert М. Askarov ◽  
Khiramagomed Sh. Shamilov ◽  
...  
Keyword(s):  
Strain State ◽  
Mathematical Framework ◽  
Equilibrium Equations ◽  
Stress Strain ◽  
Optimal Method ◽  
Initial Stress State ◽  
Soil Response ◽  
Stress Strain State ◽  
Support Reaction ◽  
Key Factor

The key factor determining the strength, reliability, service life and fail-safe operation of the main pipeline is its stress-strain state. The purpose of this article is to develop a mathematical framework and methodology for calculating the stress-strain state of a pipeline section laid in complex geotechnical conditions, taking into account all planned and altitude changes and impacts at various points of operation, as well as during repair and after its completion. The mathematical framework is based on differential equations reflecting the equilibrium state of the pipeline, taking into account the features of the sections (configuration, size, initial stress state, acting forces, temperature conditions, interaction with soil, supports, and pipe layers). The equilibrium equations are drawn up in a curvilinear coordinate system – the same one that is used for in-pipe diagnostics. According to the results of the solution, all stress components are determined at each point both along the length of the pipeline and along the circumference of any section. At the same time, transverse and longitudinal forces, bending moments, shearing forces, pipeline displacements relative to the ground and soil response to displacements are determined. As an example, a solution is given using the developed mathematical framework. During the course of calculation, the places where the lower form of the pipe does not touch the ground and the places where the support reaction becomes higher than a predetermined limit are determined. A comparative analysis was accomplished, and the optimal method for section repair has been selected.

Qualitative Analysis of Underlying Factors Affecting Vaccine Hesitancy in Iran- A Study Protocol (Preprint)

2020 ◽  
Author(s):  
Salime Goharinezhad
Keyword(s):  
Vaccine Coverage ◽  
Deep Understanding ◽  
World Health ◽  
Vaccine Hesitancy ◽  
Slight Reduction ◽  
Cultural Variation ◽  
Global Public Health ◽  
Factors Affecting ◽  
Wide Range ◽  
Context Specific

BACKGROUND World Health Organization declared the vaccine hesitancy as a global public health threat in 2019. Since even a slight reduction in vaccine coverage rates can lead to a decrease in herd immunity, it is imperative to explore the underlying factors affecting vaccine hesitancy. in specific contexts, considering socioeconomic and cultural variation, to ensure interventions targeting hesitancy are well formulated and intervened. OBJECTIVE The main objective of this study is to identify underlying factors affecting vaccine hesitancy in Iran. METHODS A framework qualitative study will be conducted in the west of Tehran province in 2020. Participants in the study will be recruited hesitance-parents who extracted from the SIB system (an electronic health record in Iran) to maximize diversity. Interviews will be analyzed based on ''Determinants of Vaccine Hesitancy Matrix'' which developed by the WHO-SAGE Working Group. RESULTS deep understanding from the context-specific reasons for vaccine hesitancy cause to formulate better strategies to address them. The ultimate goal of this study is to inform future policies to increase the uptake of the vaccine in Iran. CONCLUSIONS This result of study will show variety opinions about vaccination among different types of socioeconomic and demographic households. The wide range of reasons related to vaccine hesitancy imply to more comprehensive, context-specific interventions. Today, the most important intervention issues focus on improving information about effectiveness and safety of vaccines, while other interventions for promoting vaccination is need to addressed.

scholarly journals Modelling the elastic mechanical properties of bioactive glass-derived scaffolds

2020 ◽  
Vol 6 (1) ◽  
pp. 50-56
Author(s):  
Francesco Baino ◽  
Elisa Fiume
Keyword(s):  
Elastic Properties ◽  
Poisson’S Ratio ◽  
Mechanical Performance ◽  
Solid Material ◽  
Poisson's Ratio ◽  
Predictive Capability ◽  
Shear Moduli ◽  
Wide Range ◽  
Constitutive Parameters ◽  
The Relationship

AbstractPorosity is known to play a pivotal role in dictating the functional properties of biomedical scaffolds, with special reference to mechanical performance. While compressive strength is relatively easy to be experimentally assessed even for brittle ceramic and glass foams, elastic properties are much more difficult to be reliably estimated. Therefore, describing and, hence, predicting the relationship between porosity and elastic properties based only on the constitutive parameters of the solid material is still a challenge. In this work, we quantitatively compare the predictive capability of a set of different models in describing, over a wide range of porosity, the elastic modulus (7 models), shear modulus (3 models) and Poisson’s ratio (7 models) of bioactive silicate glass-derived scaffolds produced by foam replication. For these types of biomedical materials, the porosity dependence of elastic and shear moduli follows a second-order power-law approximation, whereas the relationship between porosity and Poisson’s ratio is well fitted by a linear equation.

scholarly journals An Improved Lagrangian-Inverse Method for Evaluating the Dynamic Constitutive Parameters of Concrete

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1871
Author(s):  
Xinlu Yu ◽  
Yingqian Fu ◽  
Xinlong Dong ◽  
Fenghua Zhou ◽  
Jianguo Ning
Keyword(s):  
High Speed ◽  
Inverse Method ◽  
Image Correlation ◽  
Analysis Method ◽  
Stress Strain ◽  
Optical Techniques ◽  
Element Simulation ◽  
Non Linear ◽  
Constitutive Parameters ◽  
Inverse Analysis Method

The dynamic constitutive behaviors of concrete-like materials are of vital importance for structure designing under impact loading conditions. This study proposes a new method to evaluate the constitutive behaviors of ordinary concrete at high strain rates. The proposed method combines the Lagrangian-inverse analysis method with optical techniques (ultra-high-speed camera and digital image correlation techniques). The proposed method is validated against finite-element simulation. Spalling tests were conducted on concretes where optical techniques were employed to obtain the high-frequency spatial and temporal displacement data. We then obtained stress–strain curves of concrete by applying the proposed method on the results of spalling tests. The results show non-linear constitutive behaviors in these stress–strain curves. These non-linear constitutive behaviors can be possibly explained by local heterogeneity of concrete. The proposed method provides an alternative mean to access the dynamic constitutive behaviors which can help future structure designing of concrete-like materials.

The Petrogenetic Model, an Extension of Bowen's Petrogenetic Grid

1962 ◽  
Vol 99 (6) ◽  
pp. 558-569 ◽  
Author(s):  
Peter J. Wyllie
Keyword(s):  
Experimental Data ◽  
Constant Pressure ◽  
Three Dimensional ◽  
Pore Fluid ◽  
Fluid Composition ◽  
Solid Reaction ◽  
Petrogenetic Model ◽  
Wide Range ◽  
Opposite Face ◽  
Reaction Surfaces

AbstractBowen's petrogenetic grid is a PT projection containing univariant curves for decarbonation, dehydration, and solid-solid reactions, with vapour pressure (Pf) equal to total pressure (Ps). Analysis of experimental data in the system MgO–CO2–H2O leads to an expansion of this grid. Three of the important variables in metamorphism when Pf = Ps are P, T, and variation of the pore fluid composition between H2O and CO2. These can be illustrated in a three-dimensional petrogenetic model; one face is a PT plane for reactions occurring with pure H2O, and the opposite face is a similar plane for reactions with pure CO2; these are separated by an axis for pore fluid composition varying between H2O and CO2. Superposition of the PT faces of the model provides the petrogenetic grid. The reactions within the model are represented by divariant surfaces, which may meet along univariant lines. For dissociation reactions, the surfaces curve towards lower temperatures as the proportion of non-reacting volatile increases, and solid-solid reaction surfaces are parallel to the vapour composition axis and perpendicular to the PT axes. The relative temperatures of reactions and the lines of intersections of the surfaces can be illustrated in isobaric sections. Isobaric sections are used to illustrate reactions proceeding at constant pressure with (1) pore fluid composition remaining constant during the reaction, with temperature increasing (2) pore fluid composition changing during the reaction, with temperature increasing, and (3) pore fluid changing composition at constant temperature. The petrogenetic model provides a convenient framework for a wide range of experimental data.

Impact of random soil properties on stress–strain response

2004 ◽  
Vol 41 (2) ◽  
pp. 351-355 ◽  
Author(s):  
Dieter Stolle ◽  
Peijun Guo ◽  
Gabriel Sedran
Keyword(s):  
Soil Properties ◽  
Constitutive Modelling ◽  
Soil Parameters ◽  
Strain Response ◽  
Constitutive Behaviour ◽  
Stress Strain ◽  
Deterministic Analysis ◽  
Model Predictions ◽  
Random Variability ◽  
The Impact

This paper analyzes the impact of natural random variation of soil properties on the constitutive modelling of geomaterial behaviour. A theoretical framework for accommodating variation in soil properties is presented. The framework is then used to examine the consequence of parameter variability on stress–strain relations. An important observation is that average soil parameters from a series of tests on small specimens, in which density of the specimens varies randomly, do not necessarily reflect the average constitutive behaviour of soil. Model predictions are shown to be consistent with the experimental data.Key words: random variability, deterministic analysis, soil parameters, constitutive model.

INVESTIGATING THE INFLUENCE OF ENVIRONMENTAL CONDITIONING ON EPOXY RESINS AT QUASISTATIC AND HIGH STRAIN RATES FOR MATERIAL OPERATING LIMIT

2021 ◽  
Author(s):  
SAGAR M. DOSHI, SAGAR M. DOSHI, ◽  
NITHINKUMAR MANOHARAN ◽  
BAZLE Z. (GAMA) HAQUE, ◽  
JOSEPH DEITZEL ◽  
JOHN W. GILLESPIE, JR.
Keyword(s):  
Mechanical Properties ◽  
Epoxy Resin ◽  
Yield Stress ◽  
High Strain ◽  
Operating Conditions ◽  
Strain Rates ◽  
High Strain Rates ◽  
Stress Strain ◽  
Wide Range ◽  
Environmental Aging

Epoxy resin-based composite panels used for armors may be subjected to a wide range of operating temperatures (-55°C to 76°C) and high strain rates on the order of 103-104 s-1. Over the life cycle, various environmental factors also affect the resin properties and hence influence the performance of the composites. Therefore, it is critical to determine the stress-strain behavior of the epoxy resin over a wide range of strain rates and temperatures for accurate multi-scale modeling of composites and to investigate the influence of environmental aging on the resin properties. Additionally, the characterization of key mechanical properties such as yield stress, modulus, and energy absorption (i.e. area under the stress-strain curve) at varying temperatures and moisture can provide critical data to calculate the material operating limits. In this study, we characterize mechanical properties of neat epoxy resin, SC-15 (currently used in structural armor) and RDL-RDC using uniaxial compression testing. RDL-RDC, developed by Huntsman Corporation, has a glass transition temperature of ~ 120°C, compared to ~ 85°C of SC-15. A split Hopkinson pressure bar is used for high strain rate testing. Quasistatic testing is conducted using a screw-driven testing machine (Instron 4484) at 10-3 s-1 and 10-1 s-1 strain rates and varying temperatures. The yield stress is fit to a modified Eyring model over the varying strain rates at room temperature. For rapid investigation of resistance to environmental aging, accelerated aging tests are conducted by immersing the specimens in 100°C water for 48 hours. Specimens are conditioned in an environmental chamber at 76 °C and 88% RH until they reach equilibrium. Tests are then conducted at five different temperatures from 0°C to 95°C, and key mechanical properties are then plotted vs. temperature. The results presented are an important step towards developing a methodology to identify environmental operating conditions for composite ground vehicle applications.

Development of a Methodology for Model Testing of Utor Welded Joints of a Vertical Cylindrical Tank

2021 ◽  
pp. 21-27
Author(s):  
D.A. Neganov ◽  
◽  
A.E. Zorin ◽  
O.I. Kolesnikov ◽  
G.V. Nesterov ◽  
...  
Keyword(s):  
Welded Joints ◽  
Strain State ◽  
Welded Joint ◽  
Design Parameters ◽  
Cylindrical Tank ◽  
Stress Strain ◽  
The Real ◽  
Stress Strain State ◽  
Hydraulic Machines ◽  
Wide Range

The methodology of laboratory modeling of the loading of utor welded joint of the tank is presented. The methodology is based on testing of the special design sample. It allows under uniaxial tension on the typical servo-hydraulic machines to reproduce in the zone of a utor welded joint the combined action of bending and shear forces, similar to that which occurs during the operation of a vertical cylindrical tank. To assess the distribution of the stress-strain state in the proposed design of the sample under its loading, the finite element modeling was performed in the ANSYS software package. It showed the fundamental correspondence of the stress distribution in the zone of the utor node in the sample and in the real tank. The experimental studies consisted in carrying out tests for the durability of a series of 16 samples loaded with the maximum force in the cycle, causing the calculated stresses in the zone of the welded utor node in the range of 100–200 % from the maximum permissible ones. The obtained results showed that the maximum loaded zone, where the destruction of the samples occurred, is the near-seam zone of the utor welded joint on the inside of the tank. This corresponds to the statistics of the real tank failures. It is established that the developed methodology ensures the possibility of carrying out correct resource tests of the tank utor welded joints. It is also possible to vary the stress-strain state scheme within a wide range in the area of the utor welded joint by changing the design parameters of the test sample. In compliance with the regulated welding technologies and the absence of unacceptable defects in the welded joint, the utor node has a high resource, which significantly exceeding 50 years of the tank operation.

Sign in / Sign up

Export Citation Format

Share Document