Finite element analysis of mixed-in-place (MIP) columns supporting excavations in slopes considering tension-softening

2020 ◽  
Vol 57 (6) ◽  
pp. 785-800
Author(s):  
Kamchai Choosrithong ◽  
Helmut F. Schweiger ◽  
Roman Marte
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Attractive Alternative ◽  
Structural Elements ◽  
Element Analysis ◽  
Support Measure ◽  
Bored Pile ◽  
Tension Softening ◽  
Ground Conditions ◽  
Additional Support

The use of mixed-in-place (MIP) columns can be considered as an attractive alternative to sheet pile, diaphragm or bored pile walls for supporting deep excavations, even in difficult ground conditions. In this paper, results from a numerical study based on a case history are presented, where MIP columns are used to support an excavation in a slope. The special feature of this project is that tied-back anchors were not feasible as an additional support measure because structural elements were not allowed to be installed within the neighbouring ground. Thus, the MIP columns were placed in such a way that they formed an arch, including buttresses capable of transferring the load acting on the backside of the wall into the ground. In this study, an advanced constitutive model for the MIP columns is applied to capture the development of possible cracking. Variations in geometry have been performed to investigate the potential for optimization. Finally, some analyses have been conducted to show that a design of such structures compatible with Eurocode 7 requirements is perfectly feasible by means of the finite element method.

scholarly journals Design and analysis of concrete-filled tubular flange girders under combined loading

2021 ◽  
pp. 136943322110015
Author(s):  
Rana Al-Dujele ◽  
Katherine Ann Cashell
Keyword(s):  
Finite Element ◽  
Axial Force ◽  
Failure Modes ◽  
Numerical Study ◽  
Combined Loading ◽  
Torsional Stiffness ◽  
Fe Model ◽  
Combined Effects ◽  
Element Analysis ◽  
Hollow Section

This paper is concerned with the behaviour of concrete-filled tubular flange girders (CFTFGs) under the combination of bending and tensile axial force. CFTFG is a relatively new structural solution comprising a steel beam in which the compression flange plate is replaced with a concrete-filled hollow section to create an efficient and effective load-carrying solution. These members have very high torsional stiffness and lateral torsional buckling strength in comparison with conventional steel I-girders of similar depth, width and steel weight and are there-fore capable of carrying very heavy loads over long spans. Current design codes do not explicitly include guidance for the design of these members, which are asymmetric in nature under the combined effects of tension and bending. The current paper presents a numerical study into the behaviour of CFTFGs under the combined effects of positive bending and axial tension. The study includes different loading combinations and the associated failure modes are identified and discussed. To facilitate this study, a finite element (FE) model is developed using the ABAQUS software which is capable of capturing both the geometric and material nonlinearities of the behaviour. Based on the results of finite element analysis, the moment–axial force interaction relationship is presented and a simplified equation is proposed for the design of CFTFGs under combined bending and tensile axial force.

Experimental, numerical and parametric studies on stress concentration factors of T-joints under tension

2021 ◽  
pp. 136943322110499
Author(s):  
Feleb Matti ◽  
Fidelis Mashiri
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Numerical Study ◽  
Hot Spot ◽  
Joint Models ◽  
Element Analysis ◽  
T Joints ◽  
Concentration Factors ◽  
Stress Concentration Factors ◽  
Good Agreement

This paper investigates the behaviour of square hollow section (SHS) T-joints under static axial tension for the determination of stress concentration factors (SCFs) at the hot spot locations. Five empty and corresponding concrete-filled SHS-SHS T-joint connections were tested experimentally and numerically. The experimental investigation was carried out by attaching strain gauges onto the SHS-SHS T-joint specimens. The numerical study was then conducted by developing three-dimensional finite element (FE) T-joint models using ABAQUS finite element analysis software for capturing the distribution of the SCFs at the hot spot locations. The results showed that there is a good agreement between the experimental and numerical SCFs. A series of formulae for the prediction of SCF in concrete-filled SHS T-joints under tension were proposed, and good agreement was achieved between the maximum SCFs in SHS T-joints calculated from FE T-joint models and those from the predicted formulae.

scholarly journals Modeling of Size Effects in Bending of Perforated Cosserat Plates

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Roman Kvasov ◽  
Lev Steinberg
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Numerical Study ◽  
The Finite Element Method ◽  
Classical Elasticity ◽  
Element Analysis ◽  
Plate Deformation ◽  
The Finite Element Analysis ◽  
Circular Holes ◽  
Different Shapes

This paper presents the numerical study of Cosserat elastic plate deformation based on the parametric theory of Cosserat plates, recently developed by the authors. The numerical results are obtained using the Finite Element Method used to solve the parametric system of 9 kinematic equations. We discuss the existence and uniqueness of the weak solution and the convergence of the proposed FEM. The Finite Element analysis of clamped Cosserat plates of different shapes under different loads is provided. We present the numerical validation of the proposed FEM by estimating the order of convergence, when comparing the main kinematic variables with an analytical solution. We also consider the numerical analysis of plates with circular holes. We show that the stress concentration factor around the hole is less than the classical value, and smaller holes exhibit less stress concentration as would be expected on the basis of the classical elasticity.

An Evaluation and Comparison of Models for Maximum Deflection of Stiffened Plates Using Finite Element Analysis

2007 ◽  
Vol 44 (04) ◽  
pp. 212-225
Author(s):  
Lior Banai ◽  
Omri Pedatzur
Keyword(s):  
Finite Element ◽  
Orthotropic Plate ◽  
Lateral Pressure ◽  
Stiffened Plates ◽  
Maximum Deflection ◽  
Structural Elements ◽  
The Finite Element Method ◽  
Element Analysis ◽  
The Past ◽  
Different Types

Stiffened plates form the backbone of most of a ship's structure. Today, finite element (FE) models are used to analyze the behavior of such structural elements for different types of loads. In the past, when usage of computers and FE models were not used very much, analytical analysis methods were required. Two well-known methods have been developed for analyses of stiffened plates under lateral loading (uniform pressure), based on two different models, namely, the orthotropic plate model and the grillage model. Both models can give estimations for the maximum plate deflection under uniform lateral pressure. The objective of this paper is to present the two methods, evaluate and compare the methods using the finite element method, and finally implement the methods as a computer program for quick estimations of the maximum deflection of stiffened plates. The degree of accuracy of the two methods when compared to FE is discussed in some detail.

Experimental and numerical study on stiffness and damage of glass/epoxy biaxial weft-knitted reinforced composites

2020 ◽  
pp. 073168442093844 ◽  
Author(s):  
Navid Shekarchizadeh ◽  
Reza Jafari Nedoushan ◽  
Tohid Dastan ◽  
Hossein Hasani
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Study ◽  
Unit Cell ◽  
Analytical Equation ◽  
Reinforced Composites ◽  
Element Analysis ◽  
Composite Strength ◽  
Failure Theories ◽  
Meso Scale

This paper deals with investigating the tensile characteristics of biaxial weft-knitted reinforced composites in terms of stiffness, strength and failure mechanism. The biaxial weft-knitted fabric was produced on an electronic flat knitting machine by E-glass yarns and then was impregnated with epoxy resin. Using an accurate geometrical model, the composite unit cell was designed in Abaqus software’s environment. Tensile tests were simulated in different directions on the created unit cell and the stiffness was calculated. By applying the proper failure theories, the composite strength was predicted and then critical regions of the unit cell were determined. In the next step, a micromechanical approach was also applied to estimate the same tensile features. Failure theories were also applied to predict the strength and most susceptible areas for failure phenomenon in the composite unit cell. The tensile properties of the produced composites were measured and compared with outputs of the finite element and micromechanical approaches. The results showed that the meso-scale finite element analysis approach can well predict the composite strength. In contrast, the meso-scale analytical equation model was not able to predict it acceptably because this model ignores the strain concentration. Both meso-scale finite element analysis and meso-scale analytical equation approaches predicted the similar locations for the composite failure in wale and course directions.

scholarly journals Finite Element Analysis Of Airfield Flexible Pavement

2014 ◽  
Vol 60 (3) ◽  
pp. 323-334 ◽  
Author(s):  
G. Leonardi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
3D Model ◽  
Numerical Study ◽  
Permanent Deformation ◽  
Flexible Pavement ◽  
Finite Element Code ◽  
Element Analysis ◽  
Pavement Response ◽  
The Impact

Abstract The paper presents a numerical study of an aircraft wheel impacting on a flexible landing surface. The proposed 3D model simulates the behaviour of flexible runway pavement during the landing phase. This model was implemented in a finite element code in order to investigate the impact of repeated cycles of loads on pavement response. In the model, a multi-layer pavement structure was considered. In addition, the asphalt layer (HMA) was assumed to follow a viscoelastoplastic behaviour. The results demonstrate the capability of the model in predicting the permanent deformation distribution in the asphalt layer.

scholarly journals STUDY ON NONLINEAR PAVEMENT RESPONSES OF LOW VOLUME ROADWAYS SUBJECT TO MULTIPLE WHEEL LOADS / NETIESINĖS KELIO DANGOS PRIKLAUSOMYBĖS NUO MAŽO INTENSYVUMO KELIŲ, VEIKIAMŲ DAUGKARTINĖMIS RATŲ APKROVOMIS, TYRIMAS

2011 ◽  
Vol 17 (1) ◽  
pp. 45-54 ◽  
Author(s):  
Minkwan Kim ◽  
Joo Hyoung Lee
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Asphalt Pavement ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Nonlinear Stress ◽  
Low Volume ◽  
Stress Dependent

This paper describes numerical analyses on low volume roads (LVRs) using a nonlinear three-dimensional (3D) finite element model (FEM). Various pavement scenarios are analyzed to investigate the effects of pavement layer thicknesses, traffic loads, and material properties on pavement responses, such as surface deflection and subgrade strain. Each scenario incorporates a different combination of wheel/axle configurations and pavement geomaterial properties to analyze the nonlinear behavior of thinly surfaced asphalt pavement. In this numerical study, nonlinear stress-dependent models are employed in the base and subgrade layers to properly characterize pavement geomaterial behavior. Finite element analysis results are then described in terms of the effects of the asphalt pavement thickness, wheel/axle configurations, and geomaterial properties on critical pavement responses. Conclusions are drawn by the comparison of the nonlinear pavement responses in the base and subgrade in association with the effects of multiple wheel/axle load interactions. Santrauka Straipsnyje aprašoma skaitinė mažo intensyvumo kelių analizė, taikant netiesinį—erdvinį baigtinių elementų modelį. Skirtingi dangų paviršiaus variantai analizuojami siekiant ištirti, kokiąįtaką kelio dangos elgsenai, t. y. poslinkiams ir kelio pagrindo deformacijoms, turi dangų sluoksnių storiai, eismo apkrovos ir medžiagų savybės. Kiekvienas kelio dangos variantas turi skirtingas ratų arba ašies ir geometrinių savybių formas, kad būtų galima išanalizuoti netiesinę plonos asfalto dangos paviršiaus elgseną. Šioje skaitinėje analizėje nagrinėjami netiesiniai įtempių modeliai, kurie buvo taikomi pagrindo sluoksniams, siekiant tinkamai apibūdinti geometrinę kelio dangos elgseną. Baigtinių elementų analizės rezultatai toliau nagrinėjami atsižvelgiant į asfalto dangos storį ar ašies formą ir geometrines savybes, priklausomai nuo kritinės kelio dangos būklės. Išvados buvo gautos lyginant netiesines kelių dangos priklausomybes pagrindo sluoksnyje, atsižvelgiant į jų sąveiką su daugkartine ratų apkrova.

Sign in / Sign up

Export Citation Format

Share Document