Evaluation of rheological behavior and performance to permanent deformation of nanomodified asphalt mixtures with carbon nanotubes

2016 ◽  
Vol 43 (5) ◽  
pp. 472-479 ◽  
Author(s):  
João Victor Staub de Melo ◽  
Glicério Trichês
Keyword(s):  
Carbon Nanotubes ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixtures ◽  
Asphalt Pavements ◽  
Accelerated Degradation ◽  
Wheel Tracking Test ◽  
And Performance ◽  
Wheel Tracking ◽  
Reference Mixture

Rutting is one of the most important issues associated with asphalt pavements. This defect leads to the accelerated degradation of the pavement and considerably reduces the level of road safety. This paper reports on the results obtained in the optimization of nanocomposite asphalt containing carbon nanotubes (CNTs) with regard to the resistance to permanent deformation. Nanocomposite asphalts were prepared with the addition of different proportions of CNTs. Based on a study on the empirical and rheological properties of the nanocomposites developed, optimization of the CNT content incorporated into the conventional asphalt binder was carried out. Then two asphalt mixtures were investigated, a reference mixture and a nanomodified mixture with CNTs (optimal content). The rheological evaluations were carried out on four-point fatigue equipment and the resistance to permanent deformation was tested in a traffic simulator (wheel tracking test). The results demonstrate the efficient contribution of the nanocomposite to the resistance to permanent deformation.

Pavement Performance of Hot In-Place Recycling for Waste Asphalt Mixtures

2013 ◽  
Vol 668 ◽  
pp. 292-296
Author(s):  
Ya Li Ye ◽  
Chuan Yi Zhuang ◽  
Jia Bo Hu
Keyword(s):  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Asphalt Pavements ◽  
Pavement Performance ◽  
Test Results ◽  
Technical Parameters ◽  
Stable Performance ◽  
Wheel Tracking Test ◽  
Asphalt Content ◽  
Wheel Tracking

With the early asphalt pavements have been into the stage of medium maintenance or overhaul, recycling is a very important way for waste asphalt mixtures. A sample was taken in the expressway from Huhhot to Baotou, and the waste mixtures were extracted from field and sieved; so that the new aggregates can be determined and mix design was carried. With the aid of the penetration, the softening point and the viscosity in 135°C test, the quantity of the regenerant and the asphalt content were ascertained. Through the high temperature stable performance, the anti-low temperature performance, the water stability and the Hamburg wheel-tracking test, the appropriate gradation and the optimum asphalt content were determined. The test results showed that the pavement performance of the waste asphalt mixture was enhanced obviously with hot in-place recycling, and it has achieved technical parameters for old asphalt mixture.

scholarly journals Performance Analysis of Asphalt Mixtures Modified with Ground Tire Rubber Modifiers and Recycled Materials

2019 ◽  
Vol 11 (6) ◽  
pp. 1792 ◽  
Author(s):  
Punyaslok Rath ◽  
Joshua Love ◽  
William Buttlar ◽  
Henrique Reis
Keyword(s):  
Compact Tension ◽  
Asphalt Mixtures ◽  
Asphalt Pavements ◽  
Tire Rubber ◽  
Ground Tire Rubber ◽  
Reclaimed Asphalt ◽  
Dry Process ◽  
Polymer Hybrid ◽  
And Performance ◽  
Wheel Tracking

The usage of Ground Tire Rubber (GTR) in asphalt pavements has gained renewed interest due to its potential sustainability, economic, and performance benefits. This study focuses on asphalt mixtures designed with three different rubber modifier products including (1) a terminal-blend GTR, (2) a dry-process, chemically processed rubber product, and (3) a terminal-blend rubber-polymer hybrid product. The modifications were incorporated into Illinois Tollway’s approved Stone Matrix Asphalt (SMA) designs using (1) a base binder (PG 58-28), (2) a softer binder (PG 46-34), and (3) a softer binder with higher recycled content. Disk-shaped Compact Tension (DC(T)) test, Hamburg Wheel Tracking Test (HWTT) and Acoustic Emission (AE) tests were performed to characterize the mixtures. The fracture energy for most mixtures met the stringent criteria of 690 J/m2 and the rut depths measured were less than 6 mm at 20,000 wheel passes. A Hamburg-DC(T) plot suggests that higher amounts of RAP/RAS (RAP: Reclaimed Asphalt Pavement; RAS: Reusable Asphalt Shingles) can be successfully used if a suitably soft base binder is employed.

Relating Adhesion and Cohesion of Asphalts to the Effect of Moisture on Laboratory Performance of Asphalt Mixtures

2005 ◽  
Vol 1901 (1) ◽  
pp. 33-43 ◽  
Author(s):  
Kunnawee Kanitpong ◽  
Hussain Bahia
Keyword(s):  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Fundamental Properties ◽  
Water Conditioning ◽  
Before And After ◽  
Indirect Tensile ◽  
Wheel Tracking

Antistripping additives and polymer modifications are two common modifiers used to improve the fundamental properties of asphalt binders as those properties relate to the performance of asphalt mixtures. Adhesion and cohesion are two important related properties of asphalt binders that can affect asphalt mixture performance before and after water conditioning. The purpose of this study was to quantify the effects of antistripping additives and polymers on the adhesion and cohesion of binders and to relate these effects to the performance of mixtures as measured in the laboratory before and after water conditioning. The performance tests of asphalt mixtures included indirect tensile strength, uniaxial compression permanent deformation, and Hamburg wheel tracking. Asphalt mixtures were produced with different modified binders and with two aggregate types. The binders were modified with antistripping additives and polymers and by chemical treatment and oxidization methods. Granite and limestone were selected as two types of aggregate sources. The results indicate that the performance of asphalt mixtures is highly dependent on modification techniques and water conditioning. The overall performance of polymer-modified mixtures is more desirable than those of unmodified mixtures and of mixtures modified with antistripping additives. Polymers are found to improve rutting performance, adhesion, and cohesion of an asphalt binder. In contrast, the antistripping additive can improve only the adhesion without changing other properties. The results of this study also illustrate that the adhesion and cohesion of an asphalt binder are good indicators of the performance of asphalt mixtures in the laboratory when they are conditioned with water.

scholarly journals Carbon Nanotubes (CNTs) in Asphalt Binder: Homogeneous Dispersion and Performance Enhancement

2018 ◽  
Vol 8 (12) ◽  
pp. 2651 ◽  
Author(s):  
Muhammad Haq ◽  
Naveed Ahmad ◽  
Muhammad Nasir ◽  
Jamal ◽  
Murryam Hafeez ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Performance Enhancement ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Strength Properties ◽  
Adhesion Properties ◽  
Traffic Volumes ◽  
And Performance ◽  
Mixing Techniques

Conventional binders cannot meet the current performance requirements of asphaltic pavements due to increase in traffic volumes and loads. Nanomaterials, due to their exceptional mechanical properties, are gaining popularity as bitumen modifiers to enhance the performance properties of the asphaltic concrete. Carbon Nanotubes (CNTs) are one of the most widely used nanomaterials because of their strength properties, light weight, small size, and large surface area. CNT addition results in improved substrate characteristics as compared to other modifiers. Due to high length to diameter ratio, dispersion of CNTs in bitumen is a complex phenomenon. In this study, dispersion of CNTs in bitumen was carried out using both dry and wet mixing techniques, the latter was selected on the basis of homogeneity of the resultant asphalt mixture. Scanning Electron Microscopy (SEM) was used to check the dispersion of CNTs in binder while Fourier Transform Infrared Spectroscopy (FTIR) was carried out to ensure the removal of solvent used for wet mixing. Conventional bitumen tests (penetration, softening point, and ductility), dynamic shear rheometer tests, rolling bottle tests, and bitumen bond strength tests were employed to check the improvement in the rheological and adhesion properties of bitumen while wheel tracker test was used to check the improvement in resistance against permanent deformation of asphalt mixtures after addition of CNTs. Results show that CNTs improved the higher temperature performance and permanent deformation resistance in both binder and mixtures. Improvement in bitumen–aggregate adhesion properties and moisture resistance was also observed.

Laboratory Study on the Effect of Asphalt Emulsion as a Rejuvenator in Aged Asphalt Pavement

2012 ◽  
Vol 587 ◽  
pp. 57-61
Author(s):  
Rashid Tanzadeh ◽  
Mahyar Arabani
Keyword(s):  
Asphalt Pavement ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixtures ◽  
Asphalt Pavements ◽  
Laboratory Research ◽  
Asphalt Emulsion ◽  
Aged Asphalt ◽  
Repeated Load ◽  
Penetration Tests

Modification of the asphalt binder is one approach taken to improve aged pavement performance. To make the most of maintenance budgets, many agencies have resorted to the use of asphalt rejuvenators as an alternative to revive aging and brittle asphalt pavements. The purpose of this study is laboratory research on the effect of asphalt emulsion in restoring the original properties of aged asphalt pavement. For this purpose, the repeated load axial test is carried out on conventional asphalt samples and aged asphalt samples containing rejuvenator agents in different stress and rejuvenator percentage. Bitumen aged with RTFO according to ASTM-D2872 and the optimum bitumen of 5.5% were considered. The softening point and penetration tests, to examine the effect of rejuvenator in asphalt mixtures modification, On the basic, aged and modified aged bitumen were performed. The results represent that asphalt emulsion as a rejuvenator material in aged asphalt samples because of suitable performance improve aged asphalt permanent deformation resistance and aged bitumen Rheological property.

Laboratory Study on the Effect of Nano TiO2 on Rutting Performance of Asphalt Pavements

2012 ◽  
Vol 622-623 ◽  
pp. 990-994 ◽  
Author(s):  
Javad Tanzadeh ◽  
Fariborz Vahedi ◽  
Pezhouhan T. Kheiry ◽  
Rashid Tanzadeh
Keyword(s):  
Dynamic Loading ◽  
Laboratory Study ◽  
Hot Mix Asphalt ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Asphalt Pavements ◽  
Pavement Performance ◽  
Laboratory Research ◽  
Wheel Tracking Test ◽  
Wheel Tracking

Modification of the asphalt binder is one approach taken to improve Asphalt pavement performance. Rutting is one of the most important factors that could reduce the life of asphalt pavements.Nowadays, the application of nanotechnologyto achieve materials that are more resistant is expanding in asphalt pavement thatNano-TiO2is among the most exciting and promising classes of materials discovered recently. The purpose of this study is laboratory research on the effect of Nano-TiO2in improving Bitumen property and rutting resistance in Asphalt pavement under dynamic loading. For this purpose, the wheel-tracking test was carried outon ordinary and Nano-TiO2modified hot mix asphalt samples.The results illustrate that using Nano-TiO2in asphaltbinder samples cause to an improvement in ruttingdepth in comparison with theordinarymixtures.

scholarly journals Impact of the Superpave hot mix asphalt properties on its permanent deformation behavior

2018 ◽  
Vol 162 ◽  
pp. 01041
Author(s):  
Zahra Qasim ◽  
Alaa Abed ◽  
Zaynab Qasim
Keyword(s):  
Asphalt Concrete ◽  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Asphalt Pavements ◽  
Compaction Temperature ◽  
Factors Affecting ◽  
Concrete Mixtures ◽  
Pavement Performance Prediction ◽  
Wheel Tracking ◽  
Sbs Modified Asphalt

In Iraq, the severity of rutting has increased in asphalt pavements possibly due to the increase in truck axle loads, tyre pressure, and high pavement temperature in summer. As of late, Superpave has been accounted as an enhanced system for performance based design, analysis of asphalt pavement performance prediction for asphalt concrete mixes. In this research the development of permanent deformation in asphalt concrete under repeated loadings was investigated, Wheel-Tracking apparatus has been used in a factorial testing program during which 44 slab samples were tested to simulate actual pavement. The objectives of the present research include; investigating the main factors affecting rutting in asphalt concrete mixture, quantifying the effect of SBS polymer and steel reinforcement on asphalt concrete mixtures in addition to studying the effect of variables on the asphalt concrete mixes against moisture sensitivity. It has been determined that that increasing of compaction temperature from 110 to 150°C will decrease the permanent deformation by 20.5 and 15.6 percent for coarse and fine gradation control asphalt mixtures, respectively. While the permanent deformation decreases by 21.3 percent when the compaction temperature is increased from 110 to 150°C for coarse gradation SBS modified asphalt mixtures.

Performance of Asphalt Mixture Used for Asphalt Treated Base of Perpetual Pavements

2011 ◽  
Vol 415-417 ◽  
pp. 1531-1536
Author(s):  
Fu Ming Liu ◽  
Duan Yi Wang
Keyword(s):  
Tensile Strain ◽  
Performance Test ◽  
Asphalt Mixture ◽  
Fatigue Tests ◽  
Asphalt Pavements ◽  
Moisture Susceptibility ◽  
Scale Test ◽  
And Performance ◽  
Wheel Tracking ◽  
Fatigue Endurance

This paper presents the results of laboratory and performance tests for an asphalt treated base (ATB) and mixes developed in this study for perpetual asphalt pavements. Laboratory tests for the mixes included moisture susceptibility, wheel tracking and fatigue tests. The results of performance test indicated that the resistances of the high content binder ATB against moisture and fatigue damage were better than those of the lower one. It was also found from the full scale test sections that the tensile strain values at the bottom of the asphalt layer for the ATB sections were low when the asphalt layer thicknesses of the ATB sections were not thicker than those of the conventional sections. All the tensile strain values measured from the ATB sections were within the fatigue endurance limit of 70 microstrain which is the fatigue criterion of a perpetual asphalt pavement.

Determining Optimum Carbon Nanotubes Content for Asphalt Mixture in Road Pavements

2021 ◽  
Vol 1023 ◽  
pp. 121-126
Author(s):  
Van Bach Le ◽  
Van Phuc Le
Keyword(s):  
Carbon Nanotubes ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Construction Cost ◽  
Asphalt Mixtures ◽  
Static Modulus ◽  
Pavement Construction ◽  
Modified Binder ◽  
Marshall Stability

Although small amount of binder in asphalt concrete mixture may commonly range from 3.5 to 5.5% of total mixture as per many international specifications, it has a significant impact on the total cost of pavement construction. Therefore, this paper investigated the effects of five carbon nanotubes contents of 0.05%, 0.1%, 0.15%, 0.2%, 0.25% by asphalt weight as an additive material for binder on performance characteristics of asphalt mixtures. Performance properties of CNTs modified asphalt mixtures were investigated through the Marshall stability (MS) test, indirect tensile (IDT) test, static modulus (SM) test, wheel tracking (WT) test. The results indicated that asphalt mixtures with CNT modified binder can improve both the rutting performance, IDT strength and marshall stability of tested asphalt mixtures significantly at higher percentages of carbon nanotubes. However, the issue that should be considered is the construction cost of asphalt pavement. Based on the asphalt pavement structural analysis and construction cost, it can be concluded that an optimum CNT content of 0.1% by asphalt weight may be used as additive for asphalt binder in asphalt mixtures.

Effectiveness of Loaded Wheel Tracking Test to Ascertain Moisture Susceptibility of Asphalt Mixtures

2021 ◽  
pp. 036119812110363
Author(s):  
Moses Akentuna ◽  
Louay N. Mohammad ◽  
Sanchit Sachdeva ◽  
Samuel B. Cooper ◽  
Samuel B. Cooper
Keyword(s):  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Moisture Damage ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Creep Recovery ◽  
Moisture Susceptibility ◽  
Freeze Thaw ◽  
Wheel Tracking ◽  
Mixture Samples

Moisture damage of asphalt mixtures is a major distress affecting the durability of asphalt pavements. The loaded wheel tracking (LWT) test is gaining popularity in determining moisture damage because of its ability to relate laboratory performance to field performance. However, the accuracy of LWT’s “pass/fail” criteria for screening mixtures is limited. The objective of this study was to evaluate the capability of the LWT test to identify moisture susceptibility of asphalt mixtures with different moisture conditioning protocols. Seven 12.5 mm asphalt mixtures with two asphalt binder types (unmodified PG 67-22 and modified PG 70-22), and three aggregate types (limestone, crushed gravel, and a semi-crushed gravel) were utilized. Asphalt binder and mixture samples were subjected to five conditioning levels, namely, a control; single freeze–thaw-; triple freeze–thaw-; MiST 3500 cycles; and MiST 7000 cycles. Frequency sweep at multiple temperatures and frequencies, and multiple stress creep recovery tests were performed to evaluate asphalt binders. LWT test was used to evaluate the asphalt mixture samples. Freeze–thaw and MiST conditioning resulted in an increase in stiffness in the asphalt binders as compared with the control. Further, freeze–thaw and MiST conditioning resulted in an increase in rut depth compared with the control asphalt mixture. The conditioning protocols evaluated were effective in exposing moisture-sensitive mixtures, which initially showed compliance with Louisiana asphalt mixture design specifications.

Sign in / Sign up

Export Citation Format

Share Document