A preliminary study of the mechanical properties of asphalt mixture containing bottom ash

2008 ◽  
Vol 35 (10) ◽  
pp. 1114-1119 ◽  
Author(s):  
Shu Wei Goh ◽  
Zhanping You
Keyword(s):  
Mechanical Properties ◽  
Dynamic Modulus ◽  
Permanent Deformation ◽  
Bottom Ash ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Test Results ◽  
Flow Number ◽  
Preliminary Study ◽  
Primary Focus

This paper shows a preliminary study of asphalt mixtures containing bottom ash with a primary focus on the permanent deformation. The objectives of this study are (i) perform literature reviews on the mechanical properties of asphalt mixtures containing bottom ash; (ii) evaluate the effects of using bottom ash as the mineral filler for the asphalt mixture through the flow number and dynamic modulus tests; and (iii) use the test results to evaluate the pavement permanent deformation using the Mechanistic–empirical pavement design guide (MEPDG) analysis. It was found that the asphalt mixture using bottom ash uses higher asphalt content due to the higher absorption. The replacement with bottom ash in the asphalt mixture generates a lower dynamic modulus as compared to the control mixtures. Additionally, results from MEPDG analysis show mixtures with bottom ash have higher rutting potential.

scholarly journals Effectiveness of Micro- and Nanomaterials in Asphalt Mixtures through Dynamic Modulus and Rutting Tests

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Hui Yao ◽  
Zhanping You
Keyword(s):  
Dynamic Modulus ◽  
Mechanical Performance ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Asphalt Binders ◽  
Test Results ◽  
Modified Asphalt ◽  
Overall Performance ◽  
Carbon Microfiber

The objectives of this research are to use micro- and nanomaterials to modify the asphalt mixture and to evaluate the mechanical performance of asphalt mixtures. These micro- and nanomaterials, including carbon microfiber, Nanomer material, nanosilica, nonmodified nanoclay, and polymer modified nanoclay, were selected to blend with the control asphalt to improve the overall performance of the modified asphalt binders and mixtures. The microstructures of original materials and asphalt binders were observed by the field emission scanning electron microscope (FE-SEM). The mixture performance tests were employed to evaluate the resistance to rutting and permanent deformation of the modified asphalt mixtures. Test results indicate that(1)the dynamic modulus of micro- and nanomodified asphalt mixtures improved significantly;(2)the rutting susceptibility of the modified asphalt mixtures was reduced significantly compared to that of the control asphalt mixture;(3)the microstructures of modified asphalt binders were different from the control asphalt, and the structures determine the improvement in the performance of modified asphalt mixtures. These results indicate that the addition of micro- and nanomaterials enhanced the rutting performance and strength of asphalt mixtures. In addition, the analysis of variance (ANOVA) was used to analyze the modifying effects of micro- and nanomaterials on the performance.

Rheological Properties of High Grade Asphalt and its Mixture

2014 ◽  
Vol 599 ◽  
pp. 244-247 ◽  
Author(s):  
Qun Shan Ye ◽  
Chang Jian Ye ◽  
Zhi Lin Sun
Keyword(s):  
Rheological Properties ◽  
Dynamic Modulus ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Asphalt Binders ◽  
Test Results ◽  
Complex Shear Modulus ◽  
Complex Shear ◽  
Dynamic Modulus Test

Viscosity test, dynamic shear test, dynamic modulus test and creep test were conducted to investigate the rheological properties of high modulus asphalt and its mixture. Test results indicated that the viscosity of hard grade asphalt could be increased when compared with the ordinary asphalt, especially at high temperatures. The complex shear modulus and dynamic modulus of hard-grade asphalt binder and its mixture were increased, which implied that the stiffness of them was enhanced. Furthermore, the elastically portions for viscoelastic property of asphalt binders were increased, which resulted in the reduction of phase angle for hard grade asphalt binders and mixtures. The rutting parameter for hard-grade asphalt mixture was increased remarkably, which revealed that the resistance to permanent deformation could be significantly improved for hard grade asphalt mixture.

scholarly journals The Potential use of Crumb Rubber in Hot Asphalt Mixes in Egypt using Dry Process

2019 ◽  
Vol 9 (1) ◽  
pp. 4356-4360
Keyword(s):  
Mechanical Properties ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Road Construction ◽  
Crumb Rubber ◽  
Flow Number ◽  
Storage Container ◽  
Dry Process ◽  
Wet Process ◽  
Process Method

Since 1960 Using crumb rubber modifier (CRM) in hot asphalt mixtures has become a frequent practice in road construction. Using the CRM by the dry process method is not commonly used, although it has great advantages such as it is less fuel consuming and it does not require storage container like the wet process method. This research evaluates the mechanical properties of dense graded asphalt rubber mixtures manufactured using the dry process. The results obtained from this mixture compared with similar asphalt mixture without CRM. The mechanical properties of all mixtures evaluated using a set of tests such Marshall Stability and flow test, moisture susceptibility test, indirect tensile strength test, dynamic modulus and flow number test. The research results showed that using CRM with 0.75% of aggregate’s weight increased the mixture’s stability, flow and enhanced its cracking and permanent deformation resistance.

Research of Mechanical Properties of Asphalt Pavement Materials with WMA and RAP

2012 ◽  
Vol 204-208 ◽  
pp. 3934-3937 ◽  
Author(s):  
Bao Yang Yu ◽  
Yu Wang ◽  
Min Jiang Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Dynamic Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Porous Asphalt ◽  
Compaction Energy ◽  
Indirect Tensile

The objectives of this paper are to characterize the mechanical properties of porous asphalt pavement mixtures containing RAP and a WMA additive using Super pave gyratory compactor and dynamic modulus testing. Four types of asphalt mixtures were evaluated in this study. This study evaluated compaction energy index, permeability, indirect tensile strength, and dynamic modulus for all types of porous asphalt mixtures. All of the asphalt mixtures meet the typical minimum coefficient of permeability in this study. In addition, only a slight decrease in was found when WMA additive was added to the porous asphalt mixture containing RAP. For indirect tensile strength testing, WMA containing RAP was found to have the highest tensile strength among all of the mixtures tested.

Study on Dynamic Modulus of Waste Plastic Modified Asphalt Mixture Using Waste Plastic Bag Chips

2011 ◽  
Vol 261-263 ◽  
pp. 824-828 ◽  
Author(s):  
Qian Zhang ◽  
Shu Wei Goh ◽  
Zhan Ping You
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Control Sample ◽  
Asphalt Mixtures ◽  
Test Results ◽  
Waste Plastic ◽  
Modified Asphalt ◽  
Plastic Bag ◽  
Dynamic Modulus Test

The objective of this study is to investigate the possibility of using waste plastic as an additive to modify asphalt mixtures thereby reducing the waste plastic stream in our environment. High density polyethylene plastic bags obtained from the retail store were shredded into chips and added into asphalt mixtures at the rate of 0% (control sample), 2, 5 and 8% based on binder weight. Three different temperatures of 4, 21.3 and 39.2°C and frequencies ranging from 0.1 to 25 Hz were used in the dynamic modulus test. It was found that most of the asphalt mixtures modified with waste plastic have higher dynamic modulus when compared with the control samples. However, no significant trend on phase angle was found among all the samples tested based on the test results. In this study, it was found that the modified asphalt mixture with 2% waste plastic had the highest dynamic modulus and phase angle. Based on the test results, it was found that plastic modified asphalt mixture will have a better performance under intermediate and high temperature conditions.

scholarly journals Influence of compaction temperature on the properties of Marshall specimens

2015 ◽  
Vol 10 (4) ◽  
pp. 309-315 ◽  
Author(s):  
Ivica Androjić ◽  
Sanja Dimter
Keyword(s):  
Mechanical Properties ◽  
Structural Design ◽  
Hot Mix Asphalt ◽  
Asphalt Mixture ◽  
Maximum Density ◽  
Asphalt Mixtures ◽  
Test Results ◽  
Compaction Temperature ◽  
Asphalt Mix ◽  
Very High

Compaction of hot mix asphalt is influenced by several factors; some related to the environment, some determined by mix and structural design and some by contractor during construction. The temperature of asphalt mixture has the biggest influence on the compaction of asphalt mixtures and their properties. The temperature of asphalt mixture affects viscosity of bitumen and achievement of the maximum density of asphalt mixture. This paper describes a laboratory study on the effects of different installation temperatures on the physico-mechanical properties of specimens of asphalt mixtures: stability, Marshall Quotient (stiffness), density, voids and voids filled with asphalt. By regression analysis of the test results the correlation of certain properties of asphalt mix and compaction temperatures was established. For all the models observed, the coefficients of determination are very high and indicate very solid links. The obtained research results indicate a pronounced effect of compaction temperature on each tested property of asphalt mix.

scholarly journals Functional and environmental performance of plant-produced crumb rubber asphalt mixtures using the dry process

2021 ◽  
Vol 54 (5) ◽  
Author(s):  
M. Bueno ◽  
R. Haag ◽  
N. Heeb ◽  
P. Mikhailenko ◽  
L. Boesiger ◽  
...  
Keyword(s):  
Environmental Performance ◽  
High Performance ◽  
Large Scale ◽  
Fatigue Behavior ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Asphalt Mixtures ◽  
Gaseous Emissions ◽  
Dry Process

AbstractIncorporating crumb rubber (CR) using the dry process, directly in the asphalt mixture rather than into the bituminous binder requires no plant retrofitting, and therefore is the most practical industrial method for CR incorporation into asphalt mixtures. Nevertheless, very few large scale studies have been conducted. This work uses a holistic approach and reports on the functional and environmental performance of asphalt mixtures with different concentrations of CR fabricated employing the dry process in asphalt plants. Gaseous emissions were monitored during the production and laboratory leaching tests simulating the release of pollutants during rain, was conducted to evaluate the toxicology of both the CR material alone and the modified asphalt mixtures. In addition, laboratory compacted samples were tested to assess their fatigue behavior. Furthermore, noise relevant surface properties of large roller compacted slabs were evaluated before and after being subjected to a load simulator (MMLS3) to evaluate their resistance to permanent deformation. The results confirm that comparable performance can be achieved with the incorporation of CR using the dry process for high performance surfaces such as semi-dense asphalt, which usually require the use of polymer modified binders. Environmental performance improvement can be achieved by a washing step of the CR material that could remove polar CR additives which have commonly been used as vulcanization accelerator during rubber production.

Experimental Analysis of Dynamic Modulus and Phase Angle of High Modulus Asphalt Mixture

2011 ◽  
Vol 243-249 ◽  
pp. 4220-4225
Author(s):  
Rui Bo Ren ◽  
Li Tao Geng ◽  
Li Zhi Wang ◽  
Peng Wang
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Performance Testing ◽  
Asphalt Mixtures ◽  
Testing System ◽  
High Modulus ◽  
Temperature Performance ◽  
Different Temperatures ◽  
Confining Pressures

To study the mechanical properties of high modulus asphalt mixtures, dynamic modulus and phase angle of these two mixtures are tested with Simple Performance Testing System under different temperatures, loading frequencies and confining pressures. Testing results show the superiority of high modulus asphalt mixture in aspect of high temperature performance. Furthermore, the changing rules of dynamic modulus and phase angle are also discussed.

scholarly journals Viscoelastic Parameters of Asphalt Mixtures Identified in Static and Dynamic Tests

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2084 ◽  
Author(s):  
Piotr Mackiewicz ◽  
Antoni Szydło
Keyword(s):  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Dynamic Test ◽  
Asphalt Mixtures ◽  
Rheological Parameters ◽  
Dynamic Tests ◽  
Static Test ◽  
Viscoelastic Parameters ◽  
Static Creep ◽  
Asphalt Content

We present two methods used in the identification of viscoelastic parameters of asphalt mixtures used in pavements. The static creep test and the dynamic test, with a frequency of 10 Hz, were carried out based on the four-point bending beam (4BP). In the method identifying viscoelastic parameters for the Brugers’ model, we included the course of a creeping curve (for static creep) and fatigue hysteresis (for dynamic test). It was shown that these parameters depend significantly on the load time, method used, and temperature and asphalt content. A similar variation of parameters depending on temperature was found for the two tests, but different absolute values were obtained. Additionally, the share of viscous deformations in relation to total deformations is presented, on the basis of back calculations and finite element methods. We obtained a significant contribution of viscous deformations (about 93% for the static test and 25% for the dynamic test) for the temperature 25 °C. The received rheological parameters from both methods appeared to be sensitive to a change in asphalt content, which means that these methods can be used to design an optimal asphalt mixture composition—e.g., due to the permanent deformation of pavement. We also found that the parameters should be determined using the creep curve for the static analyses with persistent load, whereas in the case of the dynamic studies, the hysteresis is more appropriate. The 4BP static creep and dynamic tests are sufficient methods for determining the rheological parameters for materials designed for flexible pavements. In the 4BP dynamic test, we determined relationships between damping and viscosity coefficients, showing material variability depending on the test temperature.

Sign in / Sign up

Export Citation Format

Share Document