Mechanism of shear transfer in a reinforced concrete beam

1999 ◽  
Vol 26 (6) ◽  
pp. 810-817 ◽  
Author(s):  
Akin A Olonisakin ◽  
Scott DB Alexander
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Plastic Hinge ◽  
Failure Surface ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Shear Transfer ◽  
Arching Action ◽  
Wide Beams

This paper presents an analysis of the results of five tests conducted on four reinforced concrete beams. The tests were performed principally to investigate the mechanics of internal shear transfer in a transversely loaded concrete beam with no shear reinforcement. Test specimens consisted of simply supported wide beams with steel flexural reinforcement. The reinforcement for two of the beams was epoxy coated. The shear span to depth ratios were 2.93, 3.32, and 3.81. Measured strains on the reinforcement were used to divide the total shear into its beam and arching action components. In all tests, beam and arching action shear transfer mechanisms were found to coexist. Apart from that with the longest span, all tests ended with rupture of the concrete along a diagonal failure surface. It is concluded that shear failure may be caused by a shift in the internal mechanics of shear transfer from beam action to arching action. Because this shift may be initiated by the yielding of reinforcement, it can be associated with the formation of a plastic hinge. There was no observed effect on the mechanics of shear transfer that could be attributed to epoxy coating of the reinforcement.Key words: arching action, beam action, one-way shear, shear transfer, reinforced concrete beam, bond forces, bar force gradient.

Estimation of Ultimate Tendon Stress in Reinforced Concrete Beams Prestressed with External FRP Tendons

2013 ◽  
Vol 798-799 ◽  
pp. 374-377
Author(s):  
Shuan Jiang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Plastic Hinge ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Stress Increment ◽  
Hinge Zone ◽  
Good Agreement

The ultimate tendon stress is the key to calculation of flexural capacity in reinforced concrete beam prestressed with external FRP tendons (RCBPEFT). Based on the theory of equivalent plastic hinge zone, the general formulas for calculating the ultimate tendon stress increment and ultimate tendon stress in RCBPEFT are therefore proposed. Comparisons indicate that the predictions are in good agreement with the test results.

scholarly journals Damage Evaluation in Shear-Critical Reinforced Concrete Beam using Piezoelectric Transducers as Smart Aggregates

2015 ◽  
Vol 5 (1) ◽  
Author(s):  
Constantin E. Chalioris ◽  
Nikos A. Papadopoulos ◽  
Georgia M. Angeli ◽  
Chris G. Karayannis ◽  
Asterios A. Liolios ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Reinforced Concrete Beam ◽  
Piezoelectric Transducers ◽  
Reinforced Concrete Beams ◽  
Structural Safety ◽  
Shear Span ◽  
Externally Bonded ◽  
Diagonal Crack

AbstractDamage detection at early cracking stages in shear-critical reinforced concrete beams, before further deterioration and their inevitable brittle shear failure is crucial for structural safety and integrity. The effectiveness of a structural health monitoring technique using the admittance measurements of piezoelectric transducers mounted on a reinforced concrete beam without shear reinforcement is experimentally investigated. Embedded “smart aggregate” transducers and externally bonded piezoelectric patches have been placed in arrays at both shear spans of the beam. Beam were tested till total shear failure and monitored at three different states; healthy, flexural cracking and diagonal cracking. Test results showed that transducers close to the critical diagonal crack provided sound and graduated discrepancies between the admittance responses at the healthy state and thedamage levels.Damage assessment using statistical indices calculated from the measurements of all transducers was also attempted. Rational changes of the index values were obtained with respect to the increase of the damage. Admittance responses and index values of the transducers located on the shear span where the critical diagonal crack formed provided cogent evidence of damage. On the contrary, negligible indication of damage was yielded by the responses of the transducers located on the other shear span, where no diagonal cracking occurred.

Study on Shear Resistance and Durability of CFRP Reinforced Concrete Beams

2013 ◽  
Vol 351-352 ◽  
pp. 1714-1717
Author(s):  
Shuang Chen
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Shear Failure ◽  
Concrete Beams ◽  
Shear Resistance ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Test Beam ◽  
Shear Bearing Capacity ◽  
Chlorine Ion

Through carrying capacity test of CFRP strengthened test beam and unstrengthened comparison beam under corrosion of chlorine ion, thispaper analyzes the shear resistance and durability of CFRP repaired and strengthened concrete beam. Crack generation, deflection, electrochemical index and deformation of reinforced concrete beam under service are comparedand analyzed. It is indicated that CFRP can play a favorable screening role and can effectively prevent crack development. There is no shear failure after load is applied. So CFRP can obviously improve the shear bearing capacity and durability of reinforced concrete beam. Besides, different strengthening methods have relatively obvious influence of its durability.

scholarly journals Influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams

2018 ◽  
Vol 21 (13) ◽  
pp. 1977-1989 ◽  
Author(s):  
Tengfei Xu ◽  
Jiantao Huang ◽  
Arnaud Castel ◽  
Renda Zhao ◽  
Cheng Yang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Natural Frequencies ◽  
Concrete Beams ◽  
Dynamic Stiffness ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Reinforcing Bar ◽  
Sustained Loading ◽  
Inertia Model

In this article, experiments focusing at the influence of steel–concrete bond damage on the dynamic stiffness of cracked reinforced concrete beams are reported. In these experiments, the bond between concrete and reinforcing bar was damaged using appreciate flexural loads. The static stiffness of cracked reinforced concrete beam was assessed using the measured load–deflection response under cycles of loading and unloading, and the dynamic stiffness was analyzed using the measured natural frequencies with and without sustained loading. Average moment of inertia model (Castel et al. model) for cracked reinforced beams by taking into account the respective effect of bending cracks (primary cracks) and the steel–concrete bond damage (interfacial microcracks) was adopted to calculate the static load–deflection response and the natural frequencies of the tested beams. The experimental results and the comparison between measured and calculated natural frequencies show that localized steel–concrete bond damage does not influence remarkably the dynamic stiffness and the natural frequencies both with and without sustained loading applied. Castel et al. model can be used to calculate the dynamic stiffness of cracked reinforced concrete beam by neglecting the effect of interfacial microcracks.

Prediction Scheme of Torsional Strength of Reinforced Concrete Beam

2012 ◽  
Vol 214 ◽  
pp. 306-310
Author(s):  
Han Chen Huang
Keyword(s):  
Genetic Algorithm ◽  
Reinforced Concrete ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Ann Model ◽  
Torsional Strength ◽  
Prediction Scheme ◽  
Optimal Network

This study proposes a artificial neural network with genetic algorithm (GA-ANN) for predicting the torsional strength of reinforced concrete beam. Genetic algorithm is used to the optimal network structure and parameters. A database of the torsional failure of reinforced concrete beams with a rectangular section subjected to pure torsion was obtained from existing literature for analysis. This study compare the predictions of the GA-ANN model with the ACI 318 code used for analyzing the torsional strength of reinforced concrete beam. The results show that the proposed model provides reasonable predictions of the ultimate torsional strength of reinforced concrete beams and offers superior torsion accuracy compared to that of the ACI 318-89 equation.

In-Plane Force Effect of Reinforced Concrete Beam with Elastic Supports

2011 ◽  
Vol 287-290 ◽  
pp. 1896-1901
Author(s):  
Zhi Kun Guo ◽  
Wan Xiang Chen ◽  
Qi Fan Wang ◽  
Yu Huang ◽  
Chao Pu Li ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Nonlinear Characteristics ◽  
Elastic Supports ◽  
Calculation Results ◽  
Basic Equations ◽  
First Time ◽  
Good Agreement

The bearing capacities of one-way reinforced concrete beams with elastic supports are investigated in this paper. According to the nonlinear characteristics of the beams, the basic equations based on plastic theory of concrete are derived by considering the in-plane force effects that aroused by the constraints of supports when the beams deforming. It is indicated that the calculation results are in good agreement with experimental datum, and the influences of different supports on the bearing capacities of the beams are quantitatively given for the first time.

Uniform loading on the reinforced concrete beam produced by the specific cylinder-shaped rubber bags fully filled with air or water

2020 ◽  
Vol 23 (9) ◽  
pp. 1934-1947
Author(s):  
Dapeng Chen ◽  
Li Chen ◽  
Qin Fang ◽  
Yuzhou Zheng ◽  
Teng Pan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Element Model ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Uniform Loading ◽  
Air Bag

The bending behavior of reinforced concrete beams under uniform pressure is critical for the research of the blast-resistance performance of structural components under explosive loads. In this study, a bending test of five reinforced concrete beams with the dimensions of 200 mm (width) × 200 mm (depth) × 2500 mm (length) under uniform load produced by a specific cylinder-shaped rubber bag filled with air or water was conducted to investigate their flexural performances. An air bag load was applied to three of the reinforced concrete beams, a water bag load was applied to one reinforced concrete beam, and the remainder beam was subjected to the 4-point bending load. The experimental results highlighted that the air bag and water bag loading methods can be used to effectively apply uniform loads to reinforced concrete beams. Moreover, the stiffness of the air bag was improved by 123% in accordance with the initial pressure increases from 0.15 to 0.45 MPa. In addition, a finite element model of the test loading system was established using ABAQUS/Standard software. Moreover, the critical factors of the air bag loading method were analyzed using the numerical model. The calculated results were found to be in good agreement with the test data. The established finite element model can therefore be used to accurately simulate the action performances of the uniform loading technique using rubber bags filled with air or water.

scholarly journals Nonlinear creep in a steel-reinforced concrete beam

2020 ◽  
Vol 17 (5) ◽  
pp. 108-116
Author(s):  
S. O. Chepilko ◽  
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Reinforced Concrete Beam ◽  
Reinforced Concrete Beams ◽  
Nonlinear Creep ◽  
Short Term ◽  
Nonlinear Integral Equations ◽  
Steel Reinforced Concrete ◽  
Linear Creep ◽  
Resolving System

Problems of taking into account nonlinear creep in steel- reinforced concrete beams are considered basing on the integral equation of viscous-elastic-plasticity of concrete. There has been obtained the resolving system of nonlinear integral equations, a linearization of this system has been carried out, its asymptotic solutions have been written out for the theory of elastic heredity case. The analysis of taking into account nonlinear creep has been performed compared with the linear creep equations and an instantaneous (short-term) loading allowing for concrete’s nonlinear diagram.

scholarly journals The flexural behavior model of bamboo reinforced concrete beams using a hose clamp

2019 ◽  
Vol 276 ◽  
pp. 01033
Author(s):  
Muhtar ◽  
Sri Murni Dewi ◽  
Wisnumurti ◽  
As’ad Munawir
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beam ◽  
Load Capacity ◽  
Reinforced Concrete Beam ◽  
Load Test ◽  
Reinforced Concrete Beams ◽  
Flexural Behavior ◽  
Steel Reinforced Concrete ◽  
And Behavior ◽  
Hose Clamp

Bamboo can use at the simple concrete construction because of the tensile strength of its mechanical property. Meanwhile, a slippery surface of the bamboo caused cracks in the bamboo reinforced concrete beam (BRC) not to spread and yield slip failure between a bamboo bar and concrete. Load test at the BRC beam yield humble load capacity. This study aims to improve the capacity and behavior of BRC beam bending by giving waterproof coating, sand, and hose clamp installation. The beam test specimen with the size of 75x150x1100mm made as many as 26 pieces with the variety of reinforcement. The hose clamp used on the bamboo reinforcement varies with a distance of 0 cm, 15 cm, 20 cm, and 25 cm. The testing using a simple beam with two-point loading. The test results show that BRC beams have different bending behavior compared to the steel reinforced concrete beam (SRC).

Sign in / Sign up

Export Citation Format

Share Document