Lateral stress changes and shaft friction for model displacement piles in sand

2005 ◽  
Vol 42 (4) ◽  
pp. 1039-1052 ◽  
Author(s):  
Barry M Lehane ◽  
David J White

The paper describes a series of tests performed in a drum centrifuge on instrumented model displacement piles in normally consolidated sand. These tests examined the influence of the pile installation method, the stress level, and the pile aspect ratio on the increase in lateral effective stress on the pile shaft during static load testing to failure. A parallel series of constant normal load and constant normal stiffness (CNS) laboratory interface shear experiments was performed to assist interpretation of the centrifuge tests. It is shown that although the cycling associated with pile installation results in a progressive reduction in the stationary horizontal effective stress acting on a pile shaft and densification of the sand in a shear band close to the pile shaft, this sand dilates strongly during subsequent shearing to failure in a static load test. The dilation (the amount of which depends on the cyclic history) is constrained by the surrounding soil and therefore leads to large increases in lateral effective stresses and hence to large increases in mobilized shaft friction. The increase in lateral stress is shown to be related to the radial stiffness of the soil mass constraining dilation of the shear band and to be consistent with measurements made in appropriate CNS interface shear tests. The paper's findings assist in the extrapolation of model-scale pile test results to full-scale conditions.Key words: sand, displacement pile, centrifuge tests, shaft friction.

SPE Journal ◽  
2021 ◽  
pp. 1-21
Author(s):  
Saeed Rafieepour ◽  
Stefan Z. Miska ◽  
Evren M. Ozbayoglu ◽  
Nicholas E. Takach ◽  
Mengjiao Yu ◽  
...  

Summary In this paper, an extensive series of experiments was performed to investigate the evolution of poromechanical (dry, drained, undrained, and unjacketed moduli), transport (permeability), and strength properties during reservoir depletion and injection in a high-porosity sandstone (Castlegate). An overdetermined set of eight poroelastic moduli was measured as a function of confining pressure (Pc) and pore pressure (Pp). The results showed larger effect on pore pressure at low Terzaghi’s effective stress (nonlinear trend) during depletion and injection. Moreover, the rock sample is stiffer during injection than depletion. At the same Pc and Pp, Biot’s coefficient and Skempton’s coefficient are larger in depletion than injection. Under deviatoric loading, absolute permeability decreased by 35% with increasing effective confining stress up to 20.68 MPa. Given these variations in rock properties, modeling of in-situ-stress changes using constant properties could attain erroneous predictions. Moreover, constant deviatoric stress-depletion/injection failure tests showed no changes or infinitesimal variations of strength properties with depletion and injection. It was found that failure of Castlegate sandstone is controlled by simple effective stress, as postulated by Terzaghi. Effective-stress coefficients at failure (effective-stress coefficient for strength) were found to be close to unity (actual numbers, however, were 1.03 for Samples CS-5 and CS-9 and 1.04 for Sample CS-10). Microstructural analysis of Castlegate sandstone using both scanning electron microscope (SEM) and optical microscope revealed that the changes in poroelastic and transport properties as well as the significant hysteresis between depletion and injection are attributed to the existence and distribution of compliant components such as pores, microcracks, and clay minerals.


2020 ◽  
Vol 10 (16) ◽  
pp. 5492
Author(s):  
Michał Baca ◽  
Włodzimierz Brząkała ◽  
Jarosław Rybak

This work examined a new method of bi-directional static load testing for piles, referencing the Osterberg test. Measurements were taken, on a laboratory scale, using six models of piles driven into a box filled with sand. This method allowed for separate measurements of pile base and pile shaft bearing capacities. Based on the results, the total pile bearing capacity and equivalent Q–s diagrams were estimated. The results obtained show that the structure of the equivalent curve according to Osterberg is a good approximation of the standard Q–s curve obtained from load tests, except for loads close to the limit of bearing capacity (those estimates are also complicated by the inapplicability and ambiguity of a definition of the notion of limit bearing capacity); the equivalent pile capacity in the Osterberg method represents, on average, about 80% of the capacity from standard tests.


2020 ◽  
Vol 57 (3) ◽  
pp. 433-447 ◽  
Author(s):  
Shi-Jin Feng ◽  
Jie-Ni Chen ◽  
Hong-Xin Chen ◽  
Xin Liu ◽  
T. Zhao ◽  
...  

The interaction between soil and geotextile is essential for the performance of reinforced soil. This study reveals the microscopic mechanism of interface shear between sand and geotextile based on the discrete element method (DEM). The surface characteristics of geotextile are simulated by overlapped particles. The micromechanical parameters of sand, geotextile, and interface are calibrated effectively using laboratory test results. Three types of shear tests on the sand–geotextile interface are simulated; namely, interface direct shear test (IDST), double-sided interface shear test (D_IST), and interface direct shear test with periodic boundary (PBST). For IDST, the results show that the thickness of shear band is 2.4∼3.0 times the average particle diameter (D50); the contact force, percentage of sliding contact, and contact normal anisotropy inside the shear band are larger than those outside the shear band, whereas the coordination number is smaller inside the shear band. The mechanical response of D_IST is similar to that of IDST. However, D_IST has a shear band thickness of 3.0D50, and greater coordination number, percentage of sliding contact, and contact normal anisotropy. The results of PBST indicate that the peak stress and the shear band no longer appear without boundary constraint and the contact distribution is uniform.


2015 ◽  
Vol 2 ◽  
pp. 1
Author(s):  
Zhaohong Ji

<p>The stress route analytical method compensates for the limitation of traditional soil slope stability analytical method. Since it disregards the impact of effective stress route on the stress status and anti-shear strength of soil slope, it maps out the soil stress route drawing in the excavation process, and marks the anti-shear strength and shear stress changes under various conditions of soil. It causes the changes of the safety coefficient rules in the excavation of soil slope and affects the excavation stability of soil cutting and side slope. The result reveals: (1) The main analytical method of side slope stability which covers both the limit balance method and finite unit method fails to consider the impact of effective stress route on the existing stress status and anti-shear strength of soil slope; the stress route analytical method is able to overcome this limitation to a certain degree. (2) The stress route theory is adopted for analysis, in which, it can projected the whole stress of typical and most dangerous area of the slope, able to analyse the anti-shear strength of soil in a real-time manner, manage to express the safety coefficient changes in the stress route drawing and provides a selection of a suitable excavation plan by contrast. (3) In the overall excavation, the slope toe suffers from obvious stress concentration which expands to the surrounding areas and inconvenient for the side slope stability in the excavation.</p>


Energies ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2996 ◽  
Author(s):  
Gang Wang ◽  
Ke Wang ◽  
Yujing Jiang ◽  
Shugang Wang

In this study, we have built a dual porosity/permeability model through accurately expressing the volumetric strain of matrix and fracture from a three-dimensional method which aims to reveal the reservoir permeability evolution during the process of CO2-enhanced coalbed methane (CO2-ECBM) recovery. This model has accommodated the key competing processes of mechanical deformation and adsorption/desorption induced swelling/shrinkage, and it also considered the effect of fracture aperture and effective stress difference between each medium (fracture and matrix). We then numerically solve the permeability model using a group of multi-field coupling equations with the finite element method (FEM) to understand how permeability evolves temporally and spatially. We further conduct multifaceted analyses to reveal that permeability evolution near the wells is the most dramatic. This study shows that the farther away from the well, the gentler the evolution of permeability. The evolution of reservoir permeability near the injection well (IW) and the production well (PW) are very different, due to the combined effects of effective stress changes and gas adsorption and desorption. Furthermore, adsorption is the main controlling factor for the change of permeability for regions near the IW, while the change in effective stress is the main cause for the change in permeability near the PW. Increasing the injection pressure of CO2 will cause the reservoir permeability to evolve more quickly and dynamically.


Fuel ◽  
2011 ◽  
Vol 90 (3) ◽  
pp. 1292-1300 ◽  
Author(s):  
D. Jasinge ◽  
P.G. Ranjith ◽  
S.K. Choi

Sign in / Sign up

Export Citation Format

Share Document