ALL-DIELECTRIC PERIODIC MEDIA ENGINEERED FOR SLOW LIGHT STUDIES

2013 ◽  
Vol 27 (27) ◽  
pp. 1330020 ◽  
Author(s):  
H. KURT
Keyword(s):  
Group Velocity ◽  
Structural Changes ◽  
Slow Light ◽  
Spectral Characteristics ◽  
Group Index ◽  
Future Directions ◽  
Dispersion Engineering ◽  
Air Interface ◽  
Potential Applications ◽  
Light Waveguide

The paper presents various novel approaches to implementing slow light media by manipulating the group velocity via dispersion engineering of guided modes. Light is confined and then linked with a low group velocity inside a photonic crystal waveguide (PCW) and at the PC-air interface. We discuss both basic and engineered slow light waveguide structures. The structural changes in PCs greatly modify the spectral characteristics of the dispersion curves. The search for flat bands gives rise to various strategies for slowing the optical pulses. An appropriate and commonly adopted figure of merit (FOM) is accepted to quantify and characterize the performance of the designed slow light devices. The trade-off relationship between the group index and the bandwidth is highlighted. Efficient excitation of slow modes demands the design of additional interfaces as couplers between the input waveguide and slow mode guide structure. Other challenges of slow light studies, such as various loss sources, are mentioned. Finally, the potential applications of slow light are outlined, and remarks on future directions are presented.

Dispersionless one-way slow wave with large delay bandwidth product at the edge of gyromagnetic photonic crystal

2020 ◽  
Vol 34 (10) ◽  
pp. 2050086
Author(s):  
Ye Liu ◽  
Chun Jiang
Keyword(s):  
Photonic Crystal ◽  
Group Velocity ◽  
Communication Systems ◽  
Slow Light ◽  
Weak Interactions ◽  
Group Velocity Dispersion ◽  
Edge State ◽  
Group Index ◽  
Light Waveguide ◽  
Modal Field

We theoretically, demonstrate a high delay bandwidth product (DBP) and zero group velocity dispersion (GVD) in a two-dimensional one-way slow light waveguide. The waveguide consists of gyromagnetic photonic crystal (GMPC) and a cladding formed by silicon photonic crystal. At the edge of the band, weak interactions (“semi-anticrossing”) between the chiral edge state (CES) mode and the mode localized at the surface of cladding are observed. The group velocity of CES wave can be tuned by adjusting the modal field distribution. As a result, an extraordinarily large value of normalized DBP of 0.63 with a group index of 10.32 and a bandwidth ranging from [Formula: see text] to [Formula: see text] is obtained. This result may contribute to one-way slow light applications in information communication systems.

scholarly journals Slow Light Tuning in Annular Slotted Photonic Crystal Waveguide with Incoming Polymer

2021 ◽  
Vol 2109 (1) ◽  
pp. 012008
Author(s):  
Konttao Zhu ◽  
Hongxue Yang ◽  
Hui Du
Keyword(s):  
Photonic Crystal ◽  
Group Velocity ◽  
Slow Light ◽  
Transmission Rate ◽  
Group Velocity Dispersion ◽  
Flat Band ◽  
Group Index ◽  
Photonic Crystal Waveguide ◽  
Processing Scheme ◽  
Operating Wavelength

Abstract An advanced post-processing scheme of reconfigurable dielectric infiltration into an annular slotted photonic crystal waveguide (ASPhCW) is proposed in this paper. Ionic liquids have had prominent effects in enhancing the optical properties of photonic crystals, especially in the aspect of tuning the transmission rate and velocity through optical materials. Using the two-dimensional plane wave expansion method, the flat band dispersion of the slow light is obtained and the tuning of the operating wavelength of the crystal could be realized by incoming polymer technology. The operating wavelength tuning range could be as large as 459.27nm and the group index could be tuned as high as 44.8 with a near zero group velocity dispersion. Using this method, a high group index equaling 45 with the bandwidth equaling 11.3nm and the normalized delay bandwidth product (NDBP) equaling 0.25 is realized. This incoming polymer technology provides an effective method of getting flat band of slow light flexibly and makes it possible to offer longer delay and low group velocity after fabrication.

Terahertz polarization-independent electromagnetically-induced transparency structures

2020 ◽  
Vol 34 (16) ◽  
pp. 2050170
Author(s):  
Dandan Sun ◽  
Limei Qi
Keyword(s):  
Slow Light ◽  
Electromagnetically Induced Transparency ◽  
Metal Ring ◽  
Group Index ◽  
Light Effect ◽  
Terahertz Region ◽  
Coupling Behavior ◽  
Potential Applications ◽  
Induced Transparency ◽  
Polarization Independent

Two simple polarization-independent electromagnetically-induced transparency (EIT) metamaterials are numerically and experimentally demonstrated at the terahertz region. The first structure is composed of two metal concentric rings on a substrate, while the second one is composed of one metal ring with a cross in it. The bright–bright coupling behavior appears in the two symmetric polarization-independent EIT structures while it is generally observed in asymmetrically structures. In addition, the large group index is extracted to verify the slow-light effect of the two EIT structures. These simple EIT structures may have potential applications in certain areas, including sensing, slow-light and filtering devices.

Slow Light Waveguide with Low Group-Velocity Dispersion and Low Loss in 2-D Photonic Crystal

2011 ◽  
Vol 31 (1) ◽  
pp. 0113001
Author(s):  
张栋 Zhang DongZhao ◽  
赵建林 JianlinLü ◽  
吕淑媛 Shuyuan
Keyword(s):  
Photonic Crystal ◽  
Group Velocity ◽  
Slow Light ◽  
Velocity Dispersion ◽  
Group Velocity Dispersion ◽  
Low Loss ◽  
Light Waveguide

scholarly journals Group Velocity Modulation and Light Field Focusing of the Edge States in Chirped Valley Graphene Plasmonic Metamaterials

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1808
Author(s):  
Liqiang Zhuo ◽  
Huiru He ◽  
Ruimin Huang ◽  
Shaojian Su ◽  
Zhili Lin ◽  
...  
Keyword(s):  
Group Velocity ◽  
Light Field ◽  
Slow Light ◽  
Dielectric Materials ◽  
Degree Of Freedom ◽  
Geometrical Parameters ◽  
Edge States ◽  
Velocity Modulation ◽  
Plasmonic Metamaterials ◽  
On Chip

The valley degree of freedom, like the spin degree of freedom in spintronics, is regarded as a new information carrier, promoting the emerging valley photonics. Although there exist topologically protected valley edge states which are immune to optical backscattering caused by defects and sharp edges at the inverse valley Hall phase interfaces composed of ordinary optical dielectric materials, the dispersion and the frequency range of the edge states cannot be tuned once the geometrical parameters of the materials are determined. In this paper, we propose a chirped valley graphene plasmonic metamaterial waveguide composed of the valley graphene plasmonic metamaterials (VGPMs) with regularly varying chemical potentials while keeping the geometrical parameters constant. Due to the excellent tunability of graphene, the proposed waveguide supports group velocity modulation and zero group velocity of the edge states, where the light field of different frequencies focuses at different specific locations. The proposed structures may find significant applications in the fields of slow light, micro–nano-optics, topological plasmonics, and on-chip light manipulation.

scholarly journals Towards lab-on-chip ultrasensitive ethanol detection using photonic crystal waveguide operating in the mid infrared

Nanophotonics ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Ali Rostamian ◽  
Ehsan Madadi-Kandjani ◽  
Hamed Dalir ◽  
Volker J. Sorger ◽  
Ray T. Chen
Keyword(s):  
Photonic Crystal ◽  
Slow Light ◽  
High Sensitivity ◽  
Guided Wave ◽  
Silicon On Insulator ◽  
Group Index ◽  
Photonic Crystal Waveguide ◽  
Mid Infrared ◽  
Lab On Chip ◽  
On Chip

Abstract Thanks to the unique molecular fingerprints in the mid-infrared spectral region, absorption spectroscopy in this regime has attracted widespread attention in recent years. Contrary to commercially available infrared spectrometers, which are limited by being bulky and cost-intensive, laboratory-on-chip infrared spectrometers can offer sensor advancements including raw sensing performance in addition to use such as enhanced portability. Several platforms have been proposed in the past for on-chip ethanol detection. However, selective sensing with high sensitivity at room temperature has remained a challenge. Here, we experimentally demonstrate an on-chip ethyl alcohol sensor based on a holey photonic crystal waveguide on silicon on insulator-based photonics sensing platform offering an enhanced photoabsorption thus improving sensitivity. This is achieved by designing and engineering an optical slow-light mode with a high group-index of n g  = 73 and a strong localization of modal power in analyte, enabled by the photonic crystal waveguide structure. This approach includes a codesign paradigm that uniquely features an increased effective path length traversed by the guided wave through the to-be-sensed gas analyte. This PIC-based lab-on-chip sensor is exemplary, spectrally designed to operate at the center wavelength of 3.4 μm to match the peak absorbance for ethanol. However, the slow-light enhancement concept is universal offering to cover a wide design-window and spectral ranges towards sensing a plurality of gas species. Using the holey photonic crystal waveguide, we demonstrate the capability of achieving parts per billion levels of gas detection precision. High sensitivity combined with tailorable spectral range along with a compact form-factor enables a new class of portable photonic sensor platforms when combined with integrated with quantum cascade laser and detectors.

Effects of Metal Stress on Visible/Near-Infrared Reflectance Spectra of Vegetation

2011 ◽  
Vol 347-353 ◽  
pp. 2735-2738 ◽  
Author(s):  
Guang Yu Chi ◽  
Yi Shi ◽  
Xin Chen ◽  
Jian Ma ◽  
Tai Hui Zheng
Keyword(s):  
Heavy Metal ◽  
Structural Changes ◽  
Near Infrared ◽  
Leaf Surface ◽  
Spectral Response ◽  
Spectral Characteristics ◽  
Surface Characteristics ◽  
Heavy Metal Stress ◽  
Metal Stress ◽  
Near Infrared Reflectance

Vegetation which suffers from heavy metal stresses can cause changes of leaf color, shape and structural changes. The spectral characteristics of vegetation leaves is related to leaf thickness, leaf surface characteristics, the content of water, chlorophyll and other pigments. So the eco-physiology changes of plants can be reflected by spectral reflectance. Studies on the spectral response of vegetation to heavy metal stress can provide a theoretical basis for remote sensing monitoring of metal pollution in soils. In recent decades, there are substantial amounts of literature exploring the effects of heavy metals on vegetation spectra.

scholarly journals Selective time-dependent changes of Cu(DPPE)(DMP)·PF6on photoexcitation

2014 ◽  
Vol 70 (a1) ◽  
pp. C776-C776 ◽  
Author(s):  
Elzbieta Trzop ◽  
Bertrand Fournier ◽  
Katarzyna Jarzembska ◽  
Jesse Sokolow ◽  
Radoslaw Kaminski ◽  
...  
Keyword(s):  
Structural Changes ◽  
Dye Sensitized Solar Cells ◽  
Department Of Energy ◽  
Data Sets ◽  
Monoclinic System ◽  
Time Resolved ◽  
Pump Probe ◽  
Light Emitting Devices ◽  
Potential Applications ◽  
Photon Source

Thanks to their potential applications as light-emitting devices, chemical sensors and dye-sensitized solar cells, heteroleptic copper (I) complexes have been extensively studied. Cu(DPPE)(DMP)·PF6(dppe= 1,2-bis(diphenylphosphino)ethane; dmp = 2,9-dimethyl-1,10-phenanthroline) crystallizes in the monoclinic system, P21/c, with two independent molecules in the asymmetric unit. Previous studies on this system [1,2] show strong temperature-dependent emission. The complex was studied at 90K under 355nm laser excitation. At this temperature, the luminescence decay for Cu(DPPE)(DMP)·PF6is biexponential with lifetimes of ~3μs and ~28μs. Two time-resolved X-ray diffraction techniques were applied for studies: (1) a Laue technique at BioCARS ID-14 beamline at the Advanced Photon Source, and (2) monochromatic diffraction at a newly constructed in-house pump-probe monochromatic facility at the University at Buffalo. Structural changes determined with the two methods are in qualitative agreement; discrepancies in position of the Cu and P atoms were observed. The molecular distortions were smaller than those determined at 16K in the earlier synchrotron study by Vorontsov et al. [2]. Photodeformation maps (see Figure below), in which the increase in temperature on photoexcitation has been eliminated, clearly illustrate the photoinduced atomic shifts for both data sets. Results will be compared with those obtained for other studied heteroleptic copper (I) complexes, for instance Cu[(1,10-phenanthroline-N,N′) bis(triphenylphosphine)]·BF4[3]. The in-house pump-probe facility is discussed by Radoslaw Kaminski at this meeting. Research funded by the National Science Foundation (CHE1213223). BioCARS Sector 14 at APS is supported by NIH (RR007707). The Advanced Photon Source is funded by the Office of Basic Energy Sciences, U.S. Department of Energy, (W-31-109-ENG-38). KNJ is supported by the Polish Ministry of Science and Higher Education through the "Mobility Plus" program.

scholarly journals Slow light bimodal interferometry in one-dimensional photonic crystal waveguides

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Luis Torrijos-Morán ◽  
Amadeu Griol ◽  
Jaime García-Rupérez
Keyword(s):  
Photonic Crystal ◽  
Group Velocity ◽  
Communication Networks ◽  
Slow Light ◽  
Single Channel ◽  
Point Of Care ◽  
Semiconductor Industry ◽  
Optical Modulator ◽  
One Dimensional ◽  
Dimensional Photonic Crystal

AbstractStrongly influenced by the advances in the semiconductor industry, the miniaturization and integration of optical circuits into smaller devices has stimulated considerable research efforts in recent decades. Among other structures, integrated interferometers play a prominent role in the development of photonic devices for on-chip applications ranging from optical communication networks to point-of-care analysis instruments. However, it has been a long-standing challenge to design extremely short interferometer schemes, as long interaction lengths are typically required for a complete modulation transition. Several approaches, including novel materials or sophisticated configurations, have been proposed to overcome some of these size limitations but at the expense of increasing fabrication complexity and cost. Here, we demonstrate for the first time slow light bimodal interferometric behaviour in an integrated single-channel one-dimensional photonic crystal. The proposed structure supports two electromagnetic modes of the same polarization that exhibit a large group velocity difference. Specifically, an over 20-fold reduction in the higher-order-mode group velocity is experimentally shown on a straightforward all-dielectric bimodal structure, leading to a remarkable optical path reduction compared to other conventional interferometers. Moreover, we experimentally demonstrate the significant performance improvement provided by the proposed bimodal photonic crystal interferometer in the creation of an ultra-compact optical modulator and a highly sensitive photonic sensor.

Sign in / Sign up

Export Citation Format

Share Document