A NEW ELECTRONICALLY-TUNABLE ACTIVE-ONLY UNIVERSAL BIQUAD

2011 ◽  
Vol 20 (03) ◽  
pp. 549-555 ◽  
Author(s):  
A. K. SINGH ◽  
R. SENANI ◽  
D. R. BHASKAR ◽  
R. K. SHARMA
Keyword(s):  
Pass Band ◽  
Voltage Mode ◽  
Op Amp ◽  
Op Amps ◽  
Reasonable Number ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable ◽  
High Pass ◽  
Realization Condition

A number of configurations for realizing voltage-mode (VM) biquads using op-amps and OTAs have been presented in the literature, however, none of these provide the following desirable properties simultaneously: (i) realizability of all the five standard filters (namely; low pass, high pass, band pass, band stop and all pass), (ii) tunability of all the three filter parameters (namely; ω0, bandwidth or Q0 and gain) and (iii) not requiring any realization condition in any of the five filter responses. This paper presents a new configuration which does possess all the above mentioned desirable properties simultaneously while using only two internally-compensated type op-amps and a reasonable number of OTAs. The workability of the new configuration has been demonstrated by SPICE simulations based upon CMOS Op-amp and CMOS OTAs.

NOVEL VOLTAGE-MODE UNIVERSAL FILTER USING ONLY TWO CDBAs

2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN
Keyword(s):  
Pass Band ◽  
Universal Filter ◽  
Input Selection ◽  
Voltage Mode ◽  
Single Output ◽  
Control Computer ◽  
Low Pass ◽  
Band Pass ◽  
Pass Through ◽  
High Pass

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.

Second-Order Voltage-Mode Universal Filters Using Two DVCCs, Two Grounded Capacitors and Four Resistors

2016 ◽  
Vol 25 (12) ◽  
pp. 1650154 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Integrated Circuit ◽  
Matching Condition ◽  
Second Order ◽  
Point Of View ◽  
Pass Band ◽  
Current Conveyors ◽  
Voltage Mode ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

In this paper, two new second-order voltage-mode universal filters are proposed. Both of the proposed filters use only two differential voltage current conveyors (DVCCs), four resistors and two grounded capacitors which are advantageous from integrated circuit technology point of view. They can simultaneously provide second-order low-pass, high-pass, band-pass, notch and all-pass responses. They offer orthogonal control of angular resonance frequency and quality factor. However, they have a single matching condition for only all-pass responses. A number of simulations based on SPICE program are accomplished in order to demonstrate the performance of both filters.

REALIZATION OF A GENERAL RESISTORLESS ACTIVE BIQUAD USING CBTA

2012 ◽  
Vol 21 (01) ◽  
pp. 1250013 ◽  
Author(s):  
MEHMET SAGBAS ◽  
MUHAMMET KOKSAL
Keyword(s):  
Integrated Circuit ◽  
Pass Band ◽  
Active Components ◽  
Order Filter ◽  
Low Pass ◽  
Band Pass ◽  
Transconductance Amplifiers ◽  
Electronically Tunable ◽  
High Pass ◽  
Circuit Technology

In this paper, a general electronically tunable resistorless biquad, which realizes current ratio transfer function using current backward transconductance amplifiers is proposed. The biquad contains only two active components and two grounded capacitors, which make it convenient for production by the integrated circuit technology. The proposed biquad realizes all of the basic second order filter characteristics: low pass, high pass, band pass, band reject, and finally all pass. It is convenient for cascading with other similar biquads as well as with any two-port circuit with low impedance input to achieve higher order filter characteristics. The simulations that are performed using PSPICE simulator exhibit satisfactory results coherent with the theory.

Realization of Resistorless and Electronically Tunable Inverse Filters Using VDTA

2019 ◽  
Vol 28 (09) ◽  
pp. 1950143 ◽  
Author(s):  
Praveen Kumar ◽  
Neeta Pandey ◽  
Sajal K. Paul
Keyword(s):  
Cmos Technology ◽  
Angular Frequency ◽  
Pass Band ◽  
Passive Component ◽  
Inverse Filter ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable ◽  
High Pass

This paper presents resistorless realization of inverse filters using voltage differencing transconductance amplifier (VDTA). First, four topologies are proposed which provide inverse low-pass, high-pass, band-pass, and band-reject responses. Subsequently, a unified inverse filter is also derived by incorporating two switches in the combination of proposed inverse low-pass and inverse band-pass topologies. This topology is capable of providing inverse low-pass, inverse high-pass, inverse band-pass, and inverse band-reject responses by appropriate switch settings. The proposed inverse filter structures are electronically tunable and use only grounded capacitors. The behavior of the proposed filters is also investigated for nonidealities. To verify the functionality of the proposed inverse filter circuits, SPICE simulation is carried out using 0.18-[Formula: see text]m CMOS technology parameters from TSMC. The effect of deviation in the active and passive component values on angular frequency is tested through Monte Carlo simulation.

scholarly journals Single-input Multiple-output Signals Third-order Active-R Filter for different Circuit Merit Factor (Q)

2015 ◽  
Vol 12 (3) ◽  
pp. 611-618
Author(s):  
Baghdad Science Journal
Keyword(s):  
Stop Band ◽  
Pass Band ◽  
Third Order ◽  
Op Amp ◽  
Merit Factor ◽  
Input Multiple Output ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
High Pass

Single-input Multiple-output Signals Third-order Active-R Filter for different Circuit Merit Factor Q Configuration is proposed. This paper discusses a new configuration to realize third-order low pass, band pass and high pass. The presented circuit uses Single-input Multiple-output signals, OP-AMP and passive components. This filter is useful for high frequency operation, monolithic IC implementation and it is easy to design .This circuit gives three filter functions low-pass, high-pass and band-pass. This filter circuit can be used for different merit factor (Q) with high pass band gain. This gives better stop-band attenuation and sharper cut-off at the edge of the pass-band. Thus the response shows wider pass-band. The Ideal value of this filter circuit which is closed to Ideal value of third-order active-R filter is at 0.8? Q ?6. The advantages of this circuit are reduction in size and weight, increased circuit reliability, more economical and easy for manufacturing.

CURRENT-MODE ACTIVE-C FILTER EMPLOYING REDUCED NUMBER OF CCCII+s

2007 ◽  
Vol 16 (04) ◽  
pp. 507-516 ◽  
Author(s):  
SHAHRAM MINAEI ◽  
ERKAN YUCE
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Passive Component ◽  
Resistorless Filter ◽  
Low Pass ◽  
Component Matching ◽  
Band Pass ◽  
High Output Impedance ◽  
Quality Factor Q ◽  
High Pass

In this paper, a universal current-mode second-order active-C filter for simultaneously realizing low-pass, band-pass and high-pass responses is proposed. The presented filter employs only three plus-type second-generation current-controlled conveyors (CCCII+s). This filter needs no critical active and passive component matching conditions and no additional active and passive elements for realizing high output impedance low-pass, band-pass and high-pass characteristics. The angular resonance frequency (ω0) and quality factor (Q) of the proposed resistorless filter can be tuned electronically. To verify the theoretical analysis and to exhibit the performance of the proposed filter, it is simulated with SPICE program.

scholarly journals Design and Implementation of Digital Filters for ECG Data Based on Field Programmable Gate Array and MATLAB

2020 ◽  
pp. 17-19
Author(s):  
Emre Cancioglu ◽  
Gokberk Cakiroglu ◽  
Alkim Gokcen ◽  
Yilmaz Sefa Altanay
Keyword(s):  
Digital Filters ◽  
Pass Band ◽  
System Generator ◽  
Design And Implementation ◽  
Field Programmable ◽  
Low Pass ◽  
Band Pass ◽  
Database Platform ◽  
High Pass ◽  
Ecg Data

This study provides design and implementation of four digital filters (low pass, high pass, band pass and band stop) for ECG (electrocardiogram) data on FPGA with MATLAB by a serial communication. The study is conducted with using ECG data which is obtained from PhysioBank Database platform. SysGen (System Generator for DSP) which is a toolbox for MATLAB is used for designing and implementing the digital filters. The aim of the study is to perform four different digital filters with various blocks on the SysGen Toolbox. The study then examines the results of four different digital filters.

A New Tunable SISO Filter Designed in 40nm CMOS for Bilateral Inverse and Buffer Filtering Applications

2021 ◽  
pp. 2150240
Author(s):  
Umar Mohammad ◽  
Fang Tang ◽  
Shu Zhou ◽  
Mohd Yusuf Yasin
Keyword(s):  
Simulation Analysis ◽  
Pass Band ◽  
Single Input Single Output ◽  
Change Of Direction ◽  
Single Output ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
Parasitic Components ◽  
High Pass

A new study imitating the design and implementation of single-input–single-output (SISO) filters as bilateral filters has been presented in this paper. Second generation current controlled current conveyor (CCCII), being a popular low power active element was considered for the realization of the proposed design. Complete design, analysis and implementation of the voltage mode SISO filter was done using only two CCCII’s and two passive parasitic components. The striking feature of this work is that the proposed design can be made to work at either the input node or the output node, as well as in the cases; the change of direction changes the filter into an inverse filter and buffer filter. Basic filter applications like low-pass, high-pass, band-pass and band-stop were aimed to check the uniformity of the proposed design at different frequencies. Results perceived from the simulation study were fare enough on both the side nodes of the proposed design. Categorically, the circuit can be aimed to work in lieu of a filter transceiver. The consistency of the circuit was analyzed by the nodal analysis. Whereas the working performance was enormously analyzed and evaluated during the simulation analysis. The proposed design was simulated in HSPICE tool to exhibit and exploit the delivery, using the 45[Formula: see text]nm predictive technology model (PTM) parameters, with [Formula: see text][Formula: see text]V rail to rail voltages. Maximum power consumption of the circuit is around 138.5[Formula: see text][Formula: see text]W. Finally, the design was also implemented in Cadence Virtuoso using 40[Formula: see text]nm SMIC parameters.

Sign in / Sign up

Export Citation Format

Share Document