Second-Order Voltage-Mode Universal Filters Using Two DVCCs, Two Grounded Capacitors and Four Resistors

2016 ◽  
Vol 25 (12) ◽  
pp. 1650154 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Integrated Circuit ◽  
Matching Condition ◽  
Second Order ◽  
Point Of View ◽  
Pass Band ◽  
Current Conveyors ◽  
Voltage Mode ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

In this paper, two new second-order voltage-mode universal filters are proposed. Both of the proposed filters use only two differential voltage current conveyors (DVCCs), four resistors and two grounded capacitors which are advantageous from integrated circuit technology point of view. They can simultaneously provide second-order low-pass, high-pass, band-pass, notch and all-pass responses. They offer orthogonal control of angular resonance frequency and quality factor. However, they have a single matching condition for only all-pass responses. A number of simulations based on SPICE program are accomplished in order to demonstrate the performance of both filters.

NOVEL VOLTAGE-MODE UNIVERSAL FILTER USING ONLY TWO CDBAs

2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN
Keyword(s):  
Pass Band ◽  
Universal Filter ◽  
Input Selection ◽  
Voltage Mode ◽  
Single Output ◽  
Control Computer ◽  
Low Pass ◽  
Band Pass ◽  
Pass Through ◽  
High Pass

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.

A NEW ELECTRONICALLY-TUNABLE ACTIVE-ONLY UNIVERSAL BIQUAD

2011 ◽  
Vol 20 (03) ◽  
pp. 549-555 ◽  
Author(s):  
A. K. SINGH ◽  
R. SENANI ◽  
D. R. BHASKAR ◽  
R. K. SHARMA
Keyword(s):  
Pass Band ◽  
Voltage Mode ◽  
Op Amp ◽  
Op Amps ◽  
Reasonable Number ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable ◽  
High Pass ◽  
Realization Condition

A number of configurations for realizing voltage-mode (VM) biquads using op-amps and OTAs have been presented in the literature, however, none of these provide the following desirable properties simultaneously: (i) realizability of all the five standard filters (namely; low pass, high pass, band pass, band stop and all pass), (ii) tunability of all the three filter parameters (namely; ω0, bandwidth or Q0 and gain) and (iii) not requiring any realization condition in any of the five filter responses. This paper presents a new configuration which does possess all the above mentioned desirable properties simultaneously while using only two internally-compensated type op-amps and a reasonable number of OTAs. The workability of the new configuration has been demonstrated by SPICE simulations based upon CMOS Op-amp and CMOS OTAs.

A New CCII Based Voltage-Mode Multifunctional Filter with Reduced Number of Active and Passive Elements

2015 ◽  
Vol 24 (04) ◽  
pp. 1550047 ◽  
Author(s):  
Firat Yucel ◽  
Erkan Yuce
Keyword(s):  
Time Domain ◽  
Input Impedance ◽  
Current Conveyors ◽  
High Input ◽  
High Input Impedance ◽  
Voltage Mode ◽  
Low Pass ◽  
Band Pass ◽  
Simulation Results ◽  
High Pass

In this paper, a new voltage-mode (VM) multifunctional filter comprising two second-generation current conveyors (CCIIs) is proposed. The proposed filter with one input and three outputs is also composed of three resistors and two grounded capacitors. The proposed filter has high input impedance; thus, it can be easily connected with other VM circuits. The proposed filter can simultaneously provide low-pass (LP), band-pass (BP) and high-pass (HP) responses. A number of time domain and frequency domain simulation results are included to confirm the claimed theory.

scholarly journals Voltage Mode Universal Biquad Using CCCII

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
Ashish Ranjan ◽  
Sajal K. Paul
Keyword(s):  
Pass Band ◽  
Current Conveyors ◽  
Ic Design ◽  
Passive Components ◽  
Voltage Mode ◽  
Single Output ◽  
Low Pass ◽  
Minimum Number ◽  
Band Pass ◽  
Low Sensitivity

This paper proposes a multi-input single-output (MISO) second-order active-C voltage mode (VM) universal filter using two second-generation current-controlled current conveyors (CCCIIs) and two equal-valued capacitors. The proposed circuit realizes low pass, band pass, high pass, all pass, and notch responses from the same topology. The filter uses-minimum number of passive components and no resistor which is suitable for IC Design. The filter enjoys low-sensitivity performance and exhibits electronic and orthogonal tunability of pole frequency () and quality factor () via bias current of CCCIIs. PSPICE simulation results confirm the theory.

CDTAs Based Current-Mode Universal Biquad Filters with Orthogonal Control of Quality Factor and Pole Frequency

2013 ◽  
Vol 787 ◽  
pp. 501-507
Author(s):  
Saksit Summart ◽  
Chanchai Thongsopa
Keyword(s):  
Quality Factor ◽  
Integrated Circuit ◽  
Current Mode ◽  
Pass Band ◽  
Cascade Connection ◽  
Low Pass ◽  
Band Pass ◽  
High Output Impedance ◽  
Further Development ◽  
High Pass

This article presents current-mode universal biquad filters based on CDTAs. The filter circuits using four CDTAs and two grounded capacitors which are able to provide low-pass, high-pass, band-pass, band-reject and all-pass functions. The pole frequency can be orthogonally controlled from quality factor and the circuits have high output impedance appropriate for cascade connection application in current mode which is capable to directly drive load. This qualification is very appropriate for further development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.

REALIZATION OF A GENERAL RESISTORLESS ACTIVE BIQUAD USING CBTA

2012 ◽  
Vol 21 (01) ◽  
pp. 1250013 ◽  
Author(s):  
MEHMET SAGBAS ◽  
MUHAMMET KOKSAL
Keyword(s):  
Integrated Circuit ◽  
Pass Band ◽  
Active Components ◽  
Order Filter ◽  
Low Pass ◽  
Band Pass ◽  
Transconductance Amplifiers ◽  
Electronically Tunable ◽  
High Pass ◽  
Circuit Technology

In this paper, a general electronically tunable resistorless biquad, which realizes current ratio transfer function using current backward transconductance amplifiers is proposed. The biquad contains only two active components and two grounded capacitors, which make it convenient for production by the integrated circuit technology. The proposed biquad realizes all of the basic second order filter characteristics: low pass, high pass, band pass, band reject, and finally all pass. It is convenient for cascading with other similar biquads as well as with any two-port circuit with low impedance input to achieve higher order filter characteristics. The simulations that are performed using PSPICE simulator exhibit satisfactory results coherent with the theory.

scholarly journals One-Input Three-Output Current-Mode Universal Filter Using Translinear Current Conveyors

2019 ◽  
Vol 2 (4) ◽  
pp. 101
Author(s):  
Montree Kumngern
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Current Conveyors ◽  
Current Response ◽  
Universal Filter ◽  
Low Pass ◽  
Band Pass ◽  
Active Matching ◽  
High Output Impedance ◽  
High Pass

This paper presents a new current-mode universal filter with one-input three-output employing three translinear current conveyors and two grounded capacitors. The proposed filter provides low-pass, band-pass, high-pass current response with high output impedance output which can be directly connected for current-mode circuit. The band-pass and all-pass filters can also be obtained. The parameters wo and Q can be controlled separately and electronically by the bias currents of current conveyors. For realizing all filtering functions, no passive and active matching conditions are required. The active and passive sensitivities are low. The characteristic of the proposed circuit can be confirmed by SPICE simulations.

scholarly journals DDCCTA-Based Universal filter and Quadrature Oscillator

2018 ◽  
Vol 3 (2) ◽  
pp. 18-21
Author(s):  
Rashmika Rai ◽  
◽  
S Indu
Keyword(s):  
Integrated Circuit ◽  
Notch Filter ◽  
Pass Band ◽  
Universal Filter ◽  
Passive Components ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
High Pass

The study presents a universal filter and Oscillator obtain by applying only single input. All the passive components used are grounded which is suitable for integrated circuit implementation. In the circuit by applying for single input simultaneously low pass, High Pass, Band Pass, All Pass, and Notch filter is obtained by using two blocks of Differential Difference current conveyor transconductance amplifier.

A New DVCC+ Based Second-Order Current-Mode Universal Filter Consisting of Only Grounded Capacitors

2017 ◽  
Vol 26 (09) ◽  
pp. 1750130 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Notch Filter ◽  
Current Mode ◽  
Second Order ◽  
Pass Band ◽  
Current Conveyors ◽  
Universal Filter ◽  
Pass Filter ◽  
Low Pass ◽  
Band Pass ◽  
High Output Impedance

In this paper, a new second-order current-mode universal filter using only two plus-type differential voltage current conveyors, three resistors and two grounded capacitors is proposed. The proposed circuit with two identical inputs and three outputs can simultaneously provide second-order high output impedance low-pass, band-pass and notch filter responses. Also, it can realize high-pass and all-pass filter responses with interconnection of relevant output currents. It can be easily tuned electronically. It can be operated properly at high frequencies. A number of simulations based on SPICE program and an experimental test are achieved in order to demonstrate the performance of the proposed filter.

Sign in / Sign up

Export Citation Format

Share Document