scholarly journals CONTINUOUS MICROSTRUCTURAL CORRELATION OF SLAG/SUPERPLASTICIZER CEMENT PASTES BY HEAT AND IMPEDANCE METHODS VIA FRACTAL ANALYSIS

Fractals ◽  
2017 ◽  
Vol 25 (04) ◽  
pp. 1740003 ◽  
Author(s):  
S. W. TANG ◽  
R. J. CAI ◽  
Z. HE ◽  
X. H. CAI ◽  
H. Y. SHAO ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fractal Analysis ◽  
Setting Time ◽  
Blended Cement ◽  
Impedance Measurement ◽  
Heat Evolution ◽  
Early Age ◽  
Contact Impedance ◽  
Cement Pastes ◽  
Early Age Hydration

This paper presents a preliminary work to evaluate the influence of slag and superplasticizer on the early-age hydration of cement pastes by an innovative non-contact impedance measurement, heat evolution method, compressive strength and setting time tests. Besides, the cumulative pore volume obtained from modulus and phase of impedance in different hydration sections is taken to continuously correlate the cumulative heat releasing of cement pastes via the fractal analysis. Retarded phenomena and mechanism of hydration in cement pastes incorporated with slag and superplasticizer are studied, respectively. It is found that the compressive strength and setting time have a good linear relation with the slag amount in blended cement pastes.

Behavior of Cement Pastes and Mortar Containing Phosphogypsum

2015 ◽  
Vol 668 ◽  
pp. 181-188 ◽  
Author(s):  
Hanan El Nouhy ◽  
Enas Khattab ◽  
Sayieda Zeedan
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Blended Cement ◽  
X Ray Diffraction ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Second Stage ◽  
Setting Times ◽  
Initial Setting ◽  
Two Stages

The aim of this study is to investigate the effects of phosphogypsum on the properties of both cement pastes and mortars. Normal Portland cement CEM Ι 32,5N, Limestone Blended cement CEM ΙΙ B-L32,5N, and Slag cement CEM ΙΙ A-S32,5N were used. These cements were partially substituted by 0,2,4,6,8,10,and 15% of phosphogypsum. The test program was divided to two stages. In the first stage, tests were conducted according to BSEN 196, namely setting times (initial and final), soundness, and compressive strength (at ages 7 and 28 days). In the second stage, X-ray diffraction (XRD), and scanning electron microscope (SEM) were conducted on selected mixes from first stage. The results show that the three types of cements with the various replacement percentages of phosphogypsum met the limit of initial setting time, as well as, provided soundness of 2 mm. Also, in terms of compressive strength, it was proven, that it is possible to partially replace the three tested types of cements by phosphogypsum by up to 8%and 15% with regard to cement/sand ratio of (1:3) and (1:2) respectively.

scholarly journals Effect of Calcium Nitrate on the Properties of Portland–Limestone Cement-Based Concrete Cured at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1611
Author(s):  
Gintautas Skripkiūnas ◽  
Asta Kičaitė ◽  
Harald Justnes ◽  
Ina Pundienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Calcium Nitrate ◽  
Curing Temperature ◽  
Hardened Concrete ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Early Strength

The effect of calcium nitrate (CN) dosages from 0 to 3% (of cement mass) on the properties of fresh cement paste rheology and hardening processes and on the strength of hardened concrete with two types of limestone-blended composite cements (CEM II A-LL 42.5 R and 42.5 N) at different initial (two-day) curing temperatures (−10 °C to +20 °C) is presented. The rheology results showed that a CN dosage up to 1.5% works as a plasticizing admixture, while higher amounts demonstrate the effect of increasing viscosity. At higher CN content, the viscosity growth in normal early strength (N type) cement pastes is much slower than in high early strength (R type) cement pastes. For both cement-type pastes, shortening the initial and final setting times is more effective when using 3% at +5 °C and 0 °C. At these temperatures, the use of 3% CN reduces the initial setting time for high early strength paste by 7.4 and 5.4 times and for normal early strength cement paste by 3.5 and 3.4 times when compared to a CN-free cement paste. The most efficient use of CN is achieved at −5 °C for compressive strength enlargement; a 1% CN dosage ensures the compressive strength of samples at a −5 °C initial curing temperature, with high early strength cement exceeding 3.5 MPa but being less than the required 3.5 MPa in samples with normal early strength cement.

scholarly journals Utilization of Solid Waste from Brick Industry and Hydrated Lime in Self-Compacting Cement Pastes

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1109
Author(s):  
Mati Ullah Shah ◽  
Muhammad Usman ◽  
Muhammad Usman Hanif ◽  
Iqra Naseem ◽  
Sara Farooq
Keyword(s):  
Mechanical Properties ◽  
Solid Waste ◽  
Manufacturing Industry ◽  
Setting Time ◽  
Hydrated Lime ◽  
Pozzolanic Reaction ◽  
Early Age ◽  
Cement Pastes ◽  
Brick Powder ◽  
High Degree

The huge amount of solid waste from the brick manufacturing industry can be used as a cement replacement. However, replacement exceeding 10% causes a reduction in strength due to the slowing of the pozzolanic reaction. Therefore, in this study, the pozzolanic potential of brick waste is enhanced using ultrafine brick powder with hydrated lime (HL). A total of six self-compacting paste mixes were studied. HL 2.5% by weight of binder was added in two formulations: 10% and 20% of waste burnt brick powder (WBBP), to activate the pozzolanic reaction. An increase in the water demand and setting time was observed by increasing the replacement percentage of WBBP. It was found that the mechanical properties of mixes containing 5% and 10% WBBP performed better than the control mix, while the mechanical properties of the mixes containing 20% WBBP were found to be almost equal to the control mix at 90 days. The addition of HL enhanced the early-age strength. Furthermore, WBBP formulations endorsed improvements in both durability and rheological properties, complemented by reduced early-age shrinkage. Overall, it was found that brick waste in ultrafine size has a very high degree of pozzolanic potential and can be effectively utilized as a supplementary cementitious material.

scholarly journals Analysis of the Influence of Crystalline Admixtures at Early Age Performance of Cement-Based Mortar by Electrical Resistance Monitoring

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5705
Author(s):  
Rubén Beltrán Cobos ◽  
Fabiano Tavares Pinto ◽  
Mercedes Sánchez Moreno
Keyword(s):  
Compressive Strength ◽  
Thermogravimetric Analysis ◽  
Remote Monitoring ◽  
Electrical Resistance ◽  
Setting Time ◽  
Early Age ◽  
Resistance Monitoring ◽  
Initial Setting Time ◽  
Characterization Techniques ◽  
Initial Setting

Crystalline admixtures are employed for waterproofing concrete. This type of admixtures can affect the early age performance of cement-based mixes. The electrical resistance properties of cement have been related to the initial setting time and to the hydration development. This paper proposes a system for remote monitoring of the initial setting time and the first days of the hardening of cement-based mortars to evaluate the effect of the incorporation of crystalline admixtures. The electrical resistance results have been confirmed by other characterization techniques such as thermogravimetric analysis and compressive strength measurements. From the electrical resistance monitoring it has been observed that the incorporation of crystalline admixtures causes a delay in the initial setting time and hydration processes. The measurements also allow to evaluate the influence of the amount of admixture used; thus, being very useful as a tool to define the optimum admixture dosage to be used.

High Volume Slag and Slag-Fly Ash Blended Cement Pastes Containing Nano Silica

2019 ◽  
Vol 967 ◽  
pp. 205-213
Author(s):  
Faiz U.A. Shaikh ◽  
Anwar Hosan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Paste ◽  
Ordinary Portland Cement ◽  
Blended Cement ◽  
High Volume ◽  
Ash Content ◽  
Partial Replacement ◽  
Nano Silica ◽  
Cement Pastes

This paper presents the effect of nanosilica (NS) on compressive strength and microstructure of cement paste containing high volume slag and high volume slag-fly ash blend as partial replacement of ordinary Portland cement (OPC). Results show that high volume slag (HVS) cement paste containing 60% slag exhibited about 4% higher compressive strength than control cement paste, while the HVS cement paste containing 70% slag maintained the similar compressive strength to control cement paste. However, about 9% and 37% reduction in compressive strength in HVS cement pastes is observed due to use of 80% and 90% slag, respectively. The high volume slag-fly ash (HVSFA) cement pastes containing total slag and fly ash content of 60% exhibited about 5%-16% higher compressive strength than control cement paste. However, significant reduction in compressive strength is observed in higher slag-fly ash blends with increasing in fly ash contents. Results also show that the addition of 1-4% NS improves the compressive strength of HVS cement paste containing 70% slag by about 9-24%. However, at higher slag contents of 80% and 90% this improvement is even higher e.g. 11-29% and 17-41%, respectively. The NS addition also improves the compressive strength by about 1-59% and 5-21% in high volume slag-fly ash cement pastes containing 21% fly ash+49%slag and 24% fly ash+56%slag, respectively. The thermogravimetric analysis (TGA) results confirm the reduction of calcium hydroxide (CH) in HVS/HVSFA pastes containing NS indicating the formation of additional calcium silicate hydrate (CSH) gels in the system. By combining slag, fly ash and NS in high volumes e.g. 70-80%, the carbon footprint of cement paste is reduced by 66-76% while maintains the similar compressive strength of control cement paste. Keywords: high volume slag, nanosilica, compressive strength, TGA, high volume slag-fly ash blend, CO2 emission.

Suitability of Cordia millenii Ash Blended Cement in Concrete Production

2016 ◽  
Vol 22 ◽  
pp. 59-67 ◽  
Author(s):  
Olusola Emmanuel Babalola ◽  
Paul O. Awoyera
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Blended Cement ◽  
Cementitious Materials ◽  
Strength Properties ◽  
Supplementary Cementitious Materials ◽  
Sieve Analysis ◽  
Concrete Production ◽  
Alternative Materials ◽  
Concrete Control

Supplementary cementitious materials are most needed to enhance a sustainable development in poor communities. It is pertinent to investigate the suitability of such alternative materials for construction. The present study evaluates the strength characteristics of concrete made with varied proportion of Cordia millenii ash blended with Portland cement. Chemical composition of Cordia millenii and the setting time when blended with cement was determined. Other laboratory tests performed on Cordia millenii blended cement include: sieve analysis and specific gravity. Five replacement percentages of Cordia millenii (5%, 10%, 15%, and 20%) were blended with cement in concrete. Control specimens were also produced with only cement. Tests to determine the workability, air entrained, bulk density and compressive strength properties of the concrete were also conducted. Results obtained revealed that optimum Cordia millenii mix is 10%, which yielded the highest density and compressive strength in the concrete.

Sign in / Sign up

Export Citation Format

Share Document