scholarly journals Effect of Calcium Nitrate on the Properties of Portland–Limestone Cement-Based Concrete Cured at Low Temperature

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1611
Author(s):  
Gintautas Skripkiūnas ◽  
Asta Kičaitė ◽  
Harald Justnes ◽  
Ina Pundienė
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Calcium Nitrate ◽  
Curing Temperature ◽  
Hardened Concrete ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Early Strength

The effect of calcium nitrate (CN) dosages from 0 to 3% (of cement mass) on the properties of fresh cement paste rheology and hardening processes and on the strength of hardened concrete with two types of limestone-blended composite cements (CEM II A-LL 42.5 R and 42.5 N) at different initial (two-day) curing temperatures (−10 °C to +20 °C) is presented. The rheology results showed that a CN dosage up to 1.5% works as a plasticizing admixture, while higher amounts demonstrate the effect of increasing viscosity. At higher CN content, the viscosity growth in normal early strength (N type) cement pastes is much slower than in high early strength (R type) cement pastes. For both cement-type pastes, shortening the initial and final setting times is more effective when using 3% at +5 °C and 0 °C. At these temperatures, the use of 3% CN reduces the initial setting time for high early strength paste by 7.4 and 5.4 times and for normal early strength cement paste by 3.5 and 3.4 times when compared to a CN-free cement paste. The most efficient use of CN is achieved at −5 °C for compressive strength enlargement; a 1% CN dosage ensures the compressive strength of samples at a −5 °C initial curing temperature, with high early strength cement exceeding 3.5 MPa but being less than the required 3.5 MPa in samples with normal early strength cement.

scholarly journals PROPERTIES OF CEMENT PASTE AND CONCRETE CONTAINING CALCIUM CARBIDE WASTE AS ADDITIVE

2016 ◽  
Vol 36 (1) ◽  
pp. 26-31
Author(s):  
EN Ogork ◽  
TS Ibrahim
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Drying Shrinkage ◽  
Calcium Carbide ◽  
Linear Shrinkage ◽  
Hardened Concrete ◽  
Concrete Compressive Strength ◽  
Initial Setting Time ◽  
Standard Procedures

This paper assessed the effect of calcium carbide waste (CCW) as additive on the properties of cement paste and concrete. The CCW used was sourced from a local panel beating workshop. It was sundried and sieved through a 75 µm sieve and characterized by X-Ray Fluorescence (XRF) analytical method. The consistency, setting times and drying linear shrinkage of cement paste with CCW addition of 0, 0.25, 0.5, 0.75 and 1.0 %, respectively by weight of cement were investigated in accordance with standard procedures. The slump values of fresh concrete containing CCW as additive and of 1:2:4 mix ratio and water-cement ratio of 0.5 was determined. A total of sixty numbers of 150 mm cubes of hardened concrete were tested for compressive strength at 1, 3, 7, 28 and 56 days of curing in accordance with standard procedures. The concrete compressive strength was also modeled using Minitab statistical software based on linear regression technique. The results of the investigations showed that CCW was predominantly of calcium oxide (95.69 %) and a combined SiO2, Al2O3 and Fe2O3 content of 3.14 %. The addition of CCW in cement decreased drying shrinkage (100 %), initial setting time (78 %) and final setting time (57 %), but increased consistency (14 %) at 1.0 % CCW content. The addition of CCW in concrete also showed slight increase in slump (6.5 %) and increase in compressive strength with increase in CCW additive up to 0.5 % and decrease in compressive strength with further increase in CCW content. The 28 days compressive strength of concrete with 0.5 % CCW content was 6.4 % more than normal, while that of concrete with 1.0 % CCW content was 14.9 % less than normal. The compressive strength model of CCW-concrete was developed with R2 value of 0.830 and could be used to predict concrete compressive strength. http://dx.doi.org/10.4314/njt.v36i1.4

scholarly journals Preparation and Performance of a New-Type Alkali-Free Liquid Accelerator for Shotcrete

2017 ◽  
Vol 2017 ◽  
pp. 1-9
Author(s):  
Yanping Sheng ◽  
Bin Xue ◽  
Haibin Li ◽  
Yunyan Qiao ◽  
Huaxin Chen ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Cement Mortar ◽  
Retention Rate ◽  
Setting Time ◽  
Test Results ◽  
Initial Setting Time ◽  
Initial Setting ◽  
New Type ◽  
And Performance

A new type of alkali-free liquid accelerator for shotcrete was prepared. Specifically, the setting time and strength and shrinkage performance of two kinds of Portland cement with the accelerator were fully investigated. Moreover, the accelerating mechanism of alkali-free liquid accelerator and the hydration process of the shotcrete with accelerator were explored. Results show that alkali-free liquid accelerator significantly shortened the setting time of cement paste, where the initial setting time of cement paste with 8 wt% of the accelerator was about 3 min and the final setting time was about 7 min. Compressive strength at 1 day of cement mortar with the accelerator could reach 23.4 MPa, which increased by 36.2% compared to the strength of cement mortar without the accelerator, and the retention rate of 28-day compressive strength reached 110%. In addition, the accelerator still shows a good accelerating effect under low temperature conditions. However, the shrinkage rate of the concrete increased with the amount of the accelerator. 5~8% content of accelerator is recommended for shotcrete in practice. XRD and SEM test results showed that the alkali-free liquid accelerator promoted the formation of ettringite crystals due to the increase of Al3+ and SO42- concentration.

Study on the Early Hydration of Cement Paste Containing Sodium Chloride

2014 ◽  
Vol 621 ◽  
pp. 35-38 ◽  
Author(s):  
Rahimah Embong ◽  
Andri Kusbiantoro
Keyword(s):  
Compressive Strength ◽  
Sodium Chloride ◽  
Cement Paste ◽  
Setting Time ◽  
Chloride Ion ◽  
Strength Development ◽  
Early Hydration ◽  
Initial Setting Time ◽  
Additive Component ◽  
Initial Setting

This paper studies the effect of sodium chloride as the additive component in cement paste. Sodium chloride was included at 0.5%, 1%, 1.5%, and 2% by weight of cement content. Analysis on the performance of this reagent was conducted via setting time, compressive strength, and porosity test. Based on the setting time analysis, the inclusion of sodium chloride can extend the initial setting time of cement paste up to 24.91% longer than control specimen. Obstruction on the formation of calcium silicate hydrate gel by sodium and chloride ion was one of the possible causes to this phenomenon. Acceleration on the compressive strength development by sodium chloride was also detected. It appears that sodium chloride was able to de-flocculate the coagulated cement particles and reduced the viscosities of cement slurries; hence resulted in faster early hydration process.

scholarly journals Investigation of Portland cement composites containing high amounts of different kinds of fly ashes

2019 ◽  
Author(s):  
Iwona Wilińska ◽  
Barbara Pacewska ◽  
Wojciech Kubissa
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Cement Composite ◽  
Fly Ashes ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Lower Heat ◽  
The Impact

Utilization of fluidized fly ash in cement composite is problematic, e.g. because of its changeable chemical composition and increased water demand of the mixture. However, this kind of by-product shows some self-cementing properties, which may be beneficial for low-cement mixtures. The article compares the impact of various kinds of fly ashes, i.e. fluidized fly ash and conventional one, and their mixtures on hydration of fly ash–cement compositions in relation to properties of final material. The amount of fly ash in the binder was 50 wt%. Calorimetry, thermal analysis (TG/DTG) and infrared spectroscopy were used. Compressive strength and water absorption of hardened composites were also registered. It was found that both fly ashes exhibit delay effect in fly ash-cement pastes which causes extension of initial setting time and lower heat released compared to the reference without fly ash. At later hydration days, fluidized fly ash develops higher pozzolanic activity than conventional one. Compositions with fluidized fly ash show better compressive strength compared to those containing conventional one. Mixing of different materials of high and low activity (fluidized and conventional fly ash in this case) seems to be a good way for creation of new cement replacement material.

scholarly journals Compressive Strength of Concrete with Nano Cement

2021 ◽  
Author(s):  
Jemimah Carmichael Milton ◽  
Prince Arulraj Gnanaraj
Keyword(s):  
Compressive Strength ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Cement Paste ◽  
Cement Mortar ◽  
Setting Time ◽  
Replacement Level ◽  
Initial Setting Time ◽  
Initial Setting

Nano technology plays a very vital role in all the areas of research. The incorporation of nano materials in concrete offers many advantages and improves the workability, the strength and durability properties of concrete. In this study an attempt has been made to carry out an experimental investigation on concrete in which cement was replaced with nano sized cement. Ordinary Portland cement of 53 grade was ground in a ball grinding mill to produce nano cement. The characterization of nano cement was studied using Scanning Electron Microscope (SEM), Brunauer Emmett–Teller (BET), Energy Dispersive X ray microanalysis (EDAX) and Fourier Transform Infrared Spectroscopy (FTIR). From the characterization studies, it was confirmed that particles were converted to nano size, the specific surface area increased and the chemical composition remained almost the same. The properties of cement paste with and without nano cement were found. For the experimental study, cement was replaced with 10%, 20%, 30%, 40% and 50% of nano cement. Cement mortar of ratio 1:3 and concrete of grades M20, M30, M40 and M50 were used. Compressive strength of cement mortar and concrete with different percentages of nano cement was found. The cement mortar was also subjected to micro structural study. It was found that the strength increased even up to the replacement level of 50%. Further increase in the replacement is not possible since the addition of nano cement reduces the initial and final setting time of cement paste. At 50% replacement level, the initial setting time got reduced to 30 minutes which the least permitted value as per IS 12269: 2013. The increase in strength was due to the fact that nano cement acts not only as a filler material but also the reactivity increased due to the higher specific surface area. The SEM image shows the formation of additional C-S-H gel. The percentage increase in compressive strength was found to increase up to 32%. The workability of concrete with nano cement was found to be significantly more than that of the normal cement concrete.

Behavior of Cement Pastes and Mortar Containing Phosphogypsum

2015 ◽  
Vol 668 ◽  
pp. 181-188 ◽  
Author(s):  
Hanan El Nouhy ◽  
Enas Khattab ◽  
Sayieda Zeedan
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Blended Cement ◽  
X Ray Diffraction ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Second Stage ◽  
Setting Times ◽  
Initial Setting ◽  
Two Stages

The aim of this study is to investigate the effects of phosphogypsum on the properties of both cement pastes and mortars. Normal Portland cement CEM Ι 32,5N, Limestone Blended cement CEM ΙΙ B-L32,5N, and Slag cement CEM ΙΙ A-S32,5N were used. These cements were partially substituted by 0,2,4,6,8,10,and 15% of phosphogypsum. The test program was divided to two stages. In the first stage, tests were conducted according to BSEN 196, namely setting times (initial and final), soundness, and compressive strength (at ages 7 and 28 days). In the second stage, X-ray diffraction (XRD), and scanning electron microscope (SEM) were conducted on selected mixes from first stage. The results show that the three types of cements with the various replacement percentages of phosphogypsum met the limit of initial setting time, as well as, provided soundness of 2 mm. Also, in terms of compressive strength, it was proven, that it is possible to partially replace the three tested types of cements by phosphogypsum by up to 8%and 15% with regard to cement/sand ratio of (1:3) and (1:2) respectively.

The Influence of Alcohol Amine Admixtures on the Macroscopic Properties of Portland Cement Paste

2014 ◽  
Vol 525 ◽  
pp. 573-579
Author(s):  
Tian Yong Huang ◽  
Dong Min Wang ◽  
Ze Liu
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Cement Paste ◽  
Setting Time ◽  
Initial Setting Time ◽  
Final Setting Time ◽  
Cement Mortars ◽  
Macroscopic Properties ◽  
Initial Setting

It is studied the influence of triethanolamine (TEA), diethylenetriamine (DEA), Triisopropanolamine (TIPA), aminoethyl ethanolamine (AE), and polyvinyl alcohol ammonium phosphate (PAAP) at different dosages on the properties of fresh and hardened cement pastes and mortars prepared by Portland cement, including standard consistency water, setting time, the cement paste fluidity, and compressive and flexural strength. It is showed that the high polarity alcohol amine molecules exhibit strong chemical interactions with cement matrix, which are reflected in modified macroscopic properties of the cement system. All alcohol amine admixtures increased the standard consistency water and decreased cement paste fluidity of Portland cement. TEA significantly shortened the initial setting time and final setting time of Portland cement. On the other hand, TIPA, DEA, AE and PAAP extended the initial setting time of cement but shortened the cement final setting time. All alcohol amine admixtures except TIPA at 0.2 and 0.5 dosage increased the compressive and flexural strength of the Portland cement mortars at 3 days. Especially when the dosage of PAAP is 1, the compressive strength of the Portland cement mortars at 3 days is increased 10.5MPa. All alcohol amine admixtures except AE at 0.2 and 0.5 dosage increase the compressive and flexural strength of the Portland cement mortars at 28 days, Especially when the dosage of TIPA is 1, the compressive strength of the Portland cement mortars at 28 days is increased 8.8MPa.

scholarly journals Aplikasi Response Surface Methodology pada Optimasi Penambahan Blast Furnace Slag Terhadap Waktu Pengikatan dan Kuat Tekan Semen

2020 ◽  
Vol 4 (1) ◽  
pp. 61
Author(s):  
Hardjono Hardjono ◽  
Cucuk Evi Lusiani ◽  
Agung Ari Wibowo ◽  
Mochammad Agung Indra Iswara
Keyword(s):  
Compressive Strength ◽  
Response Surface Methodology ◽  
Blast Furnace ◽  
Response Surface ◽  
Blast Furnace Slag ◽  
Setting Time ◽  
Initial Setting Time ◽  
Initial Setting ◽  
Central Composite ◽  
Furnace Slag

Produksi semen setengah jadi (clinker) membutuhkan energi yang tinggi sehingga menggunakan batu bara dalam jumlah besar. Hal ini menyebabkan biaya produksi dari pabrik semen juga tinggi. Kebutuhan energi yang besar untuk menghasilkan clinker tersebut dapat dikurangi dengan menambahan blast furnace slag sebagai campuran pembuatan semen. Campuran clinker dapat menghasilkan produk semen yang memiliki waktu pengikatan dan kuat tekan sesuai SNI. Pengaruh penambahan blast furnace slag sebagai campuran clinker terhadap waktu pengikatan dan kuat tekan semen dapat dioptimalkan dengan response surface methodology (RSM) menggunakan Central Composite Design (CCD). Optimasi dengan menggunakan RSM bertujuan untuk mengetahui kondisi optimum pada penambahan blast furnace slag dan clinker terhadap variabel respon berupa waktu pengikatan awal, waktu pengikatan akhir, dan kuat tekan. Hasil uji ANOVA dan analisis response surface menunjukkan bahwa penambahan blast furnace slag sebagai campuran dalam pembuatan semen memberikan pengaruh yang signifikan terhadap waktu pengikatan awal, waktu pengikatan akhir, dan kuat tekan. Penambahan 5% blast furnace slag dengan 92,5% clinker pada campuran clinker dan gypsum merupakan kondisi optimum yang memberikan pengaruh signifikan terhadap variabel respon.The production of clinker consumes high energy and causes high production cost of cement industry. It can be reduced by adding blast furnace slag as a mixture in cement production. The blast furnace slag - clinker mixture can produce cement with setting time and compressive strength according to SNI. The effect of the addition of blast furnace slag as a clinker mixture to the setting time and compressive strength of cement can be optimized by response surface methodology (RSM) using Central Composite Design (CCD). Optimization by using RSM aims to determine the optimum condition of the blast furnace slag – clinker mixture to the initial setting time, final setting time, and compressive strength. ANOVA test results and response surface analysis show that the addition of blast furnace slag into the cement mixture has a significant influence on the initial setting time, final setting time, and compressive strength. The addition of  5% blast furnace slag with  92.5% clinker in the mixture of clinker and gypsum is the optimum condition which gives a significant effect on the response variable.

scholarly journals Analysis of the Influence of Crystalline Admixtures at Early Age Performance of Cement-Based Mortar by Electrical Resistance Monitoring

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5705
Author(s):  
Rubén Beltrán Cobos ◽  
Fabiano Tavares Pinto ◽  
Mercedes Sánchez Moreno
Keyword(s):  
Compressive Strength ◽  
Thermogravimetric Analysis ◽  
Remote Monitoring ◽  
Electrical Resistance ◽  
Setting Time ◽  
Early Age ◽  
Resistance Monitoring ◽  
Initial Setting Time ◽  
Characterization Techniques ◽  
Initial Setting

Crystalline admixtures are employed for waterproofing concrete. This type of admixtures can affect the early age performance of cement-based mixes. The electrical resistance properties of cement have been related to the initial setting time and to the hydration development. This paper proposes a system for remote monitoring of the initial setting time and the first days of the hardening of cement-based mortars to evaluate the effect of the incorporation of crystalline admixtures. The electrical resistance results have been confirmed by other characterization techniques such as thermogravimetric analysis and compressive strength measurements. From the electrical resistance monitoring it has been observed that the incorporation of crystalline admixtures causes a delay in the initial setting time and hydration processes. The measurements also allow to evaluate the influence of the amount of admixture used; thus, being very useful as a tool to define the optimum admixture dosage to be used.

Sign in / Sign up

Export Citation Format

Share Document