MORPHOLOGY AND ELECTRICAL RESISTIVITY OF AuCu NANOFILM ALLOYS

2008 ◽  
Vol 15 (06) ◽  
pp. 881-888 ◽  
Author(s):  
R. D. MALDONADO ◽  
A. I. OLIVA
Keyword(s):  
Thin Films ◽  
Electrical Resistivity ◽  
Total Thickness ◽  
X Ray Diffraction ◽  
Atomic Concentration ◽  
Vacuum Oven ◽  
Force Microscopy ◽  
Atomic Force ◽  
Abrupt Changes ◽  
P Type

Au / Cu thin films (33–320 nm thickness) were deposited by thermal evaporation on p-type silicon (100) substrates. Two groups of these bimaterial films were alloyed into a vacuum oven by diffusion. The first group was prepared with 24% Au atomic concentration (i.e. 33, 96, 158, 224, and 320 nm as AuCu total thickness). The second group was prepared changing the Au atomic concentration from 10% to 90%, with 10% Au steps and similar total thickness (100 nm). Prepared alloys were characterized with atomic force microscopy (AFM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), and collinear four-probe techniques in order to obtain their morphology, stoichiometry, crystalline structure, and electrical resistivity, respectively. Particularly, electrical resistivity presented abrupt changes with the atomic concentration and the annealing temperature with important differences as compared with pure Au and Cu thin films.

scholarly journals Surface Morphology and Electrical Resistivity in Polycrystalline Au/Cu/Si(100) System

2017 ◽  
Vol 2017 ◽  
pp. 1-8
Author(s):  
T. E. Novelo ◽  
G. M. Alonzo-Medina ◽  
P. Amézaga-Madrid ◽  
R. D. Maldonado
Keyword(s):  
Electrical Resistivity ◽  
Thermal Evaporation ◽  
X Ray Diffraction ◽  
Atomic Concentration ◽  
Final Thickness ◽  
Vacuum Oven ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Evaporation Technique

This work describes the analysis of morphology and electrical resistivity (ρ) obtained in the Au/Cu/Si system. The Au/Cu bilayers were deposited by thermal evaporation technique with thicknesses from 50 to 250 nm on SiOx/Si(100) substrates. The Au : Cu concentration ratio of the samples was of 25 : 75 at%. The bilayers were annealed into a vacuum oven with argon atmosphere at 660 K for one hour. The crystalline structures of AuCu and CuSi alloys were confirmed by X-ray diffraction analysis. The scanning electron microscopy (SEM), the atomic force microscopy (AFM), and the energy dispersive spectroscopy (EDS) were used to study the morphology, final thickness, and the atomic concentration of the alloys formed, respectively. The four-point probe technique was used to measure the electrical resistivity (ρ) in the prepared alloys as a function of thickness. The ρ value was measured and it was numerically compared with the Fuchs–Sondheimer (FS) and the Mayadas–Shatzkes (MS) models of resistivity. Results show values of electrical resistivity between 0.9 and 1.9 μΩ-cm. These values are four times smaller than the values of the AuCu systems reported in literature.

Synthesis and Characterization of Semiconductor Composites Gas Sensors Based on ZnO Doped TiO2 Thin Films by Laser-Induced Plasma

2021 ◽  
Vol 900 ◽  
pp. 112-120
Author(s):  
Souad G. Khalil ◽  
Mahdi M. Mutter
Keyword(s):  
Thin Films ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Electrical Characterization ◽  
X Ray Diffraction ◽  
Type Conductivity ◽  
Force Microscopy ◽  
Atomic Force ◽  
P Type

This work presents the development of n-type (TiO2) and p-type (ZnO) gas-sensitive materials from ZnO doped TiO2 thin films prepared by pulsed laser deposition technique (PLD) on a glass substrate as a gas sensor of CO2 gas. TiO2 gas-sensing layers have been deposited over a range of ZnO content (0, 20, and 40) wt %. The obtained thin films analysis by atomic force microscopy (AFM), and X-ray diffraction (XRD). Electrical characterization shows that TiO2:ZnO thin films were p-type conductivity and ZnO added was unable to change the composition to the n-type conductivity. There are notable gas-sensing response differences between n-type and p-type ZnO doped TiO2 thin film. The responses toward all tested oxidizing gases tend to increase with operating temperature for the n-type TiO2 films. Besides, the p-type ZnO doping results in a significant response improvement toward tested oxidizing gases such as CO2 gas at the low operating temperature of 60 °C.

ANNEALING TIME EFFECT ON NANOSTRUCTURED n-ZnO/p-Si HETEROJUNCTION PHOTODETECTOR PERFORMANCE

2015 ◽  
Vol 22 (02) ◽  
pp. 1550027 ◽  
Author(s):  
NADIR. F. HABUBI ◽  
RAID. A. ISMAIL ◽  
WALID K. HAMOUDI ◽  
HASSAM. R. ABID
Keyword(s):  
Annealing Time ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Zno Nps ◽  
Force Microscopy ◽  
Atomic Force ◽  
Junction Type ◽  
P Type ◽  
Quartz Substrates ◽  
Two Peaks

In this work, n- ZnO /p- Si heterojunction photodetectors were prepared by drop casting of ZnO nanoparticles (NPs) on single crystal p-type silicon substrates, followed by (15–60) min; step-annealing at 600∘C. Structural, electrical, and optical properties of the ZnO NPs films deposited on quartz substrates were studied as a function of annealing time. X-ray diffraction studies showed a polycrystalline, hexagonal wurtizte nanostructured ZnO with preferential orientation along the (100) plane. Atomic force microscopy measurements showed an average ZnO grain size within the range of 75.9 nm–99.9 nm with a corresponding root mean square (RMS) surface roughness between 0.51 nm–2.16 nm. Dark and under illumination current–voltage (I–V) characteristics of the n- ZnO /p- Si heterojunction photodetectors showed an improving rectification ratio and a decreasing saturation current at longer annealing time with an ideality factor of 3 obtained at 60 min annealing time. Capacitance–voltage (C–V) characteristics of heterojunctions were investigated in order to estimate the built-in-voltage and junction type. The photodetectors, fabricated at optimum annealing time, exhibited good linearity characteristics. Maximum sensitivity was obtained when ZnO / Si heterojunctions were annealed at 60 min. Two peaks of response, located at 650 nm and 850 nm, were observed with sensitivities of 0.12–0.19 A/W and 0.18–0.39 A/W, respectively. Detectivity of the photodetectors as function of annealing time was estimated.

Nanocrystalline Solutions as Precursors to The Spray Deposition of Cdte Thin Films

1995 ◽  
Vol 382 ◽  
Author(s):  
Martin Pehnt ◽  
Douglas L. Schulz ◽  
Calvin J. Curtis ◽  
Helio R. Moutinho ◽  
Amy Swartzlander ◽  
...  
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Grain Size ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Cdte Nanoparticles ◽  
Atomic Force ◽  
Vis Spectroscopy ◽  
Cdte Thin Films

ABSTRACTIn this article we report the first nanoparticle-derived route to smooth, dense, phase-pure CdTe thin films. Capped CdTe nanoparticles were prepared by injection of a mixture of Cd(CH3)2, (n-C8H17)3 PTe and (n-C8H17)3P into (n-C8H17)3PO at elevated temperatures. The resultant nanoparticles 32-45 Å in diameter were characterized by x-ray diffraction, UV-Vis spectroscopy, transmission electron microscopy, thermogravimetric analysis and energy dispersive x-ray spectroscopy. CdTe thin film deposition was accomplished by dissolving CdTe nanoparticles in butanol and then spraying the solution onto SnO2-coated glass substrates at variable susceptor temperatures. Smooth and dense CdTe thin films were obtained using growth temperatures approximately 200 °C less than conventional spray pyrolysis approaches. CdTe films were characterized by x-ray diffraction, UV-Vis spectroscopy, atomic force microscopy, and Auger electron spectroscopy. An increase in crystallinity and average grain size as determined by x-ray diffraction was noted as growth temperature was increased from 240 to 300 °C. This temperature dependence of film grain size was further confirmed by atomic force microscopy with no remnant nanocrystalline morphological features detected. UV-Vis characterization of the CdTe thin films revealed a gradual decrease of the band gap (i.e., elimination of nanocrystalline CdTe phase) as the growth temperature was increased with bulk CdTe optical properties observed for films grown at 300 °C.

Studies of Nanomechanical Properties of Pulsed Laser Deposited NbN films on Si Using Nanoindentation

2012 ◽  
Vol 1424 ◽  
Author(s):  
M. A. Mamun ◽  
A. H. Farha ◽  
Y. Ufuktepe ◽  
H. E. Elsayed-Ali ◽  
A. A. Elmustafa
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
Niobium Nitride ◽  
X Ray Diffraction ◽  
Si Substrate ◽  
Force Microscopy ◽  
Atomic Force ◽  
Wide Range ◽  
Pile Up ◽  
Average Modulus

ABSTRACTNanomechanical and structural properties of pulsed laser deposited niobium nitride thin films were investigated using X-ray diffraction, atomic force microscopy, and nanoindentation. NbN film reveals cubic δ-NbN structure with the corresponding diffraction peaks from the (111), (200), and (220) planes. The NbN thin films depict highly granular structure, with a wide range of grain sizes that range from 15-40 nm with an average surface roughness of 6 nm. The average modulus of the film is 420±60 GPa, whereas for the substrate the average modulus is 180 GPa, which is considered higher than the average modulus for Si reported in the literature due to pile-up. The hardness of the film increases from an average of 12 GPa for deep indents (Si substrate) measured using XP CSM and load control (LC) modes to an average of 25 GPa measured using the DCM II head in CSM and LC modules. The average hardness of the Si substrate is 12 GPa.

scholarly journals Influence of the growth parameters of TiO2 thin films deposited by the MOCVD method

Cerâmica ◽  
2002 ◽  
Vol 48 (305) ◽  
pp. 38-42 ◽  
Author(s):  
M. I. B. Bernardi ◽  
E. J. H. Lee ◽  
P. N. Lisboa-Filho ◽  
E. R. Leite ◽  
E. Longo ◽  
...  
Keyword(s):  
Thin Films ◽  
Growth Parameters ◽  
Structural Characteristics ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Tio2 Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Deposition Parameters

The synthesis of TiO2 thin films was carried out by the Organometallic Chemical Vapor Deposition (MOCVD) method. The influence of deposition parameters used during growth on the final structural characteristics was studied. A combination of the following experimental parameters was studied: temperature of the organometallic bath, deposition time, and temperature and substrate type. The high influence of those parameters on the final thin film microstructure was analyzed by scanning electron microscopy with electron dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction.

Epitaxial BaTiO3 Thin Films on Different Substrates for Optical Waveguide Applications

1999 ◽  
Vol 597 ◽  
Author(s):  
M. Siegert ◽  
Judit G. Lisoni ◽  
C. H. Lei ◽  
A. Eckau ◽  
W. Zander ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Waveguides ◽  
Rutherford Backscattering Spectrometry ◽  
Optical Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Transmission Electron

AbstractIn the process of developing thin film electro-optical waveguides we investigated the influence of different substrates on the optical and structural properties of epitaxial BaTiO3 thin films. These films are grown by on-axis pulsed laser deposition (PLD) on MgO(100), MgAl2O4(100), SrTiO3(100) and MgO buffered A12O3(1102) substrates. The waveguide losses and the refractive indices were measured with a prism coupling setup. The optical data are correlated to the results of Rutherford backscattering spectrometry/ion channeling (RBS/C). X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). BaTiO3 films on MgO(100) substrates show planar waveguide losses of 3 dB/cm and ridge waveguide losses of 5 dB/cm at a wavelength of 633 nm.

Biocompatibility Studies of the Nitinol Thin Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C.Z. Dinu ◽  
R. Tanasa ◽  
V.C. Dinca ◽  
A. Barbalat ◽  
C. Grigoriu ◽  
...  
Keyword(s):  
Thin Films ◽  
Surface Morphology ◽  
Fibroblast Cell ◽  
Vero Cells ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Fetal Bovine ◽  
Fibroblast Cell Lines

AbstractPulsed Laser Deposition method (PLD) was used to grow nitinol (NiTi) thin films with goal of investigating their biocompatibility. High purity Ni and Ti targets were alternatively ablated in vacuum with a laser beam (λ=355 nm, 10 Hz) and the material was collected on room temperature Ti substrates. X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and atomic force microscopy analyses have been performed to investigate the chemical composition, crystalline structure and surface morphology of the NiTi films. The nitinol layers biocompatibility has been tested using as a metric the extent to whichthe cells adhereduring the culture period on the surface of NiTi layers deposited on Ti substrates. Vero and fibroblast cell lines dispersed into MEM (Eagle) solution containing 8% fetal bovine serum, at 37° C, were used for tests. Preliminary studies indicate that the interaction at the interface is specifically controlled by the surface morphology, (especially by surface roughness), and by the chemical state of the surface. Cell behavior after contact with NiTi/Ti structure for different intervals (18, 22 and 25 days for the Vero cells, and after 10 and 25 days for fibroblasts) supports the conclusion that NiTi is a very good candidate as a biocompatible material.

Dielectric Properties of Sol-Gel Derived MgAl2O4 Thin Films

2012 ◽  
Vol 151 ◽  
pp. 314-318
Author(s):  
Ching Fang Tseng ◽  
Cheng Hsing Hsu ◽  
Chun Hung Lai
Keyword(s):  
Thin Films ◽  
Annealing Temperature ◽  
Sol Gel ◽  
Dissipation Factor ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Preheating Temperature ◽  
Surface Morphologies

This paper describes microstructure characteristics of MgAl2O4 thin films were deposited by sol-gel method with various preheating temperatures and annealing temperatures. Particular attention will be paid to the effects of a thermal treatment in air ambient on the physical properties. The annealed films were characterized using X-ray diffraction. The surface morphologies of treatment film were examined by scanning electron microscopy and atomic force microscopy. At a preheating temperature of 300oC and an annealing temperature of 700oC, the MgAl2O4 films with 9 μm thickness possess a dielectric constant of 9 at 1 kHz and a dissipation factor of 0.18 at 1 kHz.

Stress origin and relaxation in epitaxial AlN thin films on SiC

2001 ◽  
Vol 696 ◽  
Author(s):  
Ravi Bathe ◽  
R.D. Vispute ◽  
Daniel Habersat ◽  
R. P. Sharma ◽  
T. Venkatesan ◽  
...  
Keyword(s):  
Thin Films ◽  
Rutherford Backscattering Spectrometry ◽  
Wide Band ◽  
X Ray Diffraction ◽  
Wide Band Gap ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Highly Strained

AbstractWe have investigated the epitaxy, surfaces, interfaces, and defects in AlN thin films grown on SiC by pulsed laser deposition. The stress origin, evolution, and relaxation in these films is reported. The crystalline structure and surface morphology of the epitaxially grown AlN thin films on SiC (0001) substrates have been studied using x-ray diffraction (θ–2θ, ω, and Ψ scans) and atomic force microscopy, respectively. The defect analysis has been carried out by using Rutherford backscattering spectrometry and ion channeling technique. The films were grown at various substrate temperatures ranging from room temperature to 1100 °C. X-ray diffraction measurements show highly oriented AlN films when grown at temperatures of 750- 800 °C, and single crystals above 800 °C. The films grown in the temperature range of 950 °C to 1000 °C have been found to be highly strained, whereas the films grown above 1000 °C were found to be cracked along the crystallographic axes. The results of stress as a function of growth temperature, thermal mismatch, growth mode, and buffer layer thickness will be presented, and the implications of these results for wide band gap power electronics will be discussed.

Sign in / Sign up

Export Citation Format

Share Document