Nonlinear Finite Element Analysis of FRP Strengthened RC Beams with Bond-Slip Effect

2017 ◽  
Vol 14 (03) ◽  
pp. 1750032 ◽  
Author(s):  
Prabin Pathak ◽  
Y. X. Zhang ◽  
Xiaodan Teng
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Structural Behavior ◽  
Slip Effect ◽  
Rc Beams ◽  
Element Analysis ◽  
Bond Slip ◽  
Research Findings ◽  
Parametric Studies

This paper investigates the structural behavior of fiber reinforced polymer (FRP) strengthened reinforced concrete (RC) beams by developing a new simple, efficient and accurate finite element model (FEM-B). In addition to the FRP, concrete and steel rebars, the adhesive and stirrups which have been generally ignored in the reported models from literatures are considered in the new models. At first, a finite element model (FEM-P) is developed assuming perfect bond between concrete, FRP and adhesive interfaces. Then the FEM-P model is expanded to form the FEM-B model by including the bond-slip effect between concrete, FRP and adhesive interfaces. The developed new finite element models (FEM-B and FEM-P) are validated against experimental results and demonstrate to be effective for the structural analysis of FRP strengthened RC beams. Furthermore, parametric studies are carried out to learn the effects of types and thickness of FRP on the structural behavior of FRP strengthened RC beams based on the FEM-B model. The research findings are summarized finally.

Finite Element Simulation for Nonlinear Finite Element Analysis of FRP Strengthened RC Beams with Bond-Slip Effect

2016 ◽  
Vol 846 ◽  
pp. 440-445
Author(s):  
Prabin Pathak ◽  
Yi Xia Zhang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Plastic Material ◽  
Element Model ◽  
Elastic Model ◽  
Slip Effect ◽  
Rc Beams ◽  
Element Analysis ◽  
Bond Slip ◽  
Nonlinear Properties

A new simple, efficient and accurate finite element model denoted as FEM-B is developed for the analysis of structural behavior of FRP strengthened RC beams with bond-slip effect. Geometric nonlinearity and material nonlinear properties of concrete and steel rebar are accounted for this model. Concrete, steel, FRP and adhesive are modelled as Solid 65, Link 180, Shell181 and Solid 45 respectively. Concrete is modelled using Nitereka and Neal’s model for compression, isotropic and linear elastic model before cracking for tension and strength gradually reduces to zero after cracking, whereas steel is assumed to be elastic perfectly plastic material. The material of FRP is considered to be linearly elastic until rupture, and adhesive is assumed to be linearly elastic. The bond slip between concrete, adhesive and FRP is based on the bilinear law, which is modelled using spring element Combin 39.The developed new finite element model FEM-B is validated against experimental results, and demonstrates to be effective for the structural analysis of FRP strengthened RC beams.

Contact Nonlinear Numerical Simulation of Steel and Concrete in Wind Turbine Foundation

2012 ◽  
Vol 204-208 ◽  
pp. 1194-1199 ◽  
Author(s):  
Chao Fei Wang ◽  
Wei Rong Lv ◽  
Wen Luo
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Wind Turbine ◽  
Element Model ◽  
Element Analysis ◽  
Bond Slip ◽  
Nonlinear Numerical Simulation ◽  
Nonlinear Finite Element Model ◽  
Good Agreement

Effective simulation and analysis about wind turbine foundation simplified model experiment were conducted by using general finite element analysis (FEA) program ANSYS. Nonlinear finite element model with surface-to-surface contact pair was built to study the strain distribution of the steel interface and slip between steel and concrete. Relevant strain and spreading length curves under the load of every class were obtained. The numerical simulation results were in good agreement with the experimental results. And proper parameters of bond-slip relationship for steel and concrete in wind turbine foundation were confirmed. The finite element model established and analysis results can provide a theoretical reference for later research, and have significant value for optimal design of wind turbine foundation.

Nonlinear Finite Element Analysis of Corroded Reinforced Concrete Lock-Walls

2011 ◽  
Vol 101-102 ◽  
pp. 329-332
Author(s):  
Fu Lai Qu ◽  
Shun Bo Zhao ◽  
Zhi Mei Zhou ◽  
Baoan Yuan
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Strength ◽  
Element Model ◽  
Steel Reinforcement ◽  
Nonlinear Finite Element ◽  
Flexural Behavior ◽  
Element Analysis ◽  
Bond Slip

Reinforcement and concrete can work together to bear load in reinforced concrete structures, one of the main reasons is the relatively prefect bond between reinforcement and concrete. When steel reinforcement corrodes, the bond strength decreases and leads to the degradation of the reinforced concrete members. This paper built a finite element model by selecting appropriate stress-strain relationship of concrete and reinforcement, bond-slip relationship between concrete and corroded steel bars. The flexural behavior of corroded reinforced concrete lock-walls was analyzed by nonlinear finite element method. The calculated results were compared with the test results to verify the reliability of the finite element model. Finally, the influence of corrosion level of steel reinforcement and concrete strength on the normal section bearing capacity of lock-walls were discussed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Wear Modeling of Nanometer Thick Protective Coatings

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Jungkyu Lee ◽  
Youfeng Zhang ◽  
Robert M. Crone ◽  
Narayanan Ramakrishnan ◽  
Andreas A. Polycarpou
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Protective Coatings ◽  
Element Model ◽  
Disk Surface ◽  
Magnetic Storage ◽  
Theoretical Frameworks ◽  
Storage Devices ◽  
Parametric Studies ◽  
Magnetic Storage Devices

Use of nanometer thin films has received significant attention in recent years because of their advantages in controlling friction and wear. There have been significant advances in applications such as magnetic storage devices, and there is a need to explore new materials and develop experimental and theoretical frameworks to better understand nanometer thick coating systems, especially wear characteristics. In this work, a finite element model is developed to simulate the sliding wear between the protruded pole tip in a recording head (modeled as submicrometer radius cylinder) and a rigid asperity on the disk surface. Wear is defined as plastically deformed asperity and material yielding. Parametric studies reveal the effect of the cylindrical asperity geometry, material properties, and contact severity on wear. An Archard-type wear model is proposed, where the wear coefficients are directly obtained through curve fitting of the finite element model, without the use of an empirical coefficient. Limitations of such a model are also discussed.

scholarly journals Sensitivity Analysis of the Influence of Structural Parameters on Dynamic Behaviour of Highly Redundant Cable-Stayed Bridges

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
B. Asgari ◽  
S. A. Osman ◽  
A. Adnan
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Structural Parameters ◽  
Element Model ◽  
Structural Behavior ◽  
Model Tuning ◽  
The Finite Element Model ◽  
Cable Stayed Bridges

The model tuning through sensitivity analysis is a prominent procedure to assess the structural behavior and dynamic characteristics of cable-stayed bridges. Most of the previous sensitivity-based model tuning methods are automatic iterative processes; however, the results of recent studies show that the most reasonable results are achievable by applying the manual methods to update the analytical model of cable-stayed bridges. This paper presents a model updating algorithm for highly redundant cable-stayed bridges that can be used as an iterative manual procedure. The updating parameters are selected through the sensitivity analysis which helps to better understand the structural behavior of the bridge. The finite element model of Tatara Bridge is considered for the numerical studies. The results of the simulations indicate the efficiency and applicability of the presented manual tuning method for updating the finite element model of cable-stayed bridges. The new aspects regarding effective material and structural parameters and model tuning procedure presented in this paper will be useful for analyzing and model updating of cable-stayed bridges.

scholarly journals Analysis for Wrinkling Behavior of Girth-Welded Line Pipe

1996 ◽  
Author(s):  
Luiz T. Souza ◽  
David W. Murray
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Internal Pressure ◽  
Experimental Test ◽  
Element Model ◽  
Element Analysis ◽  
Line Pipe ◽  
New Era ◽  
Analytical Tools

The paper presents results for finite element analysis of full-sized girth-welded specimens of line pipe and compares these results with the behavior exhibited by test specimens subjected to constant axial force, internal pressure and monotonically increasing curvatures. Recommendations for the ‘best’ type of analytical finite element model are given. Comparisons between the behavior predicted analytically and the observed behavior of the experimental test specimens are made. The mechanism of wrinkling is explained and the evolution of the deformed configurations for different wrinkling modes is examined. It is concluded that the analytical tools now available are sufficiently reliable to predict the behavior of pipe in a manner that was not previously possible and that this should create a new era for the design and assessment of pipelines if the technology is properly exploited by industry.

scholarly journals A Novel Method for Tooth Bending Stress Calculation of Gears With Asymmetric Teeth

2021 ◽  
Author(s):  
Oguz DOGAN ◽  
Celalettin YUCE ◽  
Fatih KARPAT
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Experimental Studies ◽  
Element Model ◽  
Bending Stress ◽  
Element Analysis ◽  
Stress Calculation ◽  
Bending Stresses ◽  
New Equation ◽  
Asymmetric Factor

Abstract Today, gear designs with asymmetric tooth profiles offer essential solutions in reducing tooth root stresses of gears. Although numerical, analytical, and experimental studies are carried out to calculate the bending stresses in gears with asymmetric tooth profiles a standard or a simplified equation or empirical statement has not been encountered in the literature. In this study, a novel bending stress calculation procedure for gears with asymmetric tooth profiles is developed using both the DIN3990 standard and the finite element method. The bending stresses of gears with symmetrical profile were determined by the developed finite element model and was verified by comparing the results with the DIN 3990 standard. Using the verified finite element model, by changing the drive side pressure angle between 20° and 30° and the number of teeth between 18 and 100, 66 different cases were examined and the bending stresses in gears with asymmetric profile were determined. As a result of the analysis, a new asymmetric factor was derived. By adding the obtained asymmetric factor to the DIN 3390 formula, a new equation has been derived to be used in tooth bending stresses of gears with asymmetric profile. Thanks to this equation, designers will be able to calculate tooth bending stresses with high precision in gears with asymmetric tooth profile without the need for finite element analysis.

Simulation of Thermo-Mechanical Models for Hot Formed Parts by Numerical Experiments

2014 ◽  
Vol 663 ◽  
pp. 668-674
Author(s):  
Azman Senin ◽  
Zulkifli Mohd Nopiah ◽  
Muhammad Jamhuri Jamaludin ◽  
Ahmad Zakaria
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Prediction Accuracy ◽  
Research Work ◽  
Deformation Characteristic ◽  
Element Model ◽  
Forming Limit ◽  
Prototype Model ◽  
New Production ◽  
Element Analysis

The Finite-Element Analysis (FEA) is a prediction methodology that facilitates product designers produced the part design with manufacturing focused. With the similar advantages, manufacturing engineers are capable of build the first actual car model from the new production Draw Die. This approach has eliminated the requirement to manufacture the prototype model from soft tool parts and soft tool press die. However, the prediction accuracy of FEA is a major topic of research work in automotive sector's practitioners and academia as current accuracy level is anticipated at 60%. The objective of works is to assess the prediction accuracy on deformation results from mass production stamped parts. The Finite-element model is developed from the CAD data of the production tools. Subsequently, finite-element model for production tools is discretized with shell elements to avoid computation errors in the simulation process. The sheet blank material with 1.5 mm and 2.0 mm thickness is discredited by shell (2D modeling) and solid elements (3D modeling) respectively. The input parameters for the simulation model for both elements are attained from the actual setup at Press Machine and Production Tool. The analysis of deformation and plastic strain are performed for various setup parameters. Finally, the deformation characteristic such as Forming Limit Diagram (FLD) and thinning are compared for all simulated models.

Sign in / Sign up

Export Citation Format

Share Document